Wolf MWD24-2 Service manual

Drawer Microwave (Models MWD24-2 / MWD30-2)
Installation Information
2-2
#813632 - Revision B - December, 2009
INSTALLATION INFORMATION
Below are the Product Safety Labels used in this manual. This section of the manual covers some of the installation
issues that a service technician may need to know when servicing a Wolf Drawer Microwave. If additional installa-
tion information is needed, after reviewing this section of the manual, please refer to the installation guide or contact
the Wolf Appliance Customer Service Department.
•TO REDUCE RISK OF TIPPING, DRAWER MICROWAVE MUST BE SECURED BY A PROPERLY INSTALLED
ANTI-TIP BLOCK.
•STEPPING, LEANING OR SITTING ON DRAWER MAY RESULT IN SERIOUS INJURIES AND CAN ALSO
CAUSE DAMAGE TO DRAWER MICROWAVE.
•FOR SAFETY CONSIDERATIONS DO NOT INSTALL DRAWER IN ANY COMBUSTIBLE CABINETRY, WHICH
IS NOT IN ACCORD WITH THE STATED CLEARANCES AND DIMENSIONS PROVIDED IN PRODUCT INSTAL-
LATION INSTRUCTIONS.
•NEVER LEAVE CHILDREN ALONE OR UNATTENDED IN THE AREA WHERE A DRAWER MICROWAVE IS IN
USE. NEVER LEAVE DRAWER OPEN WHEN MICROWAVE IS UNATTENDED.
•DO NOT USE DRAWER MICROWAVE AS A STORAGE SPACE. THIS CREATES A POTENTIALLY HAZ-
ARDOUS SITUATION. CHECK THAT THE TIME-OF-DAY IS IN THE DISPLAY. IF NOT, TOUCH STOP/CLEAR
TO PREVENT UNINTENDED USE.
•THIS DRAWER MICROWAVE MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL
CODES.
•DO NOT USE AN EXTENSION CORD. IF POWER SUPPLY CORD IS TOO SHORT, HAVE A QUALIFIED ELEC-
TRICIAN OR SERVICEMAN INSTALL AN OUTLET NEAR THE APPLIANCE.
Electrical Requirements
This appliance must be grounded. The drawer
microwave is equipped with a cord having a grounding
wire with a grounding plug. It must be plugged into a
wall receptacle that is properly installed and grounded in
accordance with the National Electrical Code and local
codes and ordinances. In the event of an electrical short
circuit, grounding reduces risk of electric shock by pro-
viding an escape wire for the electric current.
• 120 volt 60Hz, AC only, 15 amp protected electrical
supply.
• Separate the electrical circuit serving only this appli-
ance.
• A properly grounded 3-prong receptacle
(See Figure 2-1). Figure 2-1. Grounded Receptacle
Neutral
Line Voltage
(Power)
Ground
Ground Prong

Installation Information
Drawer Microwave (Models MWD24-2 / MWD30-2)
2-3 #813632 - Revision B - December, 2009
Clearances and Dimensions
Dimensions shown on this page must be used. Given
dimensions provide minimum clearance. Locate electri-
cal outlet in the shaded area in the upper left hand cor-
ner of the cutout (See Figures 2-2, 2-3, 2-4 & 2-5).
NOTES:
• The drawer microwave can also be installed using
an electrical outlet in an adjacent cabinet within the
area where the provided electrical cord can reach.
Power cord access hole in cabinet should be a mini-
mum of 11/2”(38mm) diameter hole and de-burred
of all sharp edges.
• Always allow sufficient power cord length to the
electrical outlet to prevent tension.
Contact surface must be solid and level. Pay special
attention to the floor on which the drawer microwave will
sit. The floor of the opening should be constructed of
plywood strong enough to support the weight of the
oven, about 100 pounds (45 kg).
Check location where the drawer microwave will be
installed for proper electrical supply.
Your oven can be built into a cabinet or wall by itself or
under a gas or electric wall oven.
Be sure that the clearance of the floor between the wall
oven and the drawer microwave is a minimum of 2”
(51mm).
The microwave interior will easily accommodate a 9”
(229mm) x 13” (330mm) oblong dish or a bag of
microwave popcorn.
15"(381)
Auto Drawer
Opening
15-13/32"
(391)
23-7/8"
(606)
14-19/32"
(371)
23-3/8"(594)
1-1/8" (29)
Door Thickness
21-19/32"
(548)
4-11/16" (119)
1-23/32" (44)
Figure 2-2. 24” Drawer Microwave Dimensions
15-13/32"
(391)
29-7/8"(759)
14-19/32"
(371)
28-1/8"
(714)
4-11/16" (119)
2" (51)
23-3/8"
(594)
1-1/8" (29)
Door Thickness
15"(381)
Auto Drawer
Opening
Figure 2-3. 30” Drawer Microwave Dimensions
22-1/8"(562)
Opening
19"(483)
to top of floor
6"(152)
5"(127)
4"(102)
Allow
3/16"(5)
Overlap
14-13/16"
(376)
Opening
Allow
7/16"(11)
Overlap
23-1/2"(597) Depth Min
Anti-Tip Block
3-1/2"(89)
Allow 7/8"(22)
Overlap
36"(914)
Countertop
Height
14-13/16"(376)
to bottom of
anti-tip block
24"(610)
Cabinet Min
Floor must support
100lbs.(45 kg)
Electrical Outlet
Location
Figure 2-4. 24” Drawer Microwave Install
Specifications

Drawer Microwave (Models MWD24-2 / MWD30-2)
Installation Information
2-4
#813632 - Revision B - December, 2009
Drawer Installation
Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet.
Carefully guide the drawer into the prepared opening. NOTE:Avoid pinching the cord between the oven and the
wall. Slide the drawer all the way until the mounting flange is flush with the face of the cabinet. With the drawer
open, use the four mounting holes on the drawer as a template. Pre drill the cabinet using a 1/16”(1.6mm) drill bit.
Then, secure the drawer with the four mounting screws supplied (See Figure 2-6).
2"
(51)
Min
6"(152)
Electrical
Outlet
Location
Wall Oven
Cutout
Anti-Tip Block
Floor must support
100lbs.(45 kg)
19"(483) to top of floor
(recommended)
84"
(2134)
Wall
Cabinet
A = Allow 3/4"(19) Overlap
B = 23-1/2"(597) Depth Min
C = Allow 3/4"(19) Overlap
D = 4"(102)
E = 5"(127)
F = Allow 7/16"(11) Overlap
G = 14-13/16"(376) Opening
H = Allow 3/16"(5) Overlap
30"(762)
Cabinet Min
28-7/16"(722)
Opening
A
BC
D
E
F
3-1/16"
(78)
14-13/16"(376) to
bottom of anti-tip block
G
H
Figure 2-5. 30” Drawer Microwave Install Specifications
Figure 2-6. Drawer Microwave Installation (MWD24 shown)
6"(152)
19"(483) to top of floor
(recommended)
36"
(914)
Countertop
Height
14-13/16"(376)
to bottom of
anti-tip block
Anti-Tip
Block
3-1/2"
(89)
Electrical Outlet
Location
A = 23-1/2"(597) Depth Min
B = Allow 3/4"(19) Overlap
C = Allow 7/16"(11) Overlap
D = 14-13/16"(376) Opening
E = Allow 3/16"(5) Overlap
30"(762)
Cabinet Min
28-7/16"(722)
Opening
Allow 3/4"(19)
Overlap
A
4"(102)
B
5"(127)
Floor must support
100lbs.(45 kg)
C
D
E
Slide drawer all the way back until
mounting flange is flush with face of
cabinet. Being careful not to pinch
cord. With drawer open, use
mounting four holes as a template.
Pre-drill mounting holes
then, secure drawer with
four screws supplied.
Two on each side.
Mounting Flange
Mounting Screw