WLIVE ACJ009 User manual

Wood Lift Coee Table
ACJ009
[email protected]om
V3.2

GENERAL GUIDELINES
WARNINGS
Please read the following instruction carefully and use the product accordingly.
During assembly, keep parts and packaging materials away from children and pets as there
could cause injury and are a potential choking hazard.
Avoid sharp objects or corrosive chemicals to prevent damage to the product.
Please open the item slowly and cautiously to avoid pinching your hands by metal joints,
especially children.
If an odor is present when first opening the package, please leave the unwrapped product in
a shaded and ventilated area for a few days to air out.
Please follow the assembly instructions precisely and only use the product as intended.
Prior to assembly, please check the product for defects or missing accessories. If any
defects are found or accessories are missing, do not use product as damage or injury
may occur;
Please contact us for assistance and replacement.
It is suggested you regularly check the products bolts and connections to ensure safe use.
Assemble the item on a soft flat and clean surface to avoid scratches and damage.
It is recommended that two people assemble this product.
Please keep this manual and hand it over when you transfer the product.
This summary may not include every detail of all variations and considered steps.
Please contact us when further information and help are needed.
•
•
•
•
•
•
•
•
•
•
•
•
IMPORTANT INFORMATION
READ CAREFULLY.
KEEP THIS INFORMATION FOR FURTHER REFERENCE.
NOTES

If you have any further questions, please feel free to contact us
by email or official website: [email protected]
We will reply ASAP.
Enjoy your new purchase!
Before installation, please make sure you have all the hardware,
the serial numbers are properly labeled corresponging to the list,
and the quantity is correct.

X12 X10
B
X12
C
A
X1 X1
E
D
X12
F
X4
G
X48 X10
I
X4
J
H
X1 X1
L
KX4
M
8
9
76
653
4
2
1
1
1
1
EXPLODED DRAWING
PARTS
1

×12
×10
6
6
X12
A
8
X10
B
57
3
REMARK
Put a blanket under the board to avoid
scratch or damage.
Please do not screw too deep or too shallow.
A
Too deep Too shallowAppropriate position
1.
2.
A
B
1
2
DEV
V
ISE
2

Please do the same for part installed on part 7 .
×16
7
5
5
X16
H
X1
DX1
E
Loosen the screw nut first.
X1
L
D
5
1.
2.
D
L
5
E
3
4
REMARK
3
H

X12
HX1
L
long short
Please tighten the screw nut after all the part are installed.
H
X8
C
9
7
5
6
6
9
7
5
long
short
9
6
7
5
6
C
C
C
6
9
7 5
5
6
REMARK
H12
C×8
L
4

X20
H
X4
G
G
×10
Fully tighten all the screws after all the
screws are in right place.
X1
K
X10
I
2
7
6
3
653
2
G
G
G
7
8
REMARK
I
5
×20
H

X4
M
8
9
The two top plates are cut from a whole board.
Make sure arrows on part 8and 9point to each other.
1
1
1
1
1
63
2
6
6
3
2
8
9
M
MM
M
9
10
REMARK
REMARK
6
Please wait for 3 minutes until it glues completely.

X4
J
X4
C
8
6
×4
3
3
9
6
8
9
11
12
C4
J
7

4
Please make the groove on part 4match with the part .
J
F
×12
X12
F
13
14
REMARK
F
8