Wisenet QRN-810S Installation guide

NETWORK VIDEO RECORDER
Quick Manual
QRN-410S/810S/1610S

2
QRN-1610S
DV25
SRN-475S
NETWORK VIDEO RECORDER
REC HDD ALARM NETWORK BACKUP POWER
NVR Mouse Power Cable
User Manual CD User Manual or Quick Manual Terminal block
Remote Control /
Remote Control Battery (AAA) Bracket rack Bracket Fixing Screw
HDD Installation
QRN-410S/810S
M
`The following figures are based on Model QRN-810S.
1 After unscrewing, push back and remove the cover. 2 Connect the SATA/power cables of the HDD to the
connectors on the mainboard.
USB
REC LAN POWER
UHD
USB
REC LAN POWER
UHD
3 Using the screws, fix the HDD to the bottom of the
set.
4 Check for any problems in the connection terminal
and the wiring in the product, close the cover and fix
it with screws.
`Be careful not to damage the cables when you close the
cover.
USB
REC LAN POWER
UHD
PoE CAMERA
VIEWER
USB
DC 54V
HDMI
Package Contents
M
`Accessory category and quantity may differ depending on sales region.
QRN-410S
USB
REC LAN POWER
UHD
NVR Mouse Power Cable
Power Adaptor User Manual CD User Manual or Quick Manual
HDD Fixing Screw SATA Cable
QRN-810S
USB
REC LAN POWER
UHD
NVR Mouse Power Cable
Power Adaptor User Manual CD User Manual or Quick Manual
Remote Control /
Remote Control Battery (AAA) HDD Fixing Screw SATA Cable

3
5 Close the cover, and tighten a setscrew in the back.
USB
REC LAN POWER
UHD
QRN-1610S
1 After unscrewing, push back and remove the cover. 2 Separate them by unscrewing the fixed bracket
screw and push it towards the arrow on the board.
AC 100
240~IN
VGAOUT
AUDIO
OUT
HDMI
VIEWER
USB
1 2 3
1 2
4
NCNO NO
COM COM
ALARM IN
G
GG
ALARM
OUT
1 3 5 7
2 4 6 8
9 11 13 15
10 12 14 16
PoE CAMERA
3 After aligning and inserting one side of the HDD to
the bracket, open the other side bracket wide and
insert the HDD between them.
`Align a hole in the bracket with a screw hole in the HDD to fix
them.
4 Push the bracket with the HDD installed and tighten
the screws to fix it.
AC 100
240~IN
VGAOUT
AUDIO
OUT
HDMI
VIEWER
USB
1 2 3
1 2
4
NCNO NO
COM COM
ALARM IN
G
GG
ALARM
OUT
1 3 5 7
2 4 6 8
9 11 13 15
10 12 14 16
PoE CAMERA
5 Close the cover and tighten the screws to fix it.
Install Wizard
1 Select the language
Select your preferred language.
2 Set Password
Set a password.
※Click icon to see the password rule
8 ~ 9 characters : All combination of English character, Digit, Special character
10 ~ 15 characters : Two combination of English character, Digit, Special character
※Not allowed to use same characters with ID
※Not allowed to use 4 or more continuative or repeated characters
2-1. Setting Camera Password
You can change the password of the camera one step.
If the password of the camera is the default password set in the factory, enter a new password to change it. The
password will be changed, and the new password will be registered.
If the password of the camera is not the default password set in the factory, enter the current camera password.
The current camera password will be registered.
- New Password : Input a new password according to the password setting rules.
- Confirm Password : Input the new password again.
`A camera password registered with ONVIF and RTSP cannot be changed.
3 Set up Network
•DHCP server : If the DHCP server is set to enable, an IP is automatically assigned to the camera.
•Network 1 (Camera) : Connects to the camera and receives the video feed from the camera.
•Network 2 (All) : N etwork for a remote viewer (SSM, Smart Viewer, Webviewer)
•Network 1 / Network 2 Setup
- IP Type : Choose the network connection method.
- IP Address, Subnet Mask, Gateway, DNS
•Switch Mode : PnP Mode and Manual Setup Mode
If PnP Mode is selected, NVR will assign IP address to the IP cameras automatically.
If Manual Setup Mode is selected, you need to search and add the IP cameras to the NVR.
※For more details on network settings, refer to the User manual.
► To use a simple intranet, click <Next>.

4
Additional camera registration
In the <Install Wizard> setting, make a connection to the camera automatically registered and use the menu
path to register and connect a camera.
Menu ;Device ;Camera ;Cam Registration ;Auto
a
b c e
d
To register a camera, follow these steps:
aSelect the camera to register (you can select multiple cameras).
bClick <ID/PW> to register your ID and password. (If you do not register a new ID/PW, then the default
ID/PW combination is used.)
cClick <Connection Test>.
dCheck the connection results.
eIf the channel connected successfully, click <OK> to end the camera registration process.
M
`Click an item on the table to see a preview (you must change the ID/PW in step bif the camera account changes).
`Click the table headers to sort the content.
`Click < > to check if a new IP address was allocated to the camera when you rescan the network or when an IP
address was not assigned by the DHCP server (e.g., 192.168.1.100). If the IP still stays the same, then select Assign IP to
assign the IP manually.
4 Set Date & Time
Set the time and date and click the <Finish> button, and the installation will be completed.
5Camera Registration
When the installation wizard finishes, the camera is automatically registered.
5-1. If there are 16 or less cameras searched, it will be automatically registered and the camera information(fps, days
of recording) will be displayed.
► Select <OK> and the frame rate of all cameras registered is set to 30fps and the installation session is
completed.
► When you select <Manual Setting>, the frame rate of all cameras registered can be set to a value selected
by the user (move to 5-2).
5-2. Adjust the recording framerate
Changes the recording frame rate for all cameras at once.
Please note that the estimated recording days vary depending on the frame rate.
< Figure 5-1 > < Figure 5-2 >
5-3. If there are more than 16 cameras searched, Camera registration window will be displayed.
Select a camera to register and click the <Register> button. Once camera registration is finished, proceed in 5-1.
< Figure 5-3 >
After selecting a camera, press the register button.
Searched Cameras
Refresh
Status
|
Model
|
IP
|
MAC
|
Network
|
Connected Authentication errors Disconnected
Exit
Register
0/16
Camera Register

5
Configuring the Recording
This section outlines how to configure and view the recording settings for each channel.
a
b
c
F F F F
F F F F
F F F F
F F F F
FULL NO
Recording Restriction
Record data size exceeded limitation
Only key frames are recorded
Please check the record settings
Do not show this message again
OK Record Status
d
aShows the standard and event recording method for each channel.
•FULL : Records all the frames received from the camera.
•KEY : Records only the key frames received from the camera. In general, one or two frames per second
are recorded, but you can adjust this in the camera settings.
•OFF : Turns off recording.
bShows the transmission size of the recording data for each channel.
cShows the data size limit for each channel.
M
`The orange colored channel indicates the case where the b input data load is greater than the c permitted data load.
If you set the c permitted data load to greater than the b input data loads, it will be changed to orange.
`If the sum of input data for each channel is greater than the max level for the camera, then d the recording exceeding icon
and the alarm message will be displayed. In this case, for the channel exceeding the input limit will record the main
frame(one or two per second) only.
Setting Up the Camera
From the setup menu, you can configure the camera settings (resolution, frame rate, and quality) and other
functional settings.
Menu ;Device ;Camera ;Camera setup
Camera function settings: You can configure the camera
settings or the live movie format to change the settings in the
camera itself.
•Add : Adds a camera profile.
•Delete : Deletes the selected profile from the list.
•Profile : Specifies the movie profile of the connected camera in the camera settings.
•Codec : You cannot change the codec of the selected profile.
•Resolution : Specifies the resolution of the selected profile.
•Frame Rate : Specifies the frame rate of the selected profile.
•Bitrate Control : Specifies the bitrate of the video transmitted for the selected profile.
Setting Up a Channel
From the channel setup menu, you can change the camera name shown in live mode.
Menu ;Device ;Camera ;Channel setup

6
Use the basic guide
Show shortcut menu
Right-click on the live screen and you can access various functions that NVR provides. Hover over an icon and a brief
definition of term for each function is prompted.
Live launcher
aYou can configure a live layout.
bYou can configure a supported split mode. You can view the end sequence ( ) in serial order for a specific
period of time for each split mode.
cYou can configure additional functions in the live screen, such as alarm control or audio.
Layout
In the live screen, you can set the layout for each channel.
This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a
single layout.
Example) Layout “Lobby” - Lobby camera 1, Lobby camera 2, Front entrance camera 2
Layout “VIP” - Directors’ meeting room 1, Directors’ meeting room 2, Directors’ lounge 1, Corridor camera on the 7th
floor
To create a new layout, follow these steps:
aOpen the channel layout setup menu.
bClick <New>.
cEnter a name for the selected channels (e.g., PARKING).
dSelect the channels that you want to add to the layout (e.g., 1, 2, 3, 4).
eChoose a split mode to apply (e.g., 4-way split).
fClick <OK>.
gChoose a layout to view it on the screen (e.g., change to PARKING).
ab c
def
c
b
g
a
Full Screen
Layout 
Keep ch. scr ratio
Status 
PTZ Control
ZOOM
Audio 
Freeze
Stop Alarm
Capture
Record
Play
Search
Backup
Menu
Quick Setup 
Shutdown
Logout
Hide Launcher

7
http://hanwha-security.com
http://hanwha-security.com
QRN-1610S
QRN-1610S
QRN-1610S
QRN-1610S
QRN-1610S
QRN-1610S
QRN-1610S
QRN-1...
QRN-1...
QRN-1610S
Using P2P Service
When using P2P service, NVR can be used by connecting to mobile web viewer.
aWhen <Enable P2P> is checked, the connection test runs to check if it can be remotely connected from the
current NVR.
bWhen the connection is successful, search for WiseNet Mobile from the smart phone, and then install and run it.
`When Add a device > QR code is selected, the NVR QR code can be scanned.
c
When the QR code is scanned, the device ID that can be seen in NVR is automatically converted to mobile
viewer ID, and the mobile viewer can be used right away when the ID/password of NVR is entered.
dAfter this, it automatically connects to NVR and can be monitored easily with a smart phone when running
WiseNet mobile app saved in the smart phone.
M
`The expiration date for the P2P service is three years after the purchase of the product, and the remaining period can be checked in
mobile FAQ.
qrn1610s
QRN-1610S - CAM 05
Use product information
You can check product information/user manual/firmware information/FAQ/HDD compatibility list, etc. on the website
or mobile app on your smartphone.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide
customers with more environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates
that the product satisfies the EU RoHS Directive.

Head Oce
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : [phone] Fax : [phone]
http://hanwha-security.com
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free : +1.877.213.1222 Direct : +1.201.325.6920
Fax : [phone]
www.hanwha-security.com
Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel : [phone] Fax : [phone]
www.hanwha-security.eu
Hanwha Techwin(Tianjin) Co.Ltd
No.11, Weiliu Rd., Micro-Electronic Industrial Park, Jingang Road Tianjin 300385, China
Tel : [phone]
www.hanwha-security.cn
Hanwha Techwin Middle East FZE
JAFZA View 18, 20th oor, oce 2001, 2002, 2003, Downtown Jebel Ali,
Dubai, United Arab Emirates
http://hanwha-security.com