Windhager VarioWIN User manual

Quick guide
VarioWIN pellet central heating boiler
Operating phases are displayed
here, including Standby, Burner
OFF, etc.
Menu line
Signal lamp (LED)
„Operation“ – green
Full-text display
(illuminated display)
Assignment of buttons to
their specific function
Manual operation / flue cleaning
function
ON/OFF button
Menu buttons
5s
RESET
Boiler temperature
Standby
Info Menu
38°C
07/2012 092948/02
Ending function: Press the Cancel button or automatically after about 45 minutes.
Chimney sweeper func.
Power 100% 45 min
(Operating phases)
30% Cancel 100%
42°C
(Symbol flashes)
Chimney sweeper func.
Power 30% 45 min
(Operating phases)
30% Cancel 100%
42°C
(Symbol flashes)
Pressing the corresponding menu button enables the boiler to be operated with 30 % (= part load) or 100 % output.
The operating time is reset to 45 min. when the Manual operation / chimney sweeper function button is pressed
again.
Chimney sweeper function
Starting: Briefly press the Manual operation / chimney sweeper funktion button (the lighting/display is switched
on), press the button again briefly, the boiler temperature is set to about 60 °C for 45 min.
Removing ash and cleaning boiler and burner
Note!
The ash may be loaded with heavy metals. Heavy metals may affect soil fertility. Ash is not there-
fore suitable as a fertiliser and should be disposed of with residual waste.
Warning of hot surface: risk of burns!
Before touching these surfaces, you must switch off the boiler and let it cool.
Attention!
Do not open the combustion chamber door during operation. Always switch the boiler off first with
the ON/OFF button and wait until burnout mode has finished.
Risk of fire if ash hasn‘t cooled! Store ash in lockable and non-combustible container on non-
combustible base for at least 48 hours.
InfoWINplus
The lighting/display is initially switched on for 10 min. by briefly pressing a button. The corresponding function is
then started by pressing the button again.
A brief explanation of the most important functions of the operating unit:

The “Clean boiler and burner” cleaning request is displayed
Display on InfoWINplus IN 590 or FE 390
The VarioWIN is equipped with a cleaning interval display. The cleaning request for the combustion chamber and
burner pot is displayed on the InfoWIN and must be reset after cleaning has finished.
Cleaning:
a) Take out the baffle plate and remove the ash (VarioWIN 120 only).
b) Clean fly ash off the thermocontrol sensor with a cleaning brush.
c) Fallrinne reinigen.
d) Clean the burner pot.
e) Empty the ash pan(s) or remove the ash from the heating surface duct
f) Check that there is not too much dust in the VarioWIN reserve supply container and that there is no bridge
formation – remove the dust.
Cleaning the baffle plate
Thermocontrol sensor down chute Thermocontrol sensor
Subject to technical modifications. AWP-vor-übersetzt aus 023824/03
Removing ash
VarioWIN Premium approx. every 400 kg pellets or VarioWIN Exklusiv-S / Exklusiv approx. every 1200 kg pellet
a) Insert the key for manual heating surface cleaning (VarioWIN Premium only) and move it back and forth se-
veral times.
b) Empty both ash pans.
Connect the key and operate it several times Emptying the ash pan
Ash pan for
heating surfaces
Ash pan for
combustion chamber
VarioWIN 120
VarioWIN 120
VarioWIN 060 VarioWIN 060 VarioWIN 120
1...........Cleaning tool and, for VarioWIN 120, removal device for cone
2...........Guide groove for locking the cone in the burner pot
3...........Cone
4...........Primary air pin
5...........Grate plate
6...........Secondary air holes
7...........Lock for cone
8...........Burner pot
Cleaning the thermocontrol sensor and down chute
Resetting the cleaning request
After the combustion chamber and burner pot have been cleaned, the operating hours counter for boiler cleaning
must be reset.
Boiler cleaning
Time
Feed operating mode
Time profile feed
Probe switching
Choose Back
Selecting “Boiler cleaning”
Has boiler and burner cleaning
been performed?
Confirm
Yes Back
Confirming with the Yes button
At least once per heating season
see operating manual.
Press the Reset button or switch on the boiler at
the InfoWINplus. Wait for the self-test to finish,
press the Menu button and change to operator le-
vel. Select the „Boiler cleaning“ sub-menu in the
operator level and confirm by pressing Yes. The
counter is reset.