Wind Crest WER Series User manual

Copyright 2006 Wind Crest by CNP Industries 1
Install Quick Specs are for planning purposes only. Please refer to the detailed installation instructions, prior to
making any cutouts.
Wall Mounted Hoods – Install Quick Specs
WER Series Hoods - 24” Depth
Installation Type & Discharge Direction
Wall – vertical discharge
Discharge Size off Hood Top
14” x 4 1/4” rectangular
Discharge Transition – purchased
separately
See “Ventilation” section for options
Standard Features
•304 Series, 18 gauge stainless steel
•Halogen lighting (dual 50 watt lamps 36” to
48” widths/four 50 watt lamps 60” width –
with Hi/Lo setting
•Dishwasher safe, heavy aluminum mesh
filters
•All Stainless Steel Finish Hoods can be
installed Indoors or Outdoors (see
Installation Instructions)
•Widths: 36”, 42”, 48” and 60”
Finishes
•Stainless Steel (S), White (W), Essence of
Copper (E) and Pewter (P)
Optional Upgrades
•250 Watt Heat Lamp Fixtures (add “H” to
hood model number) e.g. WER364SH
•6” or 12” Canopy Extensions in matching
finish (Model(s): 6EC36S or 12EC36S for
36” wide hood in stainless steel finish).
NOTE: Specify desired canopy height,
width and finish when ordering.
•Chrome or Brass Rolled Pot Rails
(Model(s): ACCBRC or ACCBRB) – indoor
use only
•Stainless Steel Back Splash with drop-
down chrome racks supports a maximum
of 30 lbs. (BS plus width – e.g. BS36)
Hood Carton Weight:
WER364 = 58 lbs. WER484 = 72 lbs.
WER424 = 65 lbs. WER604 = 85 lbs.
widthminus
21"
12"
3"
24"
18"
36,42,48,60"
Wiring Access
1"
14"
C
L
ULUL
LISTED7Z66 C
= widthof hood
13"
WER Hoods
“BS” Warming Shelf
A
ccessor
y
with Chrome Racks

Copyright 2006 Wind Crest by CNP Industries 2
Install Quick Specs are for planning purposes only. Please refer to the detailed installation instructions, prior to
making any cutouts.
Wall Mounted Hoods – Install Quick Specs
WER Series Hoods - 24” Depth (cont.)
Maximum Power Supply Required*
15 Amps @ 120 V AC, 60 Hz
20 Amps @ 120 V AC, 60 Hz (when used with
VEN150E remote ventilator)
*Electrical rating is maximum required for any
combination of ventilator, lighting and heat
lamps.
Outdoor Electrical Requirements
Damp outdoor installations require a fault
interrupter circuit connection.
Hood Lighting Rating
•36” to 48” widths: 100 watts w/halogen
lights or 600 watts w/halogen + heat lamps
•60” width: 200 watts w/halogen lights
or 700 watts w/halogen + heat lamps
Ventilator Options
640 CFM, Internal Blower: VEN060I**
1000 CFM, Remote Blower: VEN100E
1500 CFM, Remote Blower: VEN150E
Ventilator Motor Ratings
VEN060I: 2.8 Amps @ 120 V AC, 60 Hz**
VEN100E: 8 Amps @ 120 V AC, 60 Hz
VEN150E: 12 Amps @ 120 V AC, 60 Hz
**Two VEN060I internal ventilators can be installed
in WER 60” wide hood. This installation requires
part #10220 dual wire harness. Refer to installation
instructions for full details.
Ventilator Dimensions & Accessory
Transitions (see Ventilator section)
CUSTOMER SPECIFICATION:
Hood Width Specified & finish:
(e.g.WER364S)
Add Keep Hot Lamps: (e.g. WER364SH)
Accessories Selected: (e.g. Back splash with
racks, chrome or brass rails, canopy
extensions)
=widthof
6", 12"
12"
hoodtop
Center Support
48, 60" Models
Chrome/Brass
Rolled Pot Rail
1-7/8"
3/4"
Final Hood Model Selected:
Add Any Accessories:
Specify Ventilator Selected & Transitions:
_____________________________________
“EC” Canopy Extensions (6” or 12” height) for WER hoods