Wirepath WP-MOD-RJ45-TEL1X12 User manual

TROUBLESHOOTING
Wirepath™structured wire modules are designed to function trouble-free. Most problems
that occur are due to simple issues. If you have trouble, please check the list of simple xes
below. If the problem persists, contact your authorized Wirepath™dealer or Wirepath™
customer service at 866.838.5052.
No Telephone signal
• Verify that there is signal on the input being used.
• Check all wiring connections on output(s) with no signal, including any wall-plate
connections at the remote location.
• Disconnect RJ-31X cable if this option is being used. Retry operation.
• Check jumper wire from WP-MOD-RJ45-TEL1X12 if the only trouble is with locations
connected to the WP-MOD-TELEP16.
INSTALLATION GUIDE
TELEPHONE MODULES
>> WP-MOD-RJ45-TEL1X12
>> WP-MOD-RJ45-TELEP16
INTRODUCTION & FEATURES
INSTALLATION
SPECIFICATIONS
2
2/3
4
Lifetime Warranty
All Wirepath™products have a Lifetime Limited Warranty. This
warranty includes parts and labor repairs on all components
found to be defective in material or workmanship under normal
conditions of use. This warranty shall not apply to products which
have been abused, modied or disassembled. Products to be
repaired under this warranty must be returned to SnapAV or a
designated service center with prior notication and an assigned
return authorization number (RA).
For Technical Support: 866.838.5052
®

Thank you for purchasing a great item from one of the highest value lines in structured wiring
available today, Wirepath™. We appreciate your purchase and are committed to being the
best choice for your needs.
The Wirepath™ WP-MOD-RJ45-TEL1X12 and WP-MOD-TELEP16 are superb choices
for almost every type of home installation. They have been designed with advanced
technology components that allow high performance while being exible enough for
any type of installation. Use other Wirepath™structured wire items for your installation
needs to get the best value possible in any system.
IMPORTANT INSTRUCTIONS
• Read and understand all instructions.
• Do not use this product near water, such as a bath tub, wash bowl, sink, pool or in a wet basement.
• Never install wiring for telephones during a lightning storm.
• Never touch bare telephone wires or connections unless the main line has been disconnected at
the interface.
• Use caution when installing, terminating or modifying any type of wire.
WIREPATH™TELEPHONE MODULE FEATURES
TELEPHONE DISTRIBUTION FOR UP TO 4 LINES AND 12 LOCATIONS
Maximize your exibility choose either a 110 punchdown for incoming line or use the RJ45 expansion
port. If you need to add more locations, jumper out of any of the RJ45 outputs and connect to
WP-MOD-RJ45-TELEP16.
TELEPHONE EXPANSION FOR UP TO FOUR LINES TO 16 LOCATIONS
The WP-MOD-RJ45-TELEP16 can easily be added to the WP-MOD-RJ45-TEL1X12 with
a simple jumper cable for an additional 16 locations, with the added benet of another RJ45 output
to add more locations using an additional WP-MOD-RJ45-TELEP16 module.
RJ-31x JACK FOR EASY INTEGRATION WITH SECURITY SYSTEMS
Using the industry standard of interrupting the center pins and routing them through a security panel
requires no unnecessary cutting or splicing.
INSTALLATION
PLACING YOUR WIREPATH STRUCTURED WIRE MODULE
Wirepath™ structured wiring modules are designed to t Wirepath™ enclosures, but also t most major
brands as well. Installation is simple with our familiar expansion pins. Plan the placement of each model
in the enclosure based on how the wire is entering the enclosure, and what will allow for the cleanest
routing of wires.
If the Wirepath™module is being used in an enclosure of another brand, it may be necessary to use one
of the included spare mounting pins in the extra mounting ange hole and remove the two pins on that
side to t the mounting pattern of other enclosures from another brand.
TELEPHONE WIRING
A standard 110 punch down tool is all that is required to properly connect the wiring to the module.
See illustration.
NOTE: The RJ45 Expansion outlet
can also be used for incoming signals
if installation requires it. Use any
RJ45 Output to jumper to expansion
modules. Wire umper to 568B
requirements (see below).
RJ-31X WIRING (WP-MOD-RJ45-TELEP16 only)
If it is necessary to interface the telephone wiring with a security system, simply use the provided jack.
Follow the illustration below if you need to make a cable for this use.
EXPANSION PORT
If it is necessary to expand beyond 12 locations, connect the WP-MOD-RJ45-TEL1X12 with an 8
conductor jumper wired 568B specication. Multiple modules can be daisy chained. The limit will
vary based upon the installation.
Proper Connection
Do not untwist pairs
more than 1/2”
The connector is an insulation
displacement system. Use a
high quality 110 punch down
tool to push the wire into the
contacts. Use of other tools such
as screwdrivers or pliers will
result in poor performance and
may damage the connectors.
Ring Return - 1
Ring - 4
Tip - 5
Tip Return - 8
1
4
5
8
RJ-31X
Pin
1- White/Orange
2- Orange
3- White/Green
4- Blue
5- White/Blue
6- Green
7- White/Brown
8- Brown
White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown