Wingsland Minivet User manual

Product manual
1, Introduction
Support and Service
Thanks for your choice for Minivet multi-axis aircraft, in order to make it
convenient and correct for you to use our product, please read the manual
carefully. If you face some difficulties when using products, please contact our
distributor or Wingsland Service Center by email or telephone.
Wingsland service center:
Email address: [email protected]
Tel: 0086-0755-23123452
Danger: Incorrect operation may will casualties.
Warning: Incorrect operation will casualties or will harm human body.
Caution: Incorrect operation will cause harm with less possibility to user,
but with a risk of being injured.
2, Before Using Product (read the instructions before first flight)
Disclaimer & Warning
Attention please read this disclaimer carefully before starting your pilot
experience. Thank you for your using Wingsland product, you hereby agree
with and accept the terms of this disclaimer and it is believed that you have

read it seriously.
This product is not designed or suitable for people under age of 18.
Please make sure that you are responsible for your any flight conduct and
content, or any consequence caused by your flight while using this
product. The product built-in autopilot system causes danger even if we
have made its operation. Good practice before your flight with removing
all propellers.
Please fly in an open area/outdoor and far away from any obstacles and
passengers. You agree to use this product in accordance with local
regulations, terms and any applicable polices and guidelines. Ensure
using this product only for the purposes that are proper.
Any part of this disclaimer is subject to change without notice, please visit
www.szsungreen.com for the latest version for your reference.
This disclaimer is made in various versions of in different languages . In
the event of divergence among different versions, the Chinese version
shall prevail in China domestic area, the English shall prevail in other
countries and areas.
Instructions & Cautions
Ensure using with genuine Wingsland accessories to get most efficiently
flight experience.

Please uninstall all propellers before your calibration or parameters
setting.
Ensure that you are familiar with your local laws, administrative rules and
social habits and agree that you are solely responsible for your own
conduct and content while you fly.
Ensure to check all connections and every part of product is in normal
condition before each flight..
Stay away from obstacles, passengers, crowds, high-voltage line, other
possible sources of electromagnetic interference and fragile goods.
Check that the position of switches of Remote Controller is correctly set.
Ensure the installation of propellers is correct.
Check that the Remote Controller Battery, Intelligent Flight Battery,
Display Screen Battery is fully charged.
Do not fly near the areas existed magnetic or radio interference. For
example, radio and TV tower, high-voltage lines, communication base
station, radar instruments, etc.
Battery Usage Notes
Please keep the battery storage in out of the reach of children.
Do not put the battery into the fire or store in high-temperature
environment.

Battery charging uses the genuine Charger supplied by Wingsland is
demanded. Never charge batteries unattended. Check the battery
condition during your charging.
Attention please to the battery positive and negative. To avoid that the
battery storage in contact with any conductor.
Do not drop or strike battery. Do not use a swollen, leaky or damaged
battery.
If found the battery leakage, do not contact with skin and eyes, if you do
contact, immediately rinse with plenty of water and seek medical help.
The battery level will be effected when using in a low temperature or a high
temperature.
Please do not arbitrarily discard battery ,to dispose of the battery in
accordance with local regulations when the battery is no longer in use.
Discarding battery arbitrarily would cause a fire hazard, and may pollute
the environment.
Ensure that the usage of battery strictly abide by Wingsland User Manual.
Limitation of Liability
Wingsland accepts no liability for damages, injuries or any legal
responsibilities incurred directly from the use of this product in the following
conditions, and this limitation of liability applies to Wingsland suppliers, dealers
and service provider:

Any more you paid in amount for this product than the actual purchase
price.
Any costs and expenses with access to alternative goods, services or
rights.
Costs, expenses increased , loss caused by the data loss, data corruption
or data interruption.
Any loss caused by the violation of the provisions of local laws and
regulations or the civil aviation administration laws.
Any loss caused by the usage of product without abiding by the User
Manual.
Any loss cause by the age, physical and mental condition of the Operator
who is not in the proper condition.
Damages, injuries or any legal responsibilities caused by using the third
party alternation products or fake Wingsland products.
Any loss caused by improper use in a strong magnetic field or in the bad
environmental conditions(such as in the temperature higher than 40
degrees or below 0 degrees Celsius, and in the wind over force 4, etc.)
Any loss caused by Force Majeure,
3,Install Remote Controller Battery
Set switch L1(Figure 2) and switch L2(Figure3) to the middle position.

Install 6s AA Alkaline Battery into the battery compartment on the back of the
Remote Controller. Pay attention to positive and negative.
When using the remote controller, please put the antenna to figure 4
position (horizontal) to the left
4, The Remote Controller component name

5, Remote Controller
Minivet remote controller works with 2.4G frequency and 10 channels, not
only can control aircraft, but also gimbal and camera, thus user can finish all
performance operation without leaving remote controller.
(1)Install Battery
Remote controller uses 6 alkaline batteries. Open battery cap, fix them into
remote controller, and cover back cap.
(picture shows how to open battery back cap and the effect of installing
battery)
Warning: Use the same brand battery please.

Warning: Do not mix new and old batteries together.
(2)Remote Controller Operation
1Turning Remote Controller On and Off
On: Press Power Button to turn on the remote controller, red status LED will
blink.
Off: Press Power Button to turn off the remote controller, red status LED goes
out.
Warning: Remote controller beeps, over low voltage, alter a new battery

immediately.
Warning: Check positions of antennas and switches before turning on
remote controller.
Warning: Turn on remote controller first before inserting flight battery,
after taking out battery then turn off remote controller.
L1 Mode Switches (3rd gear)
L1-Middle: GPS Stabilization Mode, 2 situations below
A In the outdoors with strong GPS signal (more than 6 satellites), GPS
Stabilization Mode .
Bin the indoors with little GPS signal (less than 6 satellites), common
Stabilization Mode .
L1-1:RTH mode
L1-2: Manual Mode
Warning: Beginners do not use manual mode.
L2 assistant mode switch (3rd gear)
L2-Middle: Turn off the assist mode
L2-1: Orientation Lock Mode
L2-2: Point of Interest Surrounding Mode
(3)Gimbal control Joysticks

To be used control gimbal’ pitch
(4) Trimming Button
Trimming Button is used to adjust left and right control stick middle point, when
control stick middle point is calibrated by a computer, trimming adjustment is
no need .When control stick middle point is tilt and out of control by computer,
Trimming Button will work.
When aircraft works with GPS stabilization mode, hovering position will tilt from
hovering point, adopts Trimming Button until aircraft does not tilt from hovering
point. For example, if aircraft tilts from the head, Trimming Button should be
adjusted backward.
Trimming Adjustment Max: any trimming adjustment channel has max value,
when reaches this max value, remote controller will beep quickly twice..
Trimming Adjustment Middle Point: press trimming key into Middle Value,
beep slowly twice, and it will not bring any effect on the responding control
stick channel. When calibrating remote controller middle point, middle value
must be needed.
Warning: When starting trimming adjustment, land aircraft, after
adjusting, fly again to check effect.
Warning: After adjusting remote controller middle point through
Trimming Button, lock it to avoid being touched.
Warning: Suggest user calibrating remote controller middle point by

computer, do not use Trimming Button to adjust middle point unless
emergency conditions.
Trimming Button is locked default thus users will not touch it carelessly.
Trimming Button Unlock Methods:
A Make sure aircraft is powered off B Remote controller is turned off C Press
down 2 Trimming Buttons simultaneously D Powered on remote controller E
When hearing beeping sound twice ,unlock trimming adjustment is finished.
Key Pushing Methods in the picture
Trimming Button Lock Mode: finish the unlock trimming adjustment again
(5)Compliance Version
Remote controller has been set well frequency with receiver when resetting

from factory, but when changing remote controller or receiver, Compliance
Version should start again.
Methods below:
A Aircraft is powered off B Remote controller is turned off C Press 2 Trimming
Buttons simultaneously as the picture shows D Powered on remote controller
E Once Power Status LED blinks quickly release the trimming button F
Powered on aircraft G Remote controller Status LED stops blinking ,keep
long light to finish compliance version.
(6)Operating Aircraft
Control can be set to Model2 or Model 1, and can be switched by buttons,
default set is Model2.Here are 2 models operation methods.
Quick start guide have model2 and model1, model1: right hand control
accelerator up and down, left and right mean move to the left and right; left

hand controls up and down, forward and behind, left and right mean left spin
and right spin.
American hand
Japan's hand

When the aircraft fixed-point hovering will deviate from the hovering,
neutral point need to recalibrate the remote control
Using automatic return mode, must ensure that the return path and no
obstacles around the landing site
(7)Remote Controller Operation Mode(model1 and model2)Switch
A Aircraft is powered off B Turn on remote controller C Press 4 trimming
buttons simultaneously D A A beep shows Model2, twice beep show Model1
Caution: After switching models, suggest calibrating Throttle middle
point by computer.
(8)Remote Controller Indicating Information

Icon arrange contents below
Power LED Status
Slid On Work Mode Quick Blink Compliance Version
Sound Indicate
Powering on remote controller with beep, remote controller start working,
continuous deeps, over low voltage of remote controller, battery need to be
replaced.
Reduce trimming adjustment lock, a beep
Start trimming adjustment lock, a beep
Model2 and Model1 switches, a beep.Model2,beep twice,Moedel1.
Trimming adjustment, a beep trimming adjustment changes, quickly beep
twice, and reach max value, slowly beep twice, trimming adjustment reach
middle value

Statement
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwo
conditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust
accept
anyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliance
couldvoidtheuser'sauthoritytooperatetheequipment.
NOTE:Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfora
ClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsare
designedtoprovidereasonableprotectionagainstharmfulinterferenceina
residentialinstallation.Thisequipmentgenerates,usesandcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instructions,maycauseharmfulinterferencetoradiocommunications.However,
thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.
Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,
whichcanbedeterminedbyturningtheequipmentoffandon,theuseris
encouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing
measures:
‐‐Reorientorrelocatethereceivingantenna.
‐‐Increasetheseparationbetweentheequipmentandreceiver.
‐‐Connecttheequipmentintoanoutletonacircuitdifferent
fromthattowhichthereceiverisconnected.
‐‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
FCCRFwarningstatement:ThedevicehasbeenevaluatedtomeetgeneralRFexposure
requirement.Thedevicecanbeusedinportableexposureconditionwithoutrestriction.
Other manuals for Minivet
2