Winter TRIMMERMAX DELUXE User manual

OPERATION MANUAL
WINTER TRIMMERMAX - DELUXE
WARNING!
The operator must thoroughly read this manual before operation.
Keep this manual for future reference.
Henrik Winter Holztechnik GmbH
Druckereistr. 8
04159 Leipzig
Tel: [phone] Fax: [phone] Funk: +49 (0)171/2820443
Em@il: [email protected] Internet: www.winter-holztechnik.de

1
1.Safety regulations
1.1Warning！
Please read the understanding manual and corresponding security proceduress at the
before using；
After reading have any questions,please don't use equipment,should contact the
nearby distributor.
1.2Safe operation
●please attention on the machine sundries at the start machine;
●At starting machine,please remind worker attention safety at the machine
nearby;
●The machine coated with yellow place,please special attention safe,such as
high temperature object,charged object and tool etc;
●When the working process appear any question,please at once press down
emergency stop switch;
●Please at the cut off power repair machines;
●Strictly unskilled worker open the control box and go with power;
●Before replace electric components,please cut off machine power;
●Regularly check safety protection devices,at once discover fault should
immediately maintenance;
●Starting sequence: connect external power →opening on the control panel
power switch →Ordinal open the motor switch →begining work;
●Power off sequence: at first close the motor switch →cut off on the control
panel power switch→cutting off external power.
1.3Attention:
●The company without agree,please don't change machine structure!
●If you need replace parts,please use the original parts!
●Manual nothing maintenance content,please contact dealer solve!
●The manual use applicable hand movement straight and curve model!
2.Overview
2.1Main part chart specifications:
Processing board thickness
12-60mm
Edge materials thickness
0.4-3mm
Trimming motor power
0.7kw×2
Trimming motor rpm
18000r/min
Net weight
200kg
Overall size
1000×800×1350mm
Functional
Single side double sides and profile trimming

2
3.Main part schematic
(Picture 1）

3
4.Wiring
After confirm the power supply and on the machine control panel cut off power，
the machine power lines attach on the special power to three phase AC380V、
50Hz，and the machine ground lead reliable the land（power lines is four core
wire,yellow and green double color attach ground lead).
5.Adjustment and operation
5.1 Adjust
5.1.1Trimming knife and near wheel concentric adjust
（Picture2）
As show in picture 2,the concentric insert up and down trimming knife hole at
first,get to the up and down trimming knife concentric.Second the concentric insert
up and down trimming knife hold,the need wheel convex insert concentric hold，get

4
to near wheel and up trimming knife of the concentric.the up and down trimming and
near wheel of the concentric at last.
5.1.2 Board thickness adjust
（Picture 3）
As show in picture3,before leave factory setting higher table-board 2mm,to the
bottom copy bearing,the board thickness need not adjust of the change.when the
change board thickness,main adjust up handle,when the thickness numeration table
display board thickness numeration is OK.(when the up handle clockwise
rotation,board is add,opposite is reduce).

5
5.1.3 Trimming feeding adjust
When the up and down board trimming measure is not appropriate,as show in
picture 3 loosen the motor lock handle,turn of up and down feeding measure adjust
handle make the trimming measure get to appropriate.(clockwise rotation feeding
measure adjust handle ,the trimming is reduce,opposite the trimming is add.)
5.2 Operation.
5.2.1Start machine
The power switch turn of“｜”power light is light，at the same times up and
down trimming motor is in the begin，If double trimming press on up trimming
electric switches and down trimming electric switches，the motor begin work.if single
trimming ,just need open the down trimming motor work is ok.（Note:when the motor
in the high speed state，the frequency reach 200HZ above and the other motor is
stop,if open the motor must should the frequency adjust 0HZ in the after two motor
together opening.)
5.2.2 Straight line trimming
（Picture 4）

6
As show in picture 4,the board according to arrow direction depend on front
straight line set pattern,at the straight line trimming before.again turn left move the
board until leaving trimming knife is ok.
5.2.3 Curve line trimming
Reference picture4，at the curve trimming remove the before and behind straight
line set pattern.(If the behind straight set pattern don't block panel move can need not
remove)the depend on wheel according the panel exterior move until trimming finish.
5.2.4 Power off
Strictly direct close the power switch,should one by one close power switch,cut
off without power at last.
6.Electrical part
6.1 Control panel
1、Power switch
2、Power indicator light
3、Down motor switch
4、Up motor switch
5、Speed adjusting table
6、Stop switch HED-S60A Control panel
6.2Electrical diagram

7
7.Maintenance
1.after working finish for each time,the machine need to be cleaned,but not use water.
2.the metal material such as glue part need to use alcohol clean, but not use other
chemical or it will change shape and affect the function of machine.
Every part stick on the glue is forbidden to use hand things to
scratch,avoidscathe the surface and affect the function of machine.
3. Up and down straight line bearings pole and hight adjust pole much regularly the
clean behind add lubrication oil.at the general workload case,each week about 1
times.
8.Troubleshooting
9. Inverter Parameter setting way
At the stop state,long press“MODE”key about 3 seconds,(the numerical tube at the
same times display “ ”),when the numerical tube display“ ”and at the
numerical replace mutual flashing,said explain already enter into common parameters
setting state.press the up key and down key change parameters,press “MODE”key
enter into next ,(at the not need change times,direct press “MODE ”key enter into next
parameters.)when the parameters setting finish,the numerical tube display “”，
prompt whether save this time change,press“MODE”key save exit.
№
Malfunctions
Solutions
1
Electric light not
on,machine do notwork
a.check if the electric wire whether connected.
b.stop whether loose.
c.check if the control wire whether ruin.
2
Motor do not run
a.if the motor have voice,then the electric wire less one phease,connect it；
b.check the motor whether load excessive ,cause plugging turn；
c.other problem,find special worker.
3
At the trimming resistance
excessive shake obviously.
a.check the knife edge whether than more glue? If is glue than
more ,please clean glue；
b.check the knife whether change blunt ,please grinding or changing tools
at the blunt；
c.check motor base ,motor fixed nuts whether loose.

8
9.1Inverter Parameter setting
Symbols
Parameters
4
2.5
0
Fun
3
Fb
3.0
200HZ
6
When the display O = 72 enter extended parameters.
9.2 The need setting expand parameters.
d026
250HZ
d041
5