Windsor PV5 Manual

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com
ELECTRICAL
The Model PV5 Wet/Dry Vacuum
Cleaner operates on standard
15 amp,
120voltA.C. household current 220 volt
option available. Voltages below 105
volts, or above 125 volts, will cause
potentially serious damage
to the vac
motors.
Thirty
- fivefeet of 16/3 STJO cable with
a 3
- prong plug is the power connection
to the machine.
This system has3 mainunits:
1. Cabinet assembly with vacuum
motors, and attached electrical
cable.
2. Dome and perk/filter chamber
and cage.
3. Waste bucket.
Carefully unpack and inspect all com
-
ponents for shipping damage. If you
discover any damage, notify the deliver
-
ing carrier immediately. Your machine
was tested and inspected thoroughly
before shipment, and damage is the re
-
sponsibility of the carrier.
OPERATION
Attach vacuum hose between the wand
and floor
tool and the machine.
FOR DRY PICKUP
The waste bucket MUST have at least
5” of water in it before dry pickup is
started, and the perk/filter chamber
and cage must be inplace.
FOR WET PICKUP
Wet pickup should be done with the
perk/filter chamber and cage inplace.
Insert electrical plug into 115 volt, 15
amp outlet. Make sure the dome is in
place and sealed. You may be working
on wet cerpet or wet floors,
so make
sure the machine is properly grounded.
To preventan overloaded circuit, do not
operate on the same circuit with other
appliances.
Turn power switch ON.
WARNING: When usingfor wet pickup
an overflow of water or dirt into the
vacuum motors can cause them
to fail!!
Constantly monitor the level
of waste
water in the recovery bucket. When
about 2/3rds full, shut off the machine,
remove the dome, take out bucket and
empty. Keep the exterior of the bucket
dry
so no moisture gets into the vacuum
chamber. Replace the bucket, center
and seal the dome and continue
cleaning.
Do not use to pick up volatile materials
or dry chemicals.
Do notexpose the unit
to rain. Always store it indoors.
Do not tip over the machine. Always
operate with vac hose clipped by rope
leash
to the machine.
AFTER CLEANING
Emptythe waste water bucket and rinse
it thoroughly. Wipe out tank. Wipe off
machine and wand with a damp cloth.
Clean lint from the two air screens
inside the vacuum chamber before each
use.
MAINTENANCE
Periodically inspectthe surfaces, hoses,
cable, filters and connections on your
machine. Allsurfaces should beclean
to
minimize abrasion damage. Use only
soap and water for cleaning your
machine.
Do not walk on hoses. Keep
them clean and unkinked. Frayed spots
on hoses should be covered and end
connectors kept snug. Because the
electrical cable will lie on
Wet carpet or
floors at times, the cable must be well
insulated and cable connector screws
should be tight.
Do not walk on the
cable or run machinery over it. If the
cable insulation is broken or frayed,
repair or replace
it immediately. Don’t
take chances with an electrical fire
or
shock.
If necessary, the plastic perk/filter
chamber can be removed for cleaning
by releasing the rod that holds
it in
place. When replacing the chamber be
sure rubber gasket in dome elbow is in
place.
POSSIBLE CAUSE SOLUTION
PROBLEM
No power to machine Dead electrical circuit
Powerswitch failure.
Faulty electrical cable.
Equipmentnotgrounded.
Electricalshock
Motorspeed varies
or doesn’t run
Lossof vacuum
Motor brushes worn.
Motorworn out.
Loosevacuum dome.
Clogged water chamber.
Crack indome or defective
glue joint.
Lintor dirtclogging vacuum
screen.
Loosecuffs onvacuum hose.
Vacuum motorseals leaking.
Floortool vacuum chamber
plugged.
Brokenvac hose.
Damageddome gasket.
Worn out vac motor.
Check building circuit breaker or
fuse box.
Replace.
Replace.
Ground prong on plug broken
off. Never operate machine
with grounding prong removed.
Replace.
Replace.
Center andseal dome over tank.
Rinse outwith water.
Replaceor reseal usingacrylic
plasticcement only.
Withpower off, clean screen.
Tightencuffs turning counter
-
clockwise.
Replace.
Wash outwith hose. Pick lint
outwith wire
Replace.
Replace.
Replace.
I
LIMITED WARRANTY
WINDSOR warrants to the original purchaserluser that
this product is free from defects in workmanship and
materials under normal use and service for a period of
one year from date of purchase WINDSOR will. at its
option. repair or replace without charge, except lor
transportation costs. parts that fail under normal use
and service when operated and maintained in
accordancewith the appl!cable operation and InStrUC-
tion manuals This warranty does not apply to normal
wear, or
to items whose life IS dependent on their use
and care, such as cords. switches. hoses. rubber parts.
electric motor parts. etc
IN ADDITION to the above warranty. for a period of
5 YEARS WINDSOR will. without charge. either re -
place or return to working order. at its option. any solu -
tion tank that fails as a result 01 defects in materials or
workmanship during normal service and usage except
for transportation costs
This limitedwarranty is
in lieu of all other warranties
expressedor implied and releases WINDSOR from all
other obligations and liabilities It is applicable
only in
the
U S A and Canada and is extended
only to the
original userlpurchaser of this’product WINDSOR is
not responsible lor costs for repairs performed by
persons other than those specifically authorized by
WINDSOR This warranty does
not apply to damage
from transportation alterations by unauthorized
persons misuseor abuseof the equipment use of
non
compatiblechemicals or damage to property or loss of
incomedue
to malfunctioningof the product
If a difficulty develops with this machine you should
contactthe dealerfrom whom itwas purchased
WINDSOR INDUSTRIES, INC.
2635 So Santa Fe Drive Denver CO 80223
303’777-7774

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com
KEY AMT. PART NO. DESCRIPTION
1 1 10-157MCHD Base - PV - 5
- - -
2 1
72-003 Tank Cabinet A SS ~. - PV - 5
3 1
10-159MCHD TankTopABS
4 1
10 - 162 Perk/Filter Chamber PV - 5
6' 1 20-128 Electric Cord 16 - 3x35'
Dome, PV - 5
Cord Cap 120V - 3 - Wire
5.r 1 10-168
_.
-
7 1 21 - 027
PERK/FILTER VAC MACHINE BREAKDOWNAND PARTS LISTING
U
,
6&-
J
v
ED
I w
ASSEMBLE
ASS-LE- =-
8 1
22 - 026 Lead Assy. Switch PV - 5
9 1
22-025 Lead Assy. Vacuum Motor
Rocker Switch
10 1 21 - 072
11 1 21 - 081 Strain Relief w/Spring
12 1 50 - 024 Vacuum Motor Gasket 7.5 " Dia.
Gasketseal. VacMotor-l/Exll/lG
Vacuum Motor, Tangential 220V PV - 5
13 2 50 - 005
14 2 25-051 Vacuum Motor 12OV
15 2 30 - 001 Wheel, 6~1%
16 2 30 - 002 Caster, 3 x 1 Vi
17 2 30 - 046 Screen - Vacuum Intake 1% Dia.
18 4 33 - 010
19 4 33-013 Hexnut Vi - 20
14A 2 25 - 001
Screw, Vi -20~5% HHMSPlated
.. ..
20 1 33 - 015 Bolt. Vi - 20 x 2. I - Bolt
55 1
06-004 Squeegee Shoe for 106-003
56 1
06-006 Carpet Shoe for 106-003
57 1
06 - 003 Master Floor Tool Head
~~
58 1 06-009 Upholstery Twl PV - 5
PERK/FILTER VAC
WIRING SCHEMATIC
VACUUM MOTORS
<J
R OC KE R swim
6 MONTHS OR 750 OPERATING
HOURS
Removing Waste Water Cabinet As -
sembly From Base:
1. Disconnect machine from power
source.
2. Removethe handle
3. Turn machine upside down and
remove thetwo lock nuts from the
bolts coming through the casters
(one
on each caster).
4. Remove base from cabinet and
disconnect leads at the molex
connector.
1. To removevac motors, disconnect
wires and remove three
1/" hex-
nuts.
2. Lift out vac motors being careful
not to damageseals
3. To inspect brushes: remove
brush holddowns. New brush
length is
1 " . Brushes should be
replaced when they reach
318"
length or after 750 operating
hours.
4. Inspect vacuum intake opening
for lint. If there are large accum
-
ulations, thefan section should be
disassembled and cleaned. Note:
Vacuum motors
can usually be
repaired, but such repairs should
always
be done by a qualified
vacuum repair shop.
VACUUM MOTOR
-_bJ__. . ,... ,. _. . __x
-.

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com
PRODUCT MODIFICATION - Dome Assembly-Perk/Filter Vac
Your new Perk/Filter Vac is equipped with newly designed
dome and hose assemblies. This notice should be retained
with your Dealer Manual for reference when ordering replace
-
ment parts inthe future.
NOTE: Part #lo-168 Dome/Hose Adapter Assy - PV - 5 includes
both sub assemblies
#28-006 and #28-008. For replacement,
individual parts or assemblies can be ordered as shown on
parts list.
I
2
I
I
n 7
I DOME ASSEMBLY I
I
W
6
I I
KEY PART NO. DESCRIPTION
I
10-168 Dome/Hose Adapter Assy
- PV - 5
1 1 28407 Dome
. __ - - . - - .. . -
2 57407 Nut, 1 YZ " Flange
I 3 86401 HoseAdapter
12 40 - 044 HoseAssy w/tag Cord PV - 5 Vac
I 13 87 - 009 Taa Alona Cord Assv. PV - 5
W1982