Wize WR-15CL User manual

Screen size : 15.6 inch
Signal input : HMDI, VGA
Tilt angle :0-80 degrees,adjustable
Touch function: optional
WR-15CL
Flipped-up LCD
monitor lift
User manual

1.List .Shape and Panel Key Description
1.1 Packing list
No.: Items 备注说明
1 LCD monitor lift 1pc
2 Power cable 1pc
3 VGA cable 1pc
4 User manual 1pc
1.2 Panel key Functions
No.: English Signal
1 STOP
2 UP
3 DOWN
4 PC SW
5 SA SW

1.3 Interface board Function（from left to right）
1.3.1 HDMI Video signal input.。
1.3.2 DVI Video signal input。
1.3.3 VGA Video signal input。
1.3.4 Audio signal input(3.5mm stereo)。
1. 3. 5 Audio signal output(3.5mm stereo).
1.3.6 USB input,up for USB put, down for the touch screen control card
interface。
1.3.7 RS485 control input(1,2,5)
1.3.8 RS485 control input ( for cluster control)
1.3.9 ANT,Remote control receiver antenna（315MHz）。
1.3.10 Standby button interface: PC SW computer start button. SA SW
signal switching key.
1.3.5 AC220V Power input socket .
1.4 Control Introduction：
1.4.1 RS485 Software Control:9 holes interface with the
computer serial port. 232/485 intermediate bridge converter

1.4.2 Remote control：（ Will be give with goods when customer
requested)
1.4.3 Control Button：（ Please see Panel Key function, Red means
light power indicator)
1.4.4 Screen button function：（ Pls see the 7 point, screen menu to
adjust the guide）
Auto ▲
▲
Menu Led
“Menu” menu button，“Auto”Automatic adjustment button，“
▲
”Variable
increment key，“
▲
”Variable reduced key，“ ”Screen Power Switch button。
“LED”Power indicator（Red means no have signal,Green means have signal)
1.4.5 Sub-panel key function:
PC SW，SA SW Standby key for using，USB Standby
connector，it can be straightly link to the connectors on the
connect plate.

2. Structure Features and MainTechnical Indicator
2.1 Structure Features
The part of screen Lift is adopt bilateral synchronous belt wheel with
linear optical axis transmission and low noise and stable structure.。Screen
frame is pure aluminum with tempered glass and nice outlooking .
2.2 Main Technical Indicator：
2.2.1. The Lift Technical Data
Nn. Item Data
1 Working Voltage AC 220V 50Hz
2 Consumed power ＜60W
3 single-working time 18S
4 Elevation angle ≤80
5 Product weight 10Kg
2.2.2
No. Item Data
1 Signal Type LVDS
2 Display Size 15.6
3 Resolution 1920*1080
4 Aspect Ratio 16:9
5 Contrast 650:1
6 Brightness 300

7 Viewing angle 70/70/60/60
8 Video signal mode VGA/DVI/HDMI
3. Structure dimensions and install instructions：
3.1 Structure dimensions：
3.2 Cutting out size：

3.4.4 Connect the touch USB Cable(not need to connect the touch
USB cable if without touch function).
3.4.5 If need Central-controlled system,please connect the RS485
with the control cable.
3.4.6Connect the antenna base with the antenna .
3.4.7 Link to AC220V power supply, The panel indicator light is on,
then press UP key to complete the automatic elevation, the screen lights up,
and the red indicator means no signal, the green indicator means signaled.
4. Technical data：
4.1 HEX system controlling code
All up FF AC E1 FF 00 00 DD 01 DC
All Stop FF AC E1 FF 00 00 CD 01 CC
All down FF AC E1 FF 00 00 ED 01 EC
4.2 Computer software control
4.2.1 Download the control software "Multi functional lifting
equipment Control Center" from the company's official
website.。
4.2.2 Prepare a RS232-485 or USB-RS485 protocol converter.
4.2.3 Using Windows XP systems to install the software.
4.2.4 Make sure the LIFT equipment finishe the connecting 。
4.2.5 Operating according to the assist files of the software.
3.4 Install instructions：
3.4.1 Before setup,please remove two "fixing screws" on the cover
and clean the foam filler inside of the clamshell .
3.4.2 Embedded the lift case inside the cutting in the table ,make
the panel level with the table top.
3.4.3 Connect the Video Signal Cable（VGA or HDMI or DVI).

5. Solutions for the monitor common problems：
No.: Common problems Analysis reason
5.1 The screen is light but No
Display ·please check the Power switch if it is
turned off?
··The Signal is interrupted?
5.2 The word is blurred ··Please check if it matches the resolution
of the computer?
··Please check the contrast and brightness
adjustments if they are correct？
5.3 The Screen is black.
·Automatical black because of no signal ?
·Brightness adjustment is too lowest ?
·If press "Auto" key a long time ,it would
be shutdown, and the LED indicator turns
red.
6. Solutions for the lift common problems:
6.1 All the lift is no power,the indictor light does not work:
Open the Insurance cover of power to check if the fuse is damage? If yes,
please change a new 3.15A fuse.

6.2 Solutions for the main board common problems：
6.1.1 Please check if the lock screws of the AC IN (3P terminal)
power input cable is loose? If yes, please refixed them .
6.1.2 If 5P cable of the Key board does not connect well , it would
cause the indocator light and the buttons out of working, It
seems like no power. Please connect it again.
6.1.3 The checking solutions mentioned above, you can process
it without the case open ,but it must check by a multimeter if
there are around 3.4K resistance value at L and N terminals
of the power input socket. If yes, then the AC current loop is
normal (including transformers, fuses).
6.1.4 If the main board don’t show 12V ,it means it is abnormal,
please check if RL1 is damage.
6.1.5 If the main board don’t show 5V ,it means it is abnormal,
please check if L7805 is damage.
6.1.6 If the main board don’t show 3.3V ,it means it is abnormal,
please check if 7533 is damage.
6.1.7 Up -limited switch is the pulse level control, after the pulse
finished, it still keeps in stop. But the display power is
required to maintain the shading by the photoelectric
control.
6.1.8 Down- limited switch is the low pause control, it will
continue to decline under the high ,so when the decline is
finished, the photoelectric control should be under the
light-shading state.

6.3 Circuit schematic diagram ：

7. Screen menu (the guide of adjustment)
7.1 Color adjust：
Pic t ur e
1920 * 1080 60 1Hz@ .
OSD
OS D
Brigh tn ess
Con tra s t
Gamm a
Press “Menu” Button into the display adjustment,and Press “Menu” button to
make the cursor moveing to the “brightness”. Then Press“
▲
”button,the cursor
moves to the “contrast”.If it needs to be back,please press”Auto” button.
Pressing”Menu”button,it will display the brightness value:
50%,and then press button“▲” or “
▲
” to change the brightness value.
7.2 Image adjust：
Po sitio n
Ph as e
H.po s itio n
1920 *1 080 6 0 1Hz@ .
OS D
OSD
Clock
V.p os it i on
First pressing “Menu” button, and press“▲” button to the image
adjustment, and then press “Menu” again, the cursor can move to the
automatic adjustment image.If it wants to go back, please press”Auto”button.

7.3 Color setting：
Col o r
C Tol o r em pe ra t ur e
Red
Gre n
1920 * 1080 60 1Hz@ .
OS D
OSD
Blue
Press“Menu”button ，and then press“
▲
”twice to
“color” .Press“Menu”button moving cursor to color temperature。
Press“Auto”for back。Press“Menu”button ,you can choose 5000K／
6500K/7500K/8200K/9300K。
7.4 Menu adjust：
OS D
Hor i z on t al
Ve rt i ca l
Tra ns pa ren cy
1920 * 1080 60 1Hz@ .
OSDOS D
O T OS D im e u t
To press “Menu” button, and press “▲” button three times to
display menu。Press“
▲
” button, the cursor move to the H Position.If it
needs to be back, please press “Auto”Button. Press“
▲
” or “ ▲” button,
it can change the alternating of H Position .

Set up
Lang ua g e
Mu te
In pu t
1920 * 10 80 60 1Hz@ .
OS DOSD
OSD
DC R
Di spl ay S i z e
Reset
To press “Menu” button, and press “▲” button or “
▲
”button four times to
display “Set up”.and then Press “Menu”Button to move the cursor to the
“Language”,it can change the language.Press”
▲
” move the cursor to
“mute” .Press”Auto”button fpr back step.Press”menu” for language
setting.Press“▲”“
▲
”moving the cursor to set up“language”.
7.6 Language switch:
Remark: “Auto” button is a signal selection button when it is
used independently, with the selection orde is "VGA", "DVI", "HDMI". When it
is used as the auxiliary, it is a return button.
7.5 Language setting: