WINCODE LP433A User manual

LP423A / LP433A USER MANUAL
User Manual：LP4 series
Issue Date：2016/11/14
Version 2.0

LP4 USER MANUAL
- 2 -
Declaration
The content of this manual is subject to change without prior notice and cannot be
altered without written permission obtained from Wincode Technology Co., Ltd
(hereinafter referred to as “Wincode”). No part of this manual may be reproduced or
transmitted in any form by any means. This manual includes the installation instruction
and detailed description of possible questions in the operation. Wincode has reserved
the right to improve product including technology, components, software and
hardware.
Copyright
The Copyright of this manual is belonged to Wincode
Ver2.0, November. 2016.
Printed in Taiwan
Trademark
Our registered trademark:
Compliances
CE Class B
FCC Part 15, Class B
CCC, CB
Comply with RoHS regulation

LP4 USER MANUAL
- 3 -
Safety Instructions
Please read the following instructions carefully.
1. Install printer on the flat and stable place. To avoid printer exposed in the
high temperature or high humidity or polluted place.
2. Do not disassemble the printer and adapter under any circumstances.
3. Please check the voltage before printer is connected with power outlet; If
printer is deemed to idle for a long time, please pull out the power cord to
avoid voltage instability to cause printer damage.
4. If printer gets water or conductive material, please shut off the power
immediately to ensure the safety of personnel and equipment.
5. To avoid printer to start printing while there is no label paper installed;
otherwise the print head and platen roller would be damaged.
6. The print head is a thermal part, please do not touch it or its peripherals
during printing or after printing.
7. Shut down the printer when connecting or disconnecting interfaces to avoid
any damage happened.
8. Please choose designated adapter model of Wincode to connect printer
accordingly.

LP4 USER MANUAL
- 4 -
Contents
1. Product Introduction...............................................................................................- 6 -
2. Getting Started ........................................................................................................- 7 -
2.1 Unpacking and checking...................................................................................- 7 -
2.2 Appearance .......................................................................................................- 8 -
3. Setup ......................................................................................................................- 10 -
3.1 Setting up the printer .....................................................................................- 10 -
4. Ribbon Loading......................................................................................................- 11 -
4.1. Ribbon Installation Path.............................................................................- 16 -
5. Label Loading.........................................................................................................- 17 -
5.1 Label installation path................................................................................- 19 -
5.2 Real Time Clock Battery installation .........................................................- 20 -
6. LED indicators and button explanation ...............................................................- 21 -
6.1 LED and button description ...........................................................................- 21 -
6.2 LCD menu description ....................................................................................- 23 -
6.2.1 Menu main framework.......................................................................- 23 -
6.2.2 Application...........................................................................................- 23 -
6.2.3 Setting ..................................................................................................- 24 -
6.2.4 Device...................................................................................................- 25 -
6.2.5 Communication Port...........................................................................- 25 -
6.2.6 File System ...........................................................................................- 26 -
6.2.7 Information ..........................................................................................- 26 -
6.2.8 Upgrade................................................................................................- 27 -
7. WinLabel tool suite ...............................................................................................- 28 -
7.1 WinLabel program includes the below icons ...............................................- 28 -
7.2 Software “WinLabel” installation..................................................................- 29 -
7.3 Driver installation............................................................................................- 29 -
7.4 Update settings and update check................................................................- 30 -
7.5 Driver Setup.....................................................................................................- 31 -
7.5.1 Page Setup ...........................................................................................- 31 -
7.5.2 Media Settings.....................................................................................- 31 -
7.5.3 Sensor Calibration ...............................................................................- 33 -
7.5.4 Options.................................................................................................- 33 -
7.5.5 Tools......................................................................................................- 34 -
7.5.6 About：WinLabel driver version .......................................................- 35 -
7.6 Printer Utility...................................................................................................- 36 -
7.7 Settings page in the Printer Utility ................................................................- 39 -

LP4 USER MANUAL
- 5 -
8. Standalone printing ..............................................................................................- 42 -
8.1. Feature ........................................................................................................- 42 -
8.2. Application..................................................................................................- 43 -
8.3. Hardware notice.........................................................................................- 45 -
8.3.1. Equipment Introduction.................................................................- 45 -
8.3.2. Printer Ports Introduction..............................................................- 46 -
8.3.3. RS-232 pin assignment...................................................................- 46 -
8.3.4. Printer serial port with electronic scales pin assignment ...........- 47 -
8.3.5. Printer serial port with RS-232 scanner pin assignment.............- 47 -
8.4. External device ...........................................................................................- 48 -
8.5. How to contact printer electronic scales .................................................- 49 -
8.5.1. Operating procedures ....................................................................- 51 -
8.5.2. How to make a standalone file......................................................- 52 -
8.5.3. How to download the file to the printer ......................................- 62 -
8.5.4. How to execute standalone file.....................................................- 68 -
8.6. Actual cases using standalone operation.................................................- 70 -
9. Maintenance ..............................................................................................................- 71 -
10. Appendix – LP4A series specification ....................................................................- 72 -

LP4 USER MANUAL
- 6 -
1.Product Introduction
Thank you for purchasing Wincode’s LP4A series label printer, this desktop label printer
with reasonable price has reliable quality to provide user highly-efficient printing
performance. The LP4 series printer not only can print label in text or graphic formats,
but owns basic function and convenient operation interface.
In addition, LP4N series label printer with elegant bright black enclosure has cover
open buffer design to avoid hand clamped in operation; The maximum 5” outside
diameter label loading space; Dual ribbon loading design enables user to use 100m or
300m ribbon; It is also equipped 32 bit processor with highly efficient relevant
configurations to make printing action smoothly and clearly so it can be applied in the
different fields such as retailing, health care, manufacturing, logistics, warehousing
and so on.
The bundled label design program as “WinLabel” provides completed label design
tools and barcode resource for user to design ideal label format; Free database
function can be connected with Excel, Access, Text file…etc and get required
information in the specified positon of label. Standalone function can support
advanced models LP4A series to produce standalone format label.

LP4 USER MANUAL
- 7 -
2.Getting Started
2.1 Unpacking and checking
Unpacking the package, and refer to the below packing list to check whether any part
is damaged or missing in transit. If this incident has been happened, please contact
with local dealer or distributor for further assistance.
Label Printer CD Disc Quick Installation Guide
USB Cable Adapter Power Cord
Ribbon Supply Spindle Empty Paper Core (1” core) 0.5” ribbon cap
Ribbon Take-up Spindle

LP4 USER MANUAL
- 8 -
2.2 Appearance
(Figure 1: Front View)
(Figure 2: Rear View)

LP4 USER MANUAL
- 9 -
(Figure 3: Inside View)

LP4 USER MANUAL
- 10 -
3.Setup
3.1 Setting up the printer
1.) Place the printer on the flat surface.
2.) Make sure the power switch is OFF.
3.) Choose corresponding cable (RS232 or USB 2.0) to connect printer with computer.
4.) Plug the DC power cord into the power slot and plug the AC power cord into a
socket on the wall.
Note: Power Cord instruction
1. To use 100-125 Voltage, please choose minimum rating power cord. (125V, 10A)
2. To use 200-240 Voltage, please choose minimum rating power cord. (250V, 10-
16A)
3. Please select the power cord length less than 2 meter.
4. Power cord is connected with adapter and have to plug in the jack as
ICE-320-C13 as right figure.
Country/ Area
North
America/Taiwan
Europe
China
Power cord
Voltage and
Electricity Spec.
125V, 10A
SVT 18AWG
250V,10A
H05VV-F
250V,10A
RVV H05VV-F
Plug (Refers to the
local plug standard)
125V, 10A
250V, 16A
250V, 10A