WLIVE ASNG015 User manual

ASNG015
SW 2 Drawer Storage Cabinet
[email protected]
V2.0

During assembly, please only slightly tighten all screws in their correct position first, then fully tighten
them. A Philips screwdriver is recommended but not included.
GENERAL GUIDELINES
WARNINGS
Please read the following instruction carefully and use the product accordingly.
During assembly, keep parts and packaging materials away from children and pets as there
could cause injury and are a potential choking hazard.
Avoid sharp objects or corrosive chemicals to prevent damage to the product.
Please open the item slowly and cautiously to avoid pinching your hands by metal joints,
especially children.
If an odor is present when first opening the package, please leave the unwrapped product in
a shaded and ventilated area for a few days to air out.
Please follow the assembly instructions precisely and only use the product as intended.
Prior to assembly, please check the product for defects or missing accessories. If any
defects are found or accessories are missing, do not use product as damage or injury
may occur;
Please contact us for assistance and replacement.
It is suggested you regularly check the products bolts and connections to ensure safe use.
Assemble the item on a soft flat and clean surface to avoid scratches and damage.
It is recommended that two people assemble this product.
Please keep this manual and hand it over when you transfer the product.
This summary may not include every detail of all variations and considered steps. Please
contact us when further information and help are needed.
•
•
•
•
•
•
•
•
•
•
•
•
•
IMPORTANT INFORMATION
READ CAREFULLY.
KEEP THIS INFORMATION FOR FURTHER REFERENCE.
NOTES
Serious or fatal crushing injuries can occur from furniture tip-over. To prevent this furniture
from tipping over it must be permanently fixed to the wall.
Since different wall materials require different types of fixing device, for advice on suitable
fixing systems, contact your local specialized dealer.
•
•
ANTI-TIP WARNING

5/16
(8 mm)
1/8
(3 mm)
If you have any further questions, please feel free to contact us
by email or official website: [email protected]
We will reply ASAP.
Enjoy your new purchase!
Before installation, please make sure you have all the hardware,
the serial numbers are properly labeled corresponging to the list,
and the quantity is correct.

X2
1
1
2
3
4
6
5
7
8
9
11 11
12
13
15
14
16
17
18
10
1
EXPLODED DRAWING

+
=
+
+
X32
M6x30
X4
E
M4x14
X4KX16 L
X16B
X2
D
CL
G1 G2
DL
DR
CR
X2
X1
X3
X32
C
M6x40
X8
F
X1H
X4
M
X4P
X20
J
M3x14
N
M4
X1
O
G
I
A
X1
QX4
R
2
PARTS

CR
DR
CL
DL
3
MINIFIX POSITION
REMARK

1
1
3
32
2
2
X1
O
X4E
X4
P
M6x30
X1
O
X8F
M6x40
Please don't fully tighten screws F.
UP
The holes on part 2should face up.
6
2
2
Please wait for 3 minutes
until it glues completely.
Please fully tighten all screws after
screws E and Fare in place.
Put a blanket under the board to
avoid scratch or damage.
1.
2.
3.
1
2
REMARK
REMARK
×8
F
×4
E
×4
P
1.
2.
4

4
6
5
X8
X4
B
A
X4A
3
4
REMARK
Please do not screw too deep or too shallow.
A
Too deep Too shallowAppropriate position
DEV
V
ISE
214/
A4
×8
B
×4
A
5

45
M4x14
JJ
CL
JJ
X1
CL
X4
J
X1
CR
CR
1
2
Please do not install the bottom drawer runner part in this step, Otherwise it will not be able
to install the connector housing ( Part C), the bottom drawer runner part is installed in
step 11.
REMARK
When installing, please make sure the screws are flattened, not crooked; Otherwise the
drawers will not be installed perfectly.
1.
2.
CL
311
FRONT
J
TOP
BOTTOM
5
113
6

7
8
X8B
X2A
X2
C
Let the grooves on part
8 be connected to the
groove on part 7.
8
8
7
7
6
7
REMARK
7
A2
B8
×2
C

5
5
5
7
7
7
X4C
Let the grooves on part
4and 5be connected
to the groove on part 7.
10
10
10
4
4
4
8
9
REMARK
8
C4

CL
X4C
X1
CL
X4J
X1
CR
CR
5
5
5
4
4
4
6
6
M4x14
10
11
9
C4
M4x14J
RM3x14

11
11
X2R
X1I
8
magnet
I
I
5
5
4
4
M3x14
12
13
10
R2
M4x14J
RM3x14

9
G1 G2
R
H
X6A
X1
H
X1
G
X2
N
G2
12
X2R
M3x14
14
15
×2
N×2
G1
11
A6
M4x14J
RM3x14

9
9
X6
C
8
8
12
12
12
5
5
4
4
7
9
16
12
C6

X16
A
X8C
G1 G2
X2
G
×2
×2
G1
G1
G2
15
15
14
14
14
16
16
16
17
17
18
13
A8
C4

X8C
×2
×2
15
15
14
16
16
16
17
17
18
19
20
14
C4

DL
X2
DL
X8
J
X2
DR
×2
DR
15
16
16
17
18
M4x14
DR
FRONTFRONT
J
39 FRONT
×4
J
FRONT
21
15
111

X4M
17
17
22
23
×4
M
16

X16
L
short
long
The long shadow part is
in front and the short one
is inside.
Please make the groove
on board 13 match with
the part M .
13
13
13
24
25
×16
L
17
REMARK
REMARK