WIPCOOL P12 User manual

OPERATION MANUAL
feeling for more
P12/P12c
CONDENSATE PUMP
Compact and Flexible,
Silence and Durable

01 02
feeling for morefeeling for more
1. Explosion Diagram
No.
1
2
3
4
No.
5
6
7
8
No.
9
10
11
Part Name
Water inlet pipe
Tank
Filter net
Upper cover
Part Name
Upper cover plate
Air hole(φ6*20)
Water pipe(φ6*1500)
Induction signal line
Part Name
Power cord
Water outlet pipe
Condensate pump
assembly
1.1 P12
1.2 P12C
No.
1
2
3
4
No.
5
6
7
8
No.
9
10
11
Part Name
Outlet port
Upper cover
Pump
Intermediate plate
Part Name
Sealing ring
Tank
Control panel
Power module
Part Name
Four-core power cord
Filter net
Water inlet pipe

03 04
feeling for morefeeling for more
2. Dimension
7
16
7
12
17
85
6
48.3
40
7
7
34
30
14 11.5
154
95
17
17
85.5
7
12
43.5
2.1 P12
2.2 P12C
P12
35ml
0℃~50℃
P12C
12
10
8
7
6
2
0 5 10 15 20 25 30 35 40
P12/P12C
4. Flow Rate Chart
P12
P12C
0m
12
12
2m
10
10
4m
8
8
6m
6
6
7m
4
4
3. Technical Data
Model Performance(l/h@head)
Meters head（m）
Flow（L/h）
Model
Voltage
Discharge Head(max.)
Flow Rate(max.)
Tank Capacity
Mini Splits up to
Sound Level at 1m
Ambient Temp.
12L/h(3.2GPH)
7m(23ft)
30,000btu/hr
19dB(A)
100V-230V~/50-60Hz
45ml

feeling for more
06
5. Safety Instructions
1. Place the tank horizontal when installing, do not tilt the pump. Check whether
the level drop is centered; if there is tilt, adjust the water level before using it.
2. Do not place electrical appliances or valuables under the condensate pump
to avoid loss caused by power failure or water leakage.
3. Non - professional personnel should not install it to avoid danger.
4. The condensate pump is not waterproof. Do not place it in the open air,
outdoors or in a place prone to flooding.
5. The condensate pump power supply needs to be independent to maintain
permanent power supply. For details of connecting with air conditioning
system, please refer to the wiring diagram.
6. It is prohibited that the water inflow is bigger than our stated flow rate, which
will easily cause the motor to work continuously and fail. Instant big water
inflow will also cause the condensate pump fail to discharge water in time,
leading to water leakage.
feeling for more
6. Installation Procedure
(1) Make sure the probe in the tank is on the right side of the filter net, the filter net and
the upper cover are firmly mounted on the tank. (as shown below)
(2) Make sure the tank is placed smoothly and the outlet pipe of the air conditioner is
tightly connected with the water pipe of tank. (as shown below)
(3) P12 Connect the vent pipe with the air hole. P12C don't need to connect
(4) Place the pump in the position beyond the ceiling. (as shown below)
05
P12 P12C
2
3
1A
B
45

feeling for more
08
feeling for more
07
(6) Pay attention to the direction of the water flow. (as shown below)
(7) Connect the water tank and pump with 6x9 silicone tube and fasten it with tie,
make sure the length of the water pipe is less than 1.5m ( as shown below )
1.5M
(8) Connect the 6x9 water pipe to the water outlet, tie the water pipe, make sure that
the discharge head is less than 6m and the length of the water pipe is less than
15m. ( as shown below )
15M
6M
Insert in alignment
with arrow direction
Locking
Alignment of locating slots
(9) P12C Drainage Pump has built-in alarm buzzer. When the pump fails and water
level reaches the alarm level, the buzzer will sound "om ... om".
(10) Connect the power cord, insert it in the direction of arrow on the power cord, and
then lock the nut. (P12C)
(5) The use of shockproof materials, ensure the water tank and condensate pump
stuck firmly, low vibration to avoid noise.

09
feeling for more
Please pay attention to distinguish the power cord from the signal line,
incorrect wiring will cause damage to the condensate pump. Ensure the
voltage is consistent with pump.
(12) Pour some water into the evaporator tray to check whether the tray leaks and the
condensate pump works normally.
WARNING
1A
B
C
Pump runs
all the time
1. Installation is not horizontal
2. There is sludge inside tank
Problem Cause Action
Pump makes
loud noise
Pump can’t
start working
Adjust the tank make it level
Clean the inside of tank and probe surface
1. The water is siphoning back
in the pump
Check whether the outlet pipe is lower than
pump thus result in siphoning, raise the
condensate pump position
1. Installation is not horizontal
2. The power can’t reach pump
3. The voltage isn’t correct
Adjust the tank, check water level
Check power supply
Check the voltage
7. Troubleshooting
Note: Proper use and maintenance can improve the life of pump. We suggest to check
and clean the condensate pump before seasons changing or next year using.
feeling for more
(11) Power supply wiring, in order to avoid leakage of condensate pump, please
connect the alarm signal line and the "Normally Closed" signal terminals according
to the requirements of different working conditions
(as shown below).
L
N
E
If the air conditioner does not have liquid level
control terminal, it can be connected to other
alarm devices or refer to figure 2.
If there is no liquid level switch, it can also use an
appropriate AC contactor to control the air
conditioning power.
Power cord: (L) fire wire: Brown (N) zero line: Blue
Signal line: (NC) normally closed: Black (COM) common line: Black
Air Conditioner
Indoor Unit
Liquid Level Switch
Condensate
Pump
L N E
L N E L N E
COM Black
N.C Black
Air Conditioner
Outdoor Unit
L
N
E
Condensate
Pump
Air Conditioner
Indoor Unit
Air Conditioner
Outdoor Unit
L N E
L N E
N E
AC Contactor
10
COM Black
N.C Black