Wisenet SPD-1660R Installation guide

NETWORK VIDEO DECODER
RACK
Quick Manual
SPD-1660R

2
Features
This product can monitor the video and audio from network cameras.
Provides an environment in which you can set this product on your PC.
• User-friendly UI
• Supports various 4K camera resolutions 3840x2160@60HZ/30HZ (Only HDMI-HDMI 1)
• Supports up to 16 monitors (2 outputs per decoder (4K, 1080P) and a separate VGA (Clone))
• HDMI input (PC input / 1 port only)
• Supports ONVIF Profile S standard and RTP / RTSP protocols
• Can register up to 128 channels
• Alarm Input / Output
• Supports merging between monitors
• Supports various user-defined layouts
Package Contents
Please unwrap the product, and place the product on a flat place or in the place to be installed.
Please check the following contents are included in addition to the main unit.
G
RS485
G
1 2 3 4 5 6 7 8 910
111213 14 15 16
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COMCOM COM
NC
G G
NETWORK
NETWORK RUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
Decoder Power Cable User Manual CD
User Manual or Quick Manual Terminal block
How to install the SPD-260B in the SPD-1660R
J
`Turn off the SPD-1660R and install the blade (SPD-260B).
1 Unscrew both sides of the cover on the SPD-1660R blade (SPD-
260B) mounting slot.
G
RS485
G
1 2 3 4 5 6 7 8 910
111213 14 15 16
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COMCOM COM
NC
G
G
NETWORK
NETWORK RUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
2 Insert the blade (SPD-260B) into the slide grooves on both sides as
shown in the figure, and push it in the direction of the arrow.
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
G
RS485
G
1 2 3 4 5 6 7 8 910
111213 14 15 16
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COMCOM COM
NC
G
G
NETWORK
NETWORK RUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
3 Slide the blade (SPD-260B) into the rack until the ends of the rack
are aligned and tighten the screws.
※This is applied when all the blades (SPD-260B) are installed.
※Mount the blade (SPD-260B) in order from left (Figure 1).
G
RS485
G
1 2 3 4 5 6 7 8 9 10
1112 13 14 15 16
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COMCOM COM
NC
G G
NETWORK
NETWORK RUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
a b c d e f g h
Connecting to an external device
※Unrated or improper power source may cause damage to the system. Ensure that you use only the rated
power source before pressing the POWER button.
※HDMI does not support audio output.
G
RS485
G
1 2 3 4 5 6 7 8 9 10
1112 13 14 15 16
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COM COM COM
NC
G G
NATWORK
NETWORK RUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
AUDIO
HDMI IN
HDMI 2 HDMI 1
VGA 2 VGA 1
VIDEO OUT
(VGA/HDMI)
AUDIO OUT HDMI input from PC

3
Manual Network Setup
Run <IP Installer_v2.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
1 Select desired network decoders from the search list.
Check the MAC (Ethernet Address) on the back of the
network decoder.
Both the [Auto Set] and [Manual Set] buttons will be
activated.
2 Click [Manual Set].
The Manual Setting dialog appears.
The <IP Address>, <Subnet Mask>, <Gateway>,
<HTTP Port>, and <Port (TCP)> of the network
decoder are displayed as the previously set values.
3 In the <Address> pane, provide the necessary
information.
• MAC (Ethernet) Address : The MAC address
imprinted on the camera label is automatically
displayed and requires no user setting.
J
`IP related parameters can be set only when DHCP is not
checked.
Auto Network Setup
Run the <IP Installer v2 XX.exe> program to display the network decoder search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
1 Select your desired network decoders from the search
list. Check the MAC (Ethernet Address) on the back of
the network decoder.
Both the [Auto Set] and [Manual Set] buttons will be
activated.
2 Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>, and
<Gateway> will be set automatically.
3 Enter the password.
The password is the login password of the "admin"
user when connecting to the network decoder.
The default password is "4321".
J
`For the security purposes, you are recommended to use
a combination of numbers, alphabets uppercase and
lowercase and special characters for your password.
4 Click [OK].
Auto network setup will be completed.
※For the IP installer, use only the installer version provided in the installation CD or use the latest one if available.
You can download the latest version from the Hanwha Techwin web site.
Login
The first time you connect after purchasing, the ID is "admin" and the password is "4321".
1 Enter "admin" in the <User name> input box.
2 Enter "4321" in the <Password> field. The password
setting window appears for the first time. If you have
changed your password, enter your new password.
3 Click the [OK] button. When login is complete, the
video wall setup screen appears.
※For security, be sure to change the password in
<User>-<Administrator> in the setting screen.
※If you enter a user name and password, and then
check the ‘Save password in the password list’
checkbox, the user name and password will be
automatically set for the next time you connect.
J
`Internet Explorer will display the image best when the aspect ratio is 100%. If you reduce the aspect ratio, the screen may appear
to be ‘cut off’.
`You cannot double-login with the "admin" account.
`It takes about five minutes after you disconnect from the “admin” account to access the user account.

4
Video wall configuration guide
1 Monitor output for each decoder after the set boots 2 Configure the video walls and allocate monitors. 3 Registering camera
G
RS485
G
1 2 3 4 5 6 7 8 9 10
1112 13 14 15 16
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COM COM COM
NC
G G
NATWORK
NETWORK RUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
CONSOLERUN
HDMI 2HDMI IN HDMI 1
VGA 2 VGA 1
VIDEO OUT
(VGA/HDMI)
VIDEO OUT
(VGA/HDMI) 
a
c
d
b
aCreate video walls.
bAdd video walls (Wall 01 2x2, Wall 02 2x4)
cAssign monitors
dCheck the actual connected monitor index
(Show index : monitor number check, Hide index : video mode)

a
c
b
d
aAdd a camera
bAdd cameras with automatic/manual registration
cSelect the camera list sort function
dSort by name()/IP or ascending()descending.
4 Setting Video Wall Layout 5 Monitoring by video wall
a
c
b
d
aSpecify the monitor of the corresponding video wall to be
applied by clicking it
b
Select and apply a split mode to the selected monitor (Can
be applied to each monitor)
c Assign it to the corresponding tile with the mouse in the camera list
dAfter saving the layout, add a new layout and repeat steps 1 - 4

Monitor 1
Wall 1 Wall 2
Monitor 2
Monitor 1 Monitor 2
aMonitor 1 assigned to Wall 01 (2x2)
bAssign cameras to 3x3 split mode in layout settings
`When this is [ ] clicked, the video wall is enlarged to full screen.
When this is [ ] clicked, the video wall zoom changes to the original size.
c3x3 video output on the actual monitor #1

5
Use product information
You can check product information/manual/firmware information/FAQ through homepage or mobile web on your
smartphone.
http://hanwha-security.com
http://hanwha-security.com
SPD-1660R
SPD-1660R
SPD-1660R_datasheet_170629.pdf
SPD-1660R_CAD_170321.dxf
SPD-1660R_CAD_170321.pdf
SPD-1660R_AE_170717.doc
G
RS485
G
123 4 5 6 7 8 9 10
111213141516
NO NO NO NO
COM
NO
COM
NO
COM
NO
COM
NO
COM
RESET
COMCOMCOM
NC
G G
NETWORK
NETWORKRUN POWER
USB 1 USB 2
AUDIO CONSOLE
RESET
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide
customers with more environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates
that the product satisfies the EU RoHS Directive.

Head Oce
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : [phone] Fax : [phone]
http://hanwha-security.com
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free : +1.877.213.1222 Direct : +1.201.325.6920
Fax : [phone]
www.hanwhasecurity.com
Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel : [phone] Fax : [phone]
www.hanwha-security.eu
Hanwha Techwin(Tianjin) Co.Ltd
No.11, Weiliu Rd., Micro-Electronic Industrial Park, Jingang Road Tianjin 300385, China
Tel : [phone]
www.hanwha-security.cn
Hanwha Techwin Middle East FZE
JAFZA View 18, 20th oor, oce 2001, 2002, 2003, Downtown Jebel Ali,
Dubai, United Arab Emirates
http://hanwha-security.com