Wisco Industries DP70 User manual

WISCO DP70 Manual V2.0 Page I
Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900
Tel [phone], Fax [phone], www.wisco.co.th, E-mail [email protected]
Universal Input Indicator
DP70
Optional Analog Output

Page II WISCO DP70 Manual V2.0
-
[phone], [phone]-1, [phone], www.wisco.co.th,  [email protected]

WISCO DP70 Manual V2.0 Page III
Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900
Tel [phone], Fax [phone], www.wisco.co.th, E-mail [email protected]
สารบัญ
Universal Input Indicator ............................................................... 1
I. Example of application ................................................................... 2
II. Wiring diagram .............................................................................. 2
III. setting ............................................................................................ 3
1. Menu Input Type ............................................................................ 5
2. Menu Scale ..................................................................................... 7
3. Menu Analog Output ....................................................................... 8
4. Menu Alarm ................................................................................... 10
5. Menu Calibrate .............................................................................. 12

Page IV WISCO DP70 Manual V2.0
-
[phone], [phone]-1, [phone], www.wisco.co.th,  [email protected]

WISCO DP70 Manual V2.0 Page 1 of 13
Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900
Tel [phone], Fax [phone], www.wisco.co.th, E-mail [email protected]
Universal Input Indicator
DP70
-5 Digits Display
-Programmable Input type
-2 Alarm Relay
-1 Analog output or RS485
(Option)
Universal Input Indicator is panel meter with programmable input. It has
5 digit and 2 set of alarm (Hi/Low). Moreover there is optional for analog output
Specifications
Serial Interface (Optional)
Serial Standards: RS485 (Isolated)
2 Pin Terminal Block
Loading: RS485 Max 32 Unit
Distance: RS485 Length 1 Km.
Protocol: MODBUS ASCII/RTU
Supply Software: Citect, Wonderware, LAB
View etc.
Monitor
Display: 5 digits, 14.2 mm. (7-Segment)
Display Color: Red (std)
Analog Input
Number of channel: 1 Channel
Input type: Programmable
Input range:
Thermocouple (R, S, K, E, J, T, B)
RTD (Cu10, PT100, PT1000)
Resistance (0 to 600 Ω, 0 to 1200 Ω,
0 to 4000 Ω)
Voltage mVDC (0 to 80, 0 to 150 mVDC)
Voltage (0 to 1, 0 to 5, 0 to 10, 0 to 30 VDC)
Current (4 to 20, 0 to 20, 0 to 40 mA)
ADC Resolution: 16 bits
Accuracy: ± 1 least significant digit
Analog Output (Optional)
Number of channel: 1 Channel
Output type: Current, Voltage
Output range:
Current (0 to 20, 4 to 20 mA)
Voltage (0 to 1, 0 to 5, 0 to 10 VDC)
Output Impedance:
Current Max Load 800 Ω
Voltage Min Load 1000 Ω
Relay Output
Number of Channel: 2 Channels (Alarm)
Relay Type: N.O. or N.C.
Contact Rating: 6A@250VAC, 6A@30VDC
Power Requirements
Power Supply: 85 to 230 VAC
(12 to 35 VDC Optional)
Environmental Limits
Operating Temperature: 0 to 55 °C
Operating Humidity: 5 to 95% RH
Storage Temperature: 0 to 70 °C
Physical Characteristics
Dimension: W96 x H48 x D120 mm.
Panel Cutout: W90 x H40 mm.
Mounting: Panel Flush Mounting
Wiring: Screw terminals
Warranty
Warranty Period: 5 Year

Page 2 of 13 WISCO DP70 Manual V2.0
-
[phone], [phone]-1, [phone], www.wisco.co.th, [email protected]
I. Example of application
Pressure
Transmitter
Input Alarm Output
Analog Output
Data Logger
II. Wiring diagram
15
A/D
24 Bit
SUPPLY
220 VAC
MCU
Display
AL1
AMP
RS485
L(+)
N(-)
16
17
VI
13
12
14+24X
+
-
2 Wire Transmitter
Jump for mA
1
2
3
4
8
6
7
5
11
10
AL2
9
+
-
Current
Voltage
+
-
+
15
16
17
V
POT
RTD
A
B
B
TC mV/Volt
15
16
17
15
16
17
15
16
17
mA

WISCO DP70 Manual V2.0 Page 3 of 13
Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900
Tel [phone], Fax [phone], www.wisco.co.th, E-mail [email protected]
III. Setting Menu
Mode 3 
Input Type TC
RTD
R(Ohm)
mV
V
mA
R,S,K,E,J,T,B
Cu10,Pt100,Pt1,000
600,1200,4000
0-80,0-150
0-1,0-5,0-10,0-30
4-20,0-20,0-40
Mode
Exit
ExitMode
Exit
ExitMode
ExitMode
Exit
Exit
Mode Exit
Exit
Mode Exit
Exit
Mode Exit
1 2
Mode
Scale 0,1,2,3,4,
Max Rang
Min Rang
Mode Exit
High Value
Mode Exit
Low Value
Exit
Exit
Exit
Mode
Mode
Display

Page 4 of 13 WISCO DP70 Manual V2.0
-
[phone], [phone]-1, [phone], www.wisco.co.th, [email protected]
Alarm 1 High, Low
Parameter
Parameter
Analog Output
Min Rang
Max Rang
1 2
High Value
Low Value
Mode Exit
Exit
Exit
Mode
Mode
Level
Mode Exit
Exit
Set point
Mode Exit
Exit
Hysteresis
Mode
Exit
Mode
Alarm 2 Level High, Low Exit
Mode Exit
Parameter
Parameter
Set point
Hysteresis
Exit
Mode Exit
Mode
Exit
Mode
Exit the menu by hold Exit button for 3 second

WISCO DP70 Manual V2.0 Page 5 of 13
Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900
Tel [phone], Fax [phone], www.wisco.co.th, E-mail [email protected]
Setting Menu for DP70
1. Menu Input Type
Input Type
Mode Mode Mode Mode
Thermocouple RTD R (Ohm) Voltage Current
Mode
mV
Menu Input Type is for setting type of input. DP70 has 6 type of input which
isThermocouple, RTD, R (Ohm), mV, Voltage andCurrent as detail below
Thermocouple Input
Thermocouple
Type R Type S Type K Type E Type J Type T Type B
Set upThermocouple Input push Mode button for3 secondthen choose
usingto choose for thermocouplethen using to
select thermocouple type R, S, K, E, J, T, and B. click on Exit button to go the
next step.
RTD Input
RTD
CU 10 PT 100 PT 1000
Set upRTD Input push Mode for 3 second then choose  clickMode
then select then using button to select type of RTD which is Cu10,
PT100, PT1000 then click Exit button to go to the next step.
R (Ohm) Input
R (Ohm)
600 Ω1200 Ω4000 Ω
Setting R (Ohm) Input by clickMode button and hold for 3 second then
setting menu will appear  click on mode button to select  for
input then click to select type of desire input which areType 600 Ω, 1200
Ω, 4000 Ω then click on Exit button to go to the next step.

Page 6 of 13 WISCO DP70 Manual V2.0
-
[phone], [phone]-1, [phone], www.wisco.co.th, [email protected]
mV Input
mV
0-80 mV 0-150 mV
SettingmV Input by click Mode button and hold for3 second to go setting
menuthen select to choose input type. Click onMode button to select
for mV input. Use  button to choose mV type which is 0-80 mV,
0-150 mV then click on Exit button to go to the next step.
Voltage Input
Voltage
0-1 VDC 0-5 VDC 0-10 VDC 0-30 VDC
Set upVoltage Input clickMode button and hold for 3 second to go to
setting menu then select to choose input type. Click on mode button
to select for Voltage input. Use  button to choose Voltage input
type which is 0-1, 0-5, 0-10, 0-30 VDC then click on Exit button to go to the
next step
Current Input
Current
4-20 mA 0-20 mA 0-40 mA
Set upCurrent Input click Mode button and hold for 3 second to getting in
to setting menu then select to choose input type. Click on mode
button to select  for Current input. Use to select type of Current
input which is 4-20, 0-20, 0-40 mA then click on Exit button to go to the next
step.