Wirie AP Quick start guide

Upgrade Instructions
How to upgrade The Wirie to The WirieAP

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 2
Contents
Introduction................................................................................3
What’s Included ........................................................................................................................................ 4
Hardware Upgrade .....................................................................5
Step 1 –Prepare for Upgrade ................................................................................................................... 5
Step 2 –Locate Required Parts ................................................................................................................. 5
Step 3 –Remove the WiFi Adapter........................................................................................................... 6
Step 4 –Remove Coax Cable and USB Cable ............................................................................................ 7
Step 5 –Install Antenna Adapter .............................................................................................................. 8
Step 6 –Install WirieAP Access Point ......................................................................................................... 9
Step 7–Install Wirie WiFi Adapter ..........................................................................................................10
Step 8 –Connect USB Cable to WiFi Adapter .........................................................................................11
Step 9 –Insert the DC Electrical Cable.................................................................................................... 12
Step 10 –Connect the DC Cables............................................................................................................13
Step 11 –Position the DC Cable.............................................................................................................. 14
Step 12 –Close the Enclosure.................................................................................................................15
Step 13 –You Now Have The WirieAP! Irie, Mon! .................................................................................. 15

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 3
Introduction
Congratulations on your purchase of The WirieAP Upgrade Kit!
We truly believe that The WirieAP is the best equipment you can install on your boat or RV to increase
your ability to connect to wireless networks and share that internet connection wirelessly in your own
environment. However, please keep in mind that you are also dependent on the access points to which
you are attempting to connect. Not every harbor, anchorage, campground or RV Park will have a
wireless network that you are able to connect to, even with The Wirie. Depending on the access point
equipment, and obstacles between The Wirie and the access point, your range and ability to connect will
vary greatly. Hotels, marinas, and RV parks with high-end wireless equipment will allow connections
from miles away with The Wirie, but smaller, in-home equipment, may not be useable unless your
proximity is fairly close.
Below is all the information you need to install The WirieAP Upgrade Kit.
The WirieAP Upgrade Kit will allow you to upgrade your existing Wirie to all the functionality included in
The WirieAP. This manual will walk you step by step through the installation. Once installed, please refer
to The WirieAP User Manual for information on how to operate The WirieAP (see
www.thewirie.com/wiriedrivers.html for the User Manual).
If you have any questions, please contact us via our support page at www.thewirie.com/support.html.

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 4
What’s Included
The following items should be included in your Upgrade Kit:
The WirieAP Access Point (white box with antenna and power cable assembly)
Short USB Cable
Antenna to WiFi Adapter Connector (small metal connector)
40’ of DC Electrical Cable
Short Ethernet Cable (Bagged with AC Adapter)
Short 110/220 AC Adapter (Bagged with Ethernet cable)
Please Note: You will need an 8mm wrench/spanner (not included) and enough surface area to lay The
Wirie flat to complete the installation.

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 5
Hardware Upgrade
Before you begin:
Open The Wirie AP Upgrade Kit and be sure that your kit includes the six upgrade parts that are listed
above. Use the chart to identify the parts.
Read through the procedure before you begin the step-by-step upgrade.
Step 1 –Prepare for Upgrade
Gather all the needed items to perform your upgrade:
Your existing Wirie and all existing USB cabling
Your WirieAP Upgrade Kit
8mm Wrench/Spanner
Step 2 –Locate Required Parts
The following parts are included in the Upgrade Kit but are not necessary for this upgrade. They will be
used at a future date in case the currently installed software (firmware) on The WirieAP needs to be
updated. They were shipped to you packaged together in a bag. Please put the following items in a safe
place for future use:
Short Ethernet Cable
Short 110/220 AC Adapter
Parts needed for the upgrade:
The Wirie
The WirieAP Access Point (white box with antenna and power cable assembly)
Short USB Cable
Antenna to WiFi Adapter Connector (small metal connector)
40’ of DC Electrical Cable

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 6
Step 3 –Remove the WiFi Adapter
1) Open The Wirie waterproof enclosure.
2) Pull the WiFi adapter off The Wirie enclosure door.
3) Unscrew the coax cable from the top of the adapter using your fingers.
4) Pull out the USB plug from the bottom of the adapter.

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 7
Step 4 –Remove Coax Cable and USB Cable
1) Unscrew the coax cable from the antenna at the top of the enclosure.
2) Loosen the water-tight gland at the bottom of the enclosure and remove the USB cable.
3) Leave the water-tight gland loose for step 9 of the upgrade procedure.
Note: These 2 cables you just removed are not needed for The WirieAP.

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 8
Step 5 –Install Antenna Adapter
1) Screw on the Antenna to WiFi Adapter Connector onto the base of the antenna. Hand-tighten
only.

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 9
Step 6 –Install WirieAP Access Point
1) Insert the short USB cable to the top of The Wirie AP Access Point. This cable only inserts one
way so be sure to attach the plug with the cable going to the right, as shown below.
2) Press The WirieAP Access Point onto the Velcro where the WiFi adapter was attached previously.
Note:Be sure it is mounted so that the positioning of the small rubber antenna allows the door to
close freely. The USB cable should be at the top, and the power cable at the bottom.

©2011 Island Consulting, Inc. All Rights Reserved. (Rev 1.4) 10
Step 7–Install Wirie WiFi Adapter
1) Using an 8mm wrench/spanner, screw the WiFi adapter that you previously removed to the
Antenna to WiFi Adapter Connector. Tighten so that the WiFi Adapter is held securely in place
and is now suspended by the antenna inside the waterproof box. The WiFi adapter should not
rotate or move once securely attached. Be sure the adapter is facing outward as shown in the
picture below. Do not over tighten as you may damage the WiFi adapter.