Wine racks America 6 Column High Reveal User manual

*Please verify that you have the correct number of parts before proceeding.
Depending on the model you purchased, your bundle should contain the following:
Package Contents tools for assembly
Package Contents tools for assembly
4 and 6 Column High Reveal
Assembly GUIDE Page 1
or visit
wineracksamerica.com
Questions?
888.373.6057
END LADDER (X2)
WOOD SCREWS
FINISH NAILS
WOOD PUTTY
MIDDLE LADDERS
DISPLAY TRAYS
STANDARD CONNECTOR (X3)
SCREWLESS CONNECTOR (X2)
REVEAL CONNECTOR (X1)
Cordless Drill Finish Nailer
Hammer Nail Setter
+
Screwdriver
Required
Wood Glue
Suggested
SIDE DISPLAY PIECE
(OPTIONAL)
*All models follow the same assembly procedure varying only in the number of middle ladders your rack will require.

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
4 and 6 Column High Reveal
Page 2
1. Find an open, flat area in which to work. Carefully remove all components from the box and remove banding
with a utility knife. Check the parts list to verify package contents.
2.
Arrange the end ladders on the floor so that the bottle support pieces face one another. Align the large gaps on
each end ladder. The end with the larger gap is the bottom of your rack. Attach a standard connector to the top
and bottom of your rack using the screws provided. Make sure the connectors are flush with the top and bottom
of your rack. (figure 1)
Bottom of rack
1
BEGIN WITH BACK
OF RACK
3. Insert the middle ladders and finish securing the top & bottom connectors using the screws provided. (figure 2)
2
FINISH SECURING BACK
CONNECTORS
Bottom of rack

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
4 and 6 Column High Reveal
Page 3
4. Secure the remaining standard connector so that the top of the connector is 6" from the bottom of the rack.
(figure 3)
Bottom of rack
3
ATTACH REMAINING
STANDARD CONNECTOR
5. Flip the rack over and attach a screwless connector to the top of the rack (figure 4). Attach the remaining screwless
connector so that the bottom of the connector aligns with the bottom of the middle ladder risers (figure 5). Secure
the bottom reveal connector to the bottom of the two end ladders (figure 6).
High Reveal Racks are designed to show no visible hardware on the front of the rack. Use one of these following
methods to install the screwless connectors:
6"
For no visible hardware, add wood glue to the inside of each connector notch. Place the connnector on your
rack and carefully press each notch into place. Hold until glue is dry. (figure A)
For minimal visible hardware, add wood glue to the inside of each connector notch. Place the connector
on your rack and carefully press each notch into place. Hold until glue is dry. For added support, use a finish
nailer to attach the connector to the two end ladders and one middle ladder. (figure B)
For a professional installation, secure the connectors using a finish nail gun to drive a nail through the connector
into each vertical ladder. If you do not have a finish nail gun, drive one of the provided finish nails into each
vertical ladder until it is flush. Then, countersink the nail using a nail setter until the head of the nail is about
1/16" below the surface of the wood. Use provided wood putty to fill nail holes. (figure C)
A B C
+
++
or
A
B
C

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
4 and 6 Column High Reveal
Page 4
6. Stand your rack upright. Secure the display trays to the rack by adding a bead of wood glue to each of the two
grooves on the back of the tray. Set the tray into place so that grooves rest on the lower reveal connector and the
standard connector on the back of the rack. (figure 7)
4
SECURE SCREWLESS
CONNECTOR TO TOP
5
SECURE SCREWLESS
CONNECTOR TO MIDDLE
6
SECURE REVEAL
CONNECTOR TO BOTTOM
7
SECURE DISPLAY
TRAYS TO RACK

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
4 and 6 Column High Reveal
Page 5
7. If you purchased a Side Display High Reveal Rack, secure the side display piece to the rack by adding a bead of
wood glue to each of the two grooves on the side display end pieces. Set the side display piece into place so that
grooves rest on the lower reveal connector and the standard connector on the back of the rack. (figure 8)
8
SECURE SIDE
DISPLAY TO RACK
(OPTIONAL)
8. That’s it!! Place on top of your base rack of choice and enjoy. Pair with other racks for a true wine cellar look.
Side Display Piece
WINERACKSAMERICA.COM
360 North 700 West Suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
Once again, thank you for your business. Remember, customer
service is available to answer any questions Monday-Friday
7:00 am - 5:00 pm MST. Please feel free to contact us for any
wine storage needs.
We would love to see your wine racks in use! Please feel free to
send any photos of your racks to [email protected]