Wine racks America WRA61440 User manual

Questions?
Toll free 1-888-373-6057 or visit www.wineracksamerica.com
Thank you and CONGRATULATIONS for
purchasing this quality product. Properly
assembled, your racking will beautifully
enhance your wine collection for many
years to come. To assemble, please check
to ensure all necessary parts are included
and follow the assembly instructions
closely. If you have any questions or
problems please call customer service toll
free 1-888-373-6057 Monday through
Friday 7:00 am - 5:00pm MST.
[x2] Full Length Vertical Ladder Assembly
[x14] Middle Support
23 15/16"
[x9] Standard Horizontal Connectors
24 13/16"
[x5] Screwless Horizontal Connectors
24 13/16"
PARTS LIST
Planning to stain?
For best results we recommend
you stain or finish your racking
BEFORE assembly.
77 1/8"
Tools For Assembly:
OR +
Finish Nailer Hammer Nail Setter
[x18] 1 1/4" WOOD SCREWS
[x10] FINISH NAILS
Cordless Drill Utility Knife Screwdriver
SMALL BAG OF
WOOD PUTTY
ASSEMBLY INSTRUCTIONS
Rectangular Bin / Case Rack
WRA61440, WRA61441, WRA61442

1. Find an open, flat area in which to work.
Carefully remove all components from the
box and remove banding with a utility knife.
Check the parts list to verify package
contents.
2. Orient the two vertical ladder assemblies
on the floor as shown, then attach 7 standard
horizontal connectors to the vertical ladders
using the 1 1/4" screws provided. The top &
bottom connector should fit flush with the top
& bottom of the rack. This will be the back
of your rack. (figure 1)
Note: The top connector will not line up with
the ladder support piece near the top of the
rack. It should be flush with the top of the
rack and sit about 3/8" above the support
piece. This is to allow for easy install of our
top shelving in our trim-kit system. (figure 2)
*Minimize the risk of splitting your side ladders by
drilling a 1/16" pilot hole before driving the wood
screws. For best results, drive the screw most of
the way in with your drill, then finish tightening by
hand.
3. Flip rack over and repeat step two for securing
the remaining 2 standard connectors to the
top and bottom of the front of your rack.
(figure 3)
* PLEASE FOLLOW WRITTEN INSTRUCTIONS CAREFULLY
1
BACK OF
RACK
3
FRONT OF
RACK
2
TOP OF RACK
LADDER
SUPPORT
PIECE

6. Place a dab of wood glue into each notch of the ladder support pieces. (figure 6)
Place the (14) middle supports into place so that each edge of each middle support is flush with the
edge of each ladder support. (figure 7)
6 7
SECURING THE MIDDLE SUPPORTS
4
ATTACH THE SCREWLESS
CONNECTORS
or
finish nail
(included)
5
SECURE WITH
FINISH NAILS
4. Attach the middle screwless connectors so that
the top edge of the connectors fit flush with the
ladder support pieces on each vertical ladder.
Make sure the rack is flat on the floor while
attaching the screwless connectors. (figure 4)
Secure the screwless connectors using a finish
nail gun to drive a finish nail through the connector
into each vertical ladder. (figure 5)
If you do not have a finish nail gun, drive one of
the provided finish nails into each vertical ladder
until it is flush. Then, countersink the nail using a
nail setter until the head of the nail is about 1/16"
below the surface of the wood.
5. Fill the nail holes using the wood putty provided.
Simply push the putty into each hole using your
thumb and wipe excess putty off the surface
using a damp cloth.

fully assembled
front view
Once again thank you for your business. Remember,
customer service is available to answer your questions
M-F 7:00 am - 5:00 pm MST. Please feel free to contact
us for any wine storage need.
360 N 700 W suite F • North Salt Lake, UT 84054
(toll free) 888-373-6057
(fax) 801-936-0534
WineRacksAmerica.com
7. Stand your rack upright. Anchor the rack to a
stabilizing surface (wall, ceiling, another rack)
by driving two or more 2 1/2" screws through
one or more of the connectors. (figure 8)
8. That’s it! Enjoy this beautiful rack with your
favorite beverage. Pair with other rack styles
for an ultimate cellar storage look.
8
SECURING YOUR RACK TO THE WALL
(top of rack)