Wine racks America Full Height Diamond Bin User manual

*Please verify that you have the correct number of parts before proceeding.
Depending on the model you purchased, your bundle should contain the following:
Package Contents
Package Contents tools for assembly
Full Height Diamond bin
Assembly GUIDE Page 1
or visit
wineracksamerica.com
Questions?
888.373.6057
77 1/8"
Cordless Drill Finish Nailer
Hammer Nail Setter
Rubber Mallet
Wood Glue
Required
Suggested
Screwdriver
+
END LADDER ASSEMBLIES (x2)
23 15/16"
MIDDLE SUPPORT (x8)
STANDARD CONNECTOR (x6)
24 13/16"
SCREWLESS CONNECTOR (x2)
24 13/16"
WOOD SCREWS
FINISH NAILS
WOOD PUTTY
“X” ASSEMBLY (x3)

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Page 2
Full Height Diamond bin
1. Find an open, flat area in which to work. Carefully remove all components from the box and remove banding
with a utility knife. Check the parts list to verify package contents.
1
BEGIN WITH BACK
OF RACK
* Minimize the risk of splitting your ladders by drilling a 1/16" pilot hole before driving the wood screws.
For best results, drive the screw most of the way in with your drill, then finish tightening by hand.
2. Orient the two side ladder assemblies on the floor as shown, then attach 4 standard connectors to the end ladders
using the screws provided. The top & bottom connector should fit flush with the top & bottom of the rack. This will
be the back of your rack. (figure 1)
3. Flip rack over and attach a standard connector to the top and bottom of your rack using the screws provided.
(figure 2)
Top of rack
2
FRONT OF
RACK

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Page 3
Full Height Diamond bin
4. Attach the middle screwless connectors so that the top edge of the connectors fit flush with the ladder support
pieces on each vertical ladder. Make sure the rack is flat on the floor while attaching the screwless connectors.
(figure 3)
Secure the screwless connectors using a finish nail gun to drive a finish nail through the connector into each
vertical ladder. Use wood glue for added support. (figure 4)
If you do not have a finish nail gun, drive one of the provided finish nails into each vertical ladder until it is flush.
Then, countersink the nail using a nail setter until the head of the nail is about 1/16" below the surface of the wood.
Use wood glue for added support.
3
ATTACH SCREWLESS
CONNECTORS
5. Fill the nail holes using the wood putty provided. Simply push the putty into each hole using your thumb and wipe
excess putty off the surface using a damp cloth.
or
finish nail
(included)
4
SECURE WITH
FINISH NAILS
56
SECURING THE
MIDDLE SUPPORTS
6. Place a dab of wood glue into each notch in the riser supports. (figure 5)
Place the eight 23 15/16" middle supports into place so that each edge of each middle support is flush with the
edge of each riser support. (figure 6)

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Page 4
Full Height Diamond bin
7. Insert the three X assemblies. The fit should be snug, not loose. Carefully work each corner into place until the
assembly is seated all the way in. (figure 7)
*DO NOT push on the center of the X
If necessary you may need to lightly tap the 4 corners of the X Assembly with a rubber mallet. (figure 8)
8. If you are planning to use this rack with our Top Cap shelving system, you’ll need to remove the top two 9 3/4"
riser supports and two 23 15/16" middle supports from the top of your rack so that the shelving can seat
properly along the top of the rack. You can re-sturdy the rack by driving screws down into the rack from
above the Top Cap shelving system. (figure 9)
1
3
4
2
8
7
INSTALLING THE
“X” ASSEMBLIES
9
TOP CAP SHELVING
fully assembled
front view

Assembly GUIDE or visit
wineracksamerica.com
Questions?
888.373.6057
Full Height Diamond bin
Page 5
9. Attaching your rack to the wall (optional). Depending on how many bottles you store, your wine cellar rack
could weigh as much as 540 lbs. To avoid tipping, attach your rack to the wall using one of the following
methods.
1. Put the rack in the desired location.
2. Shim the front of the rack so it is
parallel with the wall behind it.
3. Locate a wall stud behind the rack.
4. Drive a 2 1/2" wood screw through a
back spacer bar to attach to the stud.
1. Use "L" brackets (located at any hardware store).
2. Attach to both the rack and the wall in any out of
the way spot.
WINERACKSAMERICA.COM
360 North 700 West Suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
Once again, thank you for your business. Remember, customer
service is available to answer any questions Monday-Friday
7:00 am - 5:00 pm MST. Please feel free to contact us for any
wine storage needs.
We would love to see your wine racks in use! Please feel free to
send any photos of your racks to [email protected]
10. That’s it! Enjoy this beautiful rack with your favorite beverage. Pair with other rack styles for an ultimate cellar
storage look.