Wincor Nixdorf BA72R User manual

BA72R
12.1" TFT LCD Monitor
User Manual

WincorNixdorf PteLtd
2, Kallang Sector
Singapore 349277
Fax: [phone]
http://www.wincor-nixdorf.com

BA72R
BA72R 12.1" TFT LCD Monitor
User Manual
Edition Mar 2004

BEETLE® is a registered trademark of Wincor Nixdorf GmbH
Copyright Wincor Nixdorf Pte Ltd, 2004
The reproduction, transmission or use of this document or its contents is not permitted
without express authority.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or
design, are reserved.
Delivery subject to availability; technical modifications possible.

Contents
MANUFACTURER’S DECLARATION AND APPROVAL........................................3
GENERAL AUTHORIZATION .......................................................................................3
FCC-CLASS ADECLARATION...................................................................................3
TESTED SAFETY.....................................................................................................4
USER INFORMATION................................................................................................4
SAFETY INSTRUCTIONS ...........................................................................................5
POWER CORD SELECTION .......................................................................................6
For the United States and Canada....................................................................6
Outside of the United States and Canada.........................................................7
For the United Kingdom....................................................................................8
INSTRUCTIONS FOR MAINTENANCE ............................................................................9
WARRANTY ...........................................................................................................9
RECYCLING ...........................................................................................................9
INTRODUCTION..................................................................................................11
ADVANTAGES AT A GLANCE....................................................................................12
UNPACKING AND CHECKING THE DELIVERY UNIT.........................................................12
BA72R COMPONENTS .......................................................................................13
SCREEN MODULE.................................................................................................13
POWER ADAPTER.................................................................................................14
CABLES ..............................................................................................................14
CAPACITIVE TOUCH SCREEN (OPTION)....................................................................15
General..........................................................................................................15
Touch Screen and Sleep Mode.......................................................................16
How to Operate..............................................................................................17
Cleaning Instructions ......................................................................................17
RESISTIVE TOUCH SCREEN (OPTION)......................................................................18
General..........................................................................................................18
Construction of the resistive Touch screen......................................................19
How to Operate..............................................................................................19
Cleaning Instructions ......................................................................................19
INSTALLING THE BA72R (TABLE TOP VERSION).........................................................20
SECURING THE SCREENS (TUBULAR STAND VERSION)................................................21

ADJUSTABLE SCREEN ANGLE .................................................................................22
ERGONOMIC TERMINAL WORKPLACE .......................................................................23
INSTALLATION...................................................................................................24
CONNECTING THE VGA CABLE ...............................................................................24
CONNECTING THE TOUCH CABLE (OPTION)................................................................25
CABLE ROUTING ...................................................................................................26
SOFTWARE INSTALLATION......................................................................................27
ON-SCREEN DISPLAY (OSD).................................................................................28
Description of Error Messages........................................................................33
TECHNICAL DATA..............................................................................................34
MODELS .............................................................................................................34
OPERATING CONDITIONS .......................................................................................35
TOUCH SCREEN (OPTIONAL)...................................................................................35
DISPLAY SPECIFICATION ........................................................................................36
DISPLAY MODE ....................................................................................................38
INVERTER (HIGH-VOLTAGE GENERATOR).................................................................39
INTERFACE DEFINITION....................................................................................40
VGA INTERFACE ..................................................................................................40
TOUCH INTERFACE ...............................................................................................41

Manufacturer's Certificate and Notes
3
Manufacturer’s Declaration and Approval
General Authorization
This device fulfills the requirements of Electromagnetic
Compatibility (EEC) standards, 89/336/EEC and 73/23/EEC
"Low Voltage Directive". Therefore, you will find the CE mark on
the device or packaging.
FCC-Class A Declaration
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Le présent appareil numérique ne produit pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de la "classe A" prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.

Manufacturer's Certificate and Notes
4
Tested Safety
The BA72R has been awarded the GS symbol for
"Gepruefte Sicherheit" (test safety). BA72R fulfills the
requirements for ergonomy according to ZH1/618:1980-
10
Additionally, the BA72R has also been awarded to cUL-
and UL-symbol.
User Information
Wincor Nixdorf (WN) does not accept responsibilityfor radio and TV interference
and faults that care caused by unauthorized changes that have been made to the
devices. Furthermore, cables or other devices that have not been approved by WN
may not be connected to the device. The user is responsible for any faults and
interference that are caused as a result.
Repair work on the devices should only carried out by authorized and
specially trained personnel. Improper repairs will lead to the loss of
any guarantee and liability claims.
Extension boards with electrostatically endangered components can be identified
with this label.

Manufacturer's Certificate and Notes Safety Instructions
5
Safety Instructions
This device conforms to the corresponding safety regulations for information
technology devices, including electronic office machines for use in the office
environment.
If the device is moved from a cold environment to a warmer room where it is to
be operated, condensation could occur. The device must be completely dry
before being put into operation. Therefore an acclimatization time of at least
two hours should be accounted for.
Lay all cables and supply lines so that nobody can tread on them or trip over
them.
Data cables should neither be connected nor removed during electrical storms.
Protect the device from vibrations, dust, moisture and heat, and onlytransport
the device in its original packaging (to protect it against impact and blows).
Takecare to ensure that no foreign objects (e.g. paper clips) or liquids can get
into the inside of the device, as this could cause electrical shocks or short
circuits.
In case of emergencies (e.g. damaged housing, liquid or foreign objects
getting into the device), the device should be switched off immediately, the
mains plug of the BEETLE or PC should be removed, and the Wincor Nixdorf
customer service should be contacted.
If the LCD display element is broken and the liquid crystal solution leaks out of
the display and onto your hands, clothing etc, wash your hands or clothing
immediately with soap or alcohol, holding them under running water for at least
15 minutes. If the liquid comes into contact with your eyes, please consult a
doctor immediately.
Generally you should connect IT-devices only to power supply systems with
separatelyguided protective earth conductor (PE), known as TN-S networks.
Do not use PEN conductors! Please also observe the recommendations of
the norm DIN VDE 0100, part 540, Appendix C2, as well as EN50174-2,
§5.4.3.

Manufacturer's Certificate and Notes Safety Instructions
6
Power Cord Selection
The power cord for this unit has
to select according to the country
of destination. It must be used to
prevent electric shock. Use the
following guidelines if it is
necessary to replace the original
cord set.
The female receptacle of the cord
set must meet CEE-22
requirements (see above Figure).
For the United States and Canada
Use a UL listed and CSA labeled cord set consisting of a three-conductor cord
with a maximum length of 15 feet.
For units, which stand on a desk or table, typeSVT or SJT cord sets shall be
used. For units, which stand on floor, only SJT type cord sets shall be used.
The cord set must be selected according to the current rating for your unit. Please
consult Table A for the selection criteria for power cords used in the United States
and Canada.
Table A:
Cord Type Size of Conductors
in Cord Maximum Current Rating of Unit
SJT 18 AWG 10 Amps
16 AWG 12 Amps
14 AWG 12 Amps
SVT 18 AWG 10 Amps
17 AWG 12 Amps

Manufacturer's Certificate and Notes Safety Instructions
7
Use a parallel blade, grounding type
attachment plug rated 15 A, 125 V.
Use a tandem blade, grounding type
attachment plug rated 15 A, 250 V.
Outside of the United States and Canada
Use a cord set consisting of a minimum AWG according to Table A and a
grounding type attachment plug rated 15 A, 250 V. The cord set should have the
appropriate safety approvals for the country in which the equipment will be installed
and should be marked HAR.

Manufacturer's Certificate and Notes Safety Instructions
8
For the United Kingdom
Should the plug on the flexible cord not be of the type for your socket outlets, do
not use an adapter but remove the plug from the cord and discard. Carefully
prepare the end of the supply cord and fit a suitable plug.
WARNING:
THIS APPLIANCE MUST BE EARTHED
IMPORTANT:
The wires in this main lead arecolored in accordance with the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
As the colors of the wires in the mains lead of this appliance may not correspond
with the colored markings identifying the terminals in your plug, proceed as follows:
The wirewhich is colored Green and Yellow must beconnected totheterminal
in the plug which is marked with the letter E or by the earth symbol or colored
Green or Green and Yellow.
The wirewhich is colored Blue must be connected totheterminal which is
marked with the letter N or colored Black.
The wirewhich is colored Brown must beconnected totheterminal which is
marked with the letter L or colored Red.

Manufacturer's Certificate and Notes Instructions for Maintenance
9
Instructions for Maintenance
Clean your BA72R regularly with an appropriate surface cleaning product. Make
sure that the device is switched off, connector cables are unplugged and that no
moisture is allowed to get into the inside of the device.
Please observe the maintenance and cleaning instructions for each of the BA72R
components. These instructions can be found in their respective chapters.
Warranty
Wincor Nixdorf guarantees a limited warranty engagement for 12 months
beginning with the date of delivery. This warranty engagement covers all those
damages that occur despite a normal use of the product.
Damages because of
improper or insufficient maintenance,
improper use of the product or unauthorized modifications of the product,
inadequate location or surroundings
will not be covered by the warranty. All parts of the product which are subject to
wear and tear (e.g. backlight of the LED) are not included in the warranty
engagement. Please order spare parts at the Wincor Nixdorf customer service.
Recycling
Environmental protection does not begin when the time has come to dispose of the
BA72R; it begins with the manufacturer. This product was designed according to
our internal norm “Environmental conscious product design and development”.

Manufacturer's Certificate and Notes Instructions for Maintenance
10
The BA72R is manufactured without the use of CFCs and CCHS and is produced
mainly from reusable components and materials. The processed plastics can, for
the most part, be recycled. Even the precious metals can be recovered, thus
saving energy and costly raw materials.
Please do not stick labels onto plastic case parts. This would help us to re-use
components and material. You can protect our environment by only switching on
your equipment when it is actually needed. If possible, even avoid the stand-by-
mode as this wastes energy, too. Also switch your equipment off when you take a
longer break or finish your work.
Currently at present, there are still some parts that are not reusable. Wincor
Nixdorf guarantees the environmentally safe disposal of these parts in a Recycling
Center, which is certified pursuant toISO 9001.
So don’t simply throw your BA71/BA72 on the scrap heap when it has served its
time, but take advantage of the environmentally smart up-to-date recycling
methods!
Please contact your competent branch or the Recycling Centre Paderborn (for
European countries) for information on how to return and re-use devices and
disposable materials under the following fax number:
Fax. [phone]
Or send us an email to:
[e-mail]
Welookforwardtoyourfaxormessage.

Installation and Securing the Screen
11
Introduction
The BA72R is a new addition to our range of flat-panel display. This display
features a standard analog RGB interfaceallowing connection to PC's CRT output.
There is no need to add a digital graphics adapter. Using the BA72R provides you
with a terminal-orientated, ergonomic and customer-friendly cashier’s workplace.
The BA7R can also be optionally equipped with a Touch Screen. The adjustment
of screen size is a breeze via the OSD (On-Screen-Display) menu.
The display can be applied in all trade market segments like specialist retailers,
departmental stores, self-service stores, petrol stations or in restaurants. There is
indeed a great deal of scope for implementing a BA72R. Introduction
They can be used, for example, as:
an ordering terminal
an information terminal
a lottery terminal
a point-of-sale terminal
a training terminal.
The low-energy, flicker-free and radiation-free colour monitor of the BA72R is an
Active-Matrix-Display in TFT-technology (Thin Film Transistor). Therefore, it is
especially suited for multimedia applications as it offers brilliant colour
representation, a better contrast ratio and a high display speed.
The screens can be installed directly on the cashier’s desk or fastened to a tubular
stand. Furthermore, they can also be set up on the central unit of a modular
BEETLE system.

Installation and Securing the Screen
12
Advantages at a Glance
low footprint
ergonomic terminal workplace
key to customer service
basis for animation and multimedia
flicker-free and freefrom radiation
high resolution
high brightness
very good contrast ratio
high brilliant colours (up to 65538)
wider viewing angle (less glare through crosslight)
Unpacking and checking the Delivery Unit
Unpack the parts and check to see whether the delivery matches the information
on the delivery note. The delivery comprises of the respective screen module.
Controllers and data cables, necessary for operation, can be ordered separately. If
damage has occurred during shipping or if the package contents do not match the
delivery note, promptly inform your Wincor Nixdorf sales outlet. Transport the
device only in its original packaging (to protect it against impact and shock).

Installation and Securing the Screen
13
BA72R Components
Screen Module
The screen module represents the main unit of the BA72R. It comprises of a TFT-
LCD colour screen, the auto-scaling display Controller and an inverter that
generates the voltage for backlighting the screen. As an option the screens are
available with Touch Screen.
Remove the cable cover by pushing
it in the direction of arrow (see
picture) and then taking it off
upwards.
The TFT LCD flat screen is an SVGA-compatible 12.1” that is flicker-free and free
of radiation and has only a low heat emission. The BA72R has a native resolution
of 800 x 600, but it features high-quality advanced auto-scaling display controllers
that allow scale up from VGA and scale down from XGA.
WARNING:
If the display element is damaged and the liquid crystal solution leaks out onto your
hands or clothing, please wash your hands or clothing immediately under running
water for at least 15 minutes, using soap or alcohol. If the liquid comes into contact
with your eyes, consult a medical doctor immediately.

Installation and Securing the Screen
14
Power Adapter
The BA72R is comes with an external AC-DC Power Adapter. The 35W Power
Adapter has an auto-ranging AC inlet accepting input voltage from 100 to 240VAC.
Cables
Standard VGA cable, 1.8m
Touch Cable, 1.8m (option)

Installation and Securing the Screen
15
Capacitive Touch Screen (Option)
General
The TFT Touch Screen works according to the principle of a change in analog
capacitance. It has a glass screen with a transparent, thin-film overlay on the
surface. This is fully sealed and protected by a further layer of clear glass.
Electrodes on the edges of the screen provide a uniform low-voltage field. As soon
as you touch the screen with your finger the contact point is “recognized” by the
change in capacitance. Because this takes place very quickly -15 milliseconds
after being touched -the Touch Screen is optimally equipped for a number of
different requirements and applications.

Installation and Securing the Screen
16
The programming interface of the screen is identical to the mouse interface.
Touch Screen and Sleep Mode
Using the Touch Screen with a BEETLE Pentium CPU, an entry via touch during
sleep mode may lead toa faultyinput. During sleep modenothing can beread from
the LCD flat screen. Entries via touching the screen will still be processed by the
system, but without the system “waking up”.
For these reasons it is not recommended to set the sleep mode. For
details please read the chapter “BIOS Setup” in the BEETLE User
Guide.
!