Wintec Lp-301 User manual

Instruction Manual

User Manual applied to :

LP-301 UHF FM Transceiver VHF FM Transceiver LP-301 programming software:WPS-301

《regulations of radio management of the People's Republic of China》rule:The units and individual who

use the radio equipment in the People's Republic of China,must apply for and get the Radio license from

the Radio management institutions.

CAUTION: when programming the transceiver,read the factory initial data rst,then

rewrite the frequency and signialing etc.,otherwise errors may occur because of different

frequency band etc.

Thank you very much for choosing our transceiver. transceiver provides you with reliable, clear and efcient communication

service.

The transceiver introduces innovative DSP (Digital Signal Processing) baseband processing system to achieve high-

delity voice processing and encryption,it boasts best stability and reliability .With fashionable design and smooth exterior

lines,PL-301 boasts loud and nice timbre,high power,long distance communication,high capacity battery,long standby

time plus optional built-in bluetooth function.It is a cost-effective and multi-functional professional transceiver which meets

needs of every walk of life. It is convinced that you will be satised with this transceiver's quality and functions. For your full

comprehension of the various excellent functions and maintenance, please read the user manual before use.

NOTE

SAFETY INFORMATION FOR USER

transceiver is excellently designed with advanced technology. Please observe the following precautions to perform

your obligation, prevent personal injury and ensure the safety of transceiver usage.

Keep the transceiver and accessories away from children.

1.

Please do not try to open or modify the transceiver without permission, non-professionals process may also cause damage.2.

Please use assorted battery and charger to avoid damage.3.

Please use assorted antenna to ensure the communication distance.4.

Please do not expose the transceiver to long period of direct sunlight, nor place it close to heat appliances. 5.

Please do not put the transceiver in excessively dusty or humid areas. 6.

Do not use harsh chemicals, cleaning solvents to clean the transceiver.7.

Do not transmit without antenna.8.

When using this transceiver, we recommend transmitting for 1 minute then receiving for 4 minutes. Continuous transmitting 9.

for long time or working in high power will heat the back of the transceiver. Do not place the transceiver's hot back close to

any surface of plastic.

All tips above apply to accessories of your transceiver.If any debice can not work normally,please contact

lcoal dealers .If you use any accessories made by other companies, company does not

guarantee the operability and saftey of the transceiver .

ATTENTION

If any abnormal odor or smoke detected coming from the transceiver, turn off the power and take off the battery pack and its

case .Then contact local dealers.

10.

I

CONTENT

UNPACKING �� 01

Supplied accessories chart �� 01

STANDARD ACCESSORIES/OPTIONAL ACCESSORIES �� 02

Standard accessories �� 02

Optional accessories �� 02

BATTERY INFORMATION�� 03

Charging Operation �� 03

Battery Charger Type �� 03

Notice for Charging Battery�� 03

How to Charge �� 04

Normal Charging Tips �� 05

How to Store the Battery �� 05

PREPARATION�� 06

Installing / Removing the Li-ion Battery�� 06

Installing / Removing the Antenna �� 06

Installing / Removing the Belt Clip�� 07

Installing the Additional Speaker/ Microphone (Option) �� 07

GETTING ACQUAINTED�� 08

LCD Display �� 08

Front Panel�� 09

Side Panel�� 10

BASIC OPERATION�� 11

Turn on/off Transciver �� 11

Adjusting Volume�� 11

Operating mode switch �� 12

Channel selection �� 12

Prority Channel�� 12

Prority Channel Setup�� 12

Frequency adjustment �� 13

Frequency input by keypad �� 13

Channels input by keypad�� 13

Squelch off /Momentary Squelch off �� 14

II

CONTENT

Receiving �� 14

Transmitting�� 14

Side key [PF1] function introduction �� 15

Side key [PF2] function introduction �� 15

Scan function�� 17

Turn on/off radio function �� 17

Delete/Add FM Radio�� 18

FM radio scan�� 18

Frequency copy�� 18

SHORTCUT FUNCTION SETUP �� 19

Editing Channels �� 19

Delecting Channels�� 19

Copying Channels �� 19

Offset frequency setup�� 19

Squelch levels setup�� 20

High and low power setup�� 20

CTCSS/DCS Encode Setup�� 21

Offset frequency direction Setup �� 21

Frequency Step size setup�� 22

CTCSS/DCS Decode Setup�� 22

VOX On/Off �� 22

Frequency reverse�� 23

DTMF Code Selective�� 23

DTMF Code Transmitting �� 24

Remotely kill/waken�� 24

Remotely stun/waken�� 24

Channels scan skip�� 25

Frequency/channels scan �� 25

Switch Between VFO and Frequency +Channel Mode�� 26

Keypad Lock�� 26

FUNCTION MENU SETUP �� 27

Squelch Level Setup�� 27

III

CONTENT

High and low power setup�� 27

CTCSS/DCS encode setup�� 28

CTCSS/DCS decode setup�� 29

Offset frequency direction Setup �� 29

Frequency Step size setup�� 30

Frequency reverse�� 30

Voice operated Transmission (VOX) Setup�� 31

VOX Level Setup�� 32

VOX Delay Setup �� 32

Non-signaling Tail Tone Elimination �� 33

PTT Key Voice Prompt�� 33

Frequency Reverse Setup �� 34

The Automatic Shutdown Time Setup�� 34

Vox Beep Setup�� 35

LCD Backlight Setup�� 35

FM Radio Return Time setup �� 36

Battery Save Setup�� 36

Scan Dwell Time Setup�� 37

Time-out-Timer �� 38

Offset Frequency Setup �� 38

DTMF Group Code Setup �� 39

DTMF Turn On Time setup �� 39

DTMF Turn Off Time setup�� 40

Noise Reduction Function Setup �� 40

Busy Channel Lock�� 41

Display Mode Setup�� 41

Editing Channel Name�� 42

Turn On /Off Optional Signal �� 42

Signaling Relations Setup�� 43

Wide/Narrow Band Setup�� 43

Function Icon Dwell Time Setup�� 44

Current Battery Voltage Enquiry �� 45

IV

Starting Display Setup �� 45

Display Character Dened By User �� 46

PROGRAMMING SOFTWARE STARTING(TAKES WINDOW XP FOR EXAMPLE)�� 47

TECHNICAL SPECIFICATIONS �� 48

TROUBLE SHOOTING GUIDE ELIMINATION METHOD�� 49

ATTACHED CHART 1�� 50

CTCSS Frequency Chart �� 50

ATTACHED CHART 2�� 51

DCS Frequency Chart�� 51

CONTENT

01

UNPACKING

Please carefully unpack the transceiver.We recommend that you identify the items listed in the following table before discarding

the packing material .If any items are missing or have been damaged during shipment ,pls contact with dealers immediately.

Supplied accessories chart

Item Number Quantity

Antenna VHF(135-175MHz) 1

UHF(400-480MHZ) etc� 1

Li-ion Battery BT FR30 LI 1

Battery Charger L CHG 30B 1

AC adaptor ADA 12V 1

Belt clip LP-84M 1

Instruction Manual 1

Warranty card 1

certicate of quality 1

02

STANDARD ACCESSORIES/OPTIONAL ACCESSORIES

Standard accessories

Optional accessories

Battery

BT FR30 LI

Charger

L CHG 30B

AC adaptor

(12V/500mA)

ADA 12V

Belt clip

LP-84M

USB Programming Cable

WI AL02

Programming software

WPS-301

Earphone

LP-83A、LP-83B、LP-83C

Handheld Microphone

LP-82A

Instruction Manual Warranty card certicate of quality

*1 Note:For the frequency band of Antenna ,please refer to

label indicated in the bottom of the antenna

Antenna *1

VHF(135~175MHz)

UHF(400~480MHz) etc�

03

BATTERY INFORMATION

Charging Operation

WARNING

The battery is not charged at the factory, please charge it before use. Charge the battery for the rst time after purchase or

extended storage (more than 2 months) may not bring the battery to its normal operating capacity. After repeating fully charge/

discharge cycle for two or three times, the operating capacity will reach the best performance. The battery life is over when its

operating time decreases even though it is fully and correctly charged. Replace the battery.

Battery Charger Type

Please use our company's designated charger, other models may cause explosion and injure people. After installing the battery,

if the radio displays low battery, please charge the battery.

Notice for Charging Battery

Do not shortcircuit our company designated charger. Never attempt to remove the casing from the battery, we show no

responsibility on the faulty caused by modifying freely without permission of our factory.

The ambient temperature should be between 5 ℃and 40℃in charging. Charging outside this range may not fully charge the battery.

Always switch off the transceiver equipped with a battery before charging. Otherwise, it will interfere with correct charging.

To avoid interfering the charging procedure, please do not cut off the power or take out the battery during charging.

Do not recharge the battery if it is already fully charged. This may shorten the life of the battery or damage the battery.

Do not charge the battery or transceiver if it is damp. Dry it before charging to avoid danger. Notice for Charging Battery.

When keys or ornamental chains and other electric metails contact with the battery terminals,the battery may cause damage

or hurt bodies.If the battery terminal short circuit.It will generate a lot of heat ,Take care when carrying and using the battery.

Remember to put the battery or radio into insulated container .Do not put into metal container.

04

How to Charge

Plug the AC adaptor into the AC outlet, and then plug the cable of the AC1.

adaptor into the DC jack located on the back of the Charger. The Indicator lights

orange (1s) and then goes out----waits to charge.

Plug the battery or transceiver into the charger. Make sure that the battery2.

terminals are in contact with charging terminals well. The Indicator turns into

twinkling red-----Pre-charging begins.

After pre-charging for about 5 minutes, the indicator will stop twinkling----3.

charging begins.

It takes approximately 4 hours to fully charge the battery. When the lamp lights 4.

green, the charging is nished. Remove the battery or the transceiver equipped

with battery from socket.

BATTERY INFORMATION

Charging Process5.

NOTE: when charging a power-on transceiver equipped with battery.The indicating lamp will not turn into

green to show the fully charged status.Only when the transceiver is switched off.Can the lamp indicate

mornally.The transceiver consumes energy when it is power-on and the charger can not detect the viltage

when the battery has been fully charged.So the charger will charge battery in constant voltage and fail to

indicate correctly whether the battery has been charged fully.

Charging Status Indicator Status

None

Red light twinkles for about

5 minutes

Lights red for about 4 hours

Lights green

Standby (Self-examine lights orange 1second

when power on)

Pre-charging (Pre-charging stage)

Charging (Charge in a constant current)

Fully charged (Charge in a constant voltage)

Ac Input

05

BATTERY INFORMATION

LED indicator:6.

STATUS Self-Examine

When Power on No Battery Pre-charging Charge Normally Fully Charged Trouble

LED Orange (for 1

second) None Red Light Twinkles

for 5 Minutes Red Green Red twinkles

for a long time

NOTE:Trouble means battery heating,batteru-circuit or charger short-circuit.

Normal Charging Tips

1. Self- Examination: When charging, orange light twinkles for 1 second and goes out, which means the charger has

passed its self-examination and it can charge the battery normally. If the light remains orange or the red light twinkles, it means

the charger can not pass its self-examination or charge the battery.

Trickle Pre-Charging:2. If red light twinkles when battery is inserted into the charger, it means the remnant voltage is low

and the charger is trickle-charging the battery (Pre-Charging Status). The charger will automatically turn into normal charging

when the battery reaches a certain electric quantity, And if the red light stops twinkling, it means the remnant voltage meets a

certain electric quantity, the charger will charge the battery normally.

Donot short circuit battery terminals.

Never attempt to remove the casing from the battery pack.

Never assemble the battery in dangerous surrounding spark

may cause explosion.

Do not put the battery in hot environment or throw it into

re,it may cause explosion�

WARNING

NOTE:Trickle charging(Pre-charging status)time can not beyond 30 minutes.If the indicating lamp still twinkles

after 30-minute Trickle-charging ,it mean that the charger can not charge the battery.Please check whether the

battery or charger is damaged.

How to Store the Battery

1. If the battery needs to be stored, keep it in status of 50%

discharged.

2. It should be kept in low temperature and dry environment.

3. Keep it away from hot places and direct sunlight.

06

PREPARATION

Installing / Removing the Li-ion Battery

Match the two grooves of the battery pack with the corresponding1.

guides on the back of the transceiver, and then push it.

Press the battery pack until the release latch on the top of the

2.

transceiver locks. After hearing a “click” sounds, the battery has

been locked.

To remove the battery pack, slide up the release latch and remove

3.

the pack away from the transceiver.

Installing / Removing the Antenna

Installing the Antenna: Screw the antenna into the connector on

the top of the transceiver by holding the antenna at its base and turning

it clockwise until secure.

Removing the Antenna: Turn the antenna anticlockwise to

remove it.

4

07

PREPARATION

Installing / Removing the Belt Clip

Installing the Belt Clip: Place the belt clip to the corresponding grooves

on the back of the transceiver, and then clockwise screw it.

Removing the Belt Clip: Anticlockwise turn the screws to remove the

belt clip.

Installing the Additional Speaker/ Microphone (Option)

Unveil the MIC-SP jack cover and then insert the Speaker/Microphone plug

into MIC-SP jack. If not use Speaker/Microphone,please cover the MIC-SP

jack.

NORE:

1. Do cover the the MIC-SP jack to keep transceiver

waterproof.

2. The transceiver is not completely waterproof while

using the Speaker/Microphone.

08

GETTING ACQUAINTED

LCD Display

On LCD display screen,you will see various icons which stand for the selected functions and sometimes you may forget the

meaning of them.Here you will nd the following table extremely useful.

NOTE:

Battery capacity indicator(full) No power,replace battery pack or charge battery

Real time display receiving signal strength/Power Indicator

Battery capacity remnant

Frequency Reverse

Offset Frequency

The arrow points to

current operational

channel

TX Power

FUNC Icon

Busy channel

CTCSS /DCS

Priority Scan

VOX Function

Narrow Band

Battery Capacity

Scan Skip

Function Menu Serial NO�/

Main Channel NO�Serial NO�

FM channel NO� Serial NO�

Keypad Lock

09

GETTING ACQUAINTED

Front Panel

Antenna

Speaker

Microphone

LCD

Numeric keys

Frequency Switch

Power/Volume Switch

Jacklight

10

GETTING ACQUAINTED

Side Panel

Left Panel

PTT key Speaker/Microphone

Reading/Writing

Programming Software Jack

Belt Clip

Battery

PF1 key:squelch off

PF2 key:high/low power switch

Right Panel

11

BASIC OPERATION

Turn on/off Transciver

Under power-off state ,please turn (POWER)/(VOLUME) clockwise until beeping and current

signal display on LCD,indicate turn on the transceiver.

Under power-on state ,please turn (POWER)/(VOLUME) anticlockwise until beeping "KADA"

indicate turn off the transceiver.

Adjusting Volume

Underpower-on state turn (POWER)/(VOLUME) toadjust volume .Colockwise-up anticolockwise-

down;You could press the programmed as squelch off key to monitor the current volume.

NOTE

You could press [PF1] mintor key to control the background volume.Meanwhile turn (POWER)/(VOLUME) to adjust

volume .The volume will be adjusted more correctly when communicate with other party.

12

BASIC OPERATIONS

Operating mode switch

In standby state,press Key to exchange between frequency mode(VFO) with channel mode.

Channel selection

Under channel mode/FM mode, turn band switch or press key/ key could get the channel you

want:turn band switch clockwise or press key turn to down channel.Anticlockwise or press

key turn to up channel.

If there are empty channels in channels , when adjustment it will skip empty channel to next channel.

Prority Channel

In standby state.press key to set the current channel as priority .It shows "PRI" on LCD.

Prority Channel Setup

In standby state,press1. key to turn walkie talkie to channel mode.

Turn the band switch or press

2. key/ key to choose channel you want.

press

3. key ,it shows on LCD and then press ,it shows "PRI" on LCD.The current

channel is the priority channel .

Wintec LP-301 User manual

Popular Radio manuals by other brands