Wolf ICBDD30 User manual

DOWNDRAFT VENTILATION
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN
INSTRUCTIONS D’INSTALLATION
ISTRUZIONI PER L’INSTALLAZIONE
INSTALLATIONSANWEISUNGEN

ENGLISH 4
ESPÃNOL 18
FRANÇAIS 32
ITALIANO 46
DEUTSCH 60
3

As you follow these instructions, you will
notice WARNING and CAUTION symbols.
This blocked information is important for the
safe and efficient installation of Wolf equip-
ment. There are two types of potential
hazards that may occur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights informa-
tion that is especially relevant to a problem-
free installation.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
states a hazard that may cause serious
injury or death if precautions are not
followed.
WOLF
®
is a registered trademark of Wolf Appliance, Inc.
CONTACT
INFORMATION
Website:
wolfappliance.com

INSTALLATION REQUIREMENTS
IMPORTANT NOTE: This installation must be
completed by a qualified installer or Wolf
authorized service center technician.
Installer: Please read the entire Installation
Instructions prior to installation. Save these
instructions for the local inspector’s refer-
ence, then leave them with the homeowner.
Homeowner: Please read and keep these
instructions for future reference and be sure
to read the entire Use & Care Information
prior to use.
Any questions or problems regarding the
installation should be directed to your dealer
or visit our website, wolfappliance.com.
IMPORTANT NOTE: This appliance must be
installed in accordance with National Electrical
Codes, as well as all state, municipal and local
codes. The correct voltage, frequency and
amperage must be supplied to the appliance
from a dedicated, grounded circuit which is
protected by a properly sized circuit breaker or
time delay fuse. The proper voltage, frequency,
and amperage ratings are listed on the product
rating plate.
Record the model and serial numbers before
installing the downdraft ventilation system.
Both numbers are listed on the rating plate,
located above the airbox on the front side of
the unit. Refer to the illustration below.
BEFORE YOU START
Proper installation is the responsibility of
the installer.
Check with local utilities for electrical codes
that apply in your area. Local codes vary.
Installation, electrical connections and
grounding must comply with applicable
codes.
This appliance must be properly grounded.
Refer to Electrical Requirements on
page 7.
Make sure you have the tools and materials
necessary for proper installation.
Any required service must be performed by
a Wolf authorized service center. Wolf is not
responsible for service required to correct a
faulty installation.
WOLF DOWNDRAFT VENTILATION SYSTEMS
RATING PLATE
INFORMATION
Model Number
Serial Number
Rating plate location
Location of
rating plate
(behind filters)
5

OVERALL DIMENSIONS
MODELS ICBDD30I AND ICBDD30R
Overall Width 762 mm
Width of Chimney 667 mm
Overall Height (above countertop) 230 mm
Overall Depth 60 mm
Depth of Chimney 38 mm
MODELS ICBDD36I AND ICBDD36R
Overall Width 914 mm
Width of Chimney 819 mm
Overall Height (above countertop) 230 mm
Overall Depth 60 mm
Depth of Chimney 38 mm
6
WOLF DOWNDRAFT VENTILATION SYSTEMS
DOWNDRAFT VENTILATION
IMPORTANT NOTE: Wolf downdraft ventila-
tion systems are recommended for use with
Wolf framed induction or electric, gas and
multi-function cooktops. They cannot be used
with unframed induction or electric cooktops
and are not recommended for use with the
electric grill, steamer and fryer modules.
A Pro ventilation hood is recommended for
use with Wolf dual fuel ranges, gas ranges
and rangetops.
IMPORTANT NOTE: A downdraft can be
used with sealed burner rangetop Models
ICBSRT304 and ICBSRT366. An accessory trim
kit (810215) is necessary for this installation.
Contact your Wolf dealer for details.
Wolf downdraft ventilation systems are
available in 762 mm, 914 mm and 1156 mm
widths. The downdraft should be at least as
wide as the cooktop.
Models ICBDD30I, ICBDD36I and ICBDD45I
include an 850 m3/hr internal blower. Models
ICBDD30R, ICBDD36R and ICBDD45R are
shipped without a blower assembly and can
be used with a 1529 m3/hr remote blower
(812307), available through your Wolf dealer.
Models ICBDD30I and ICBDD30R
60 mm
762 mm
230 mm 667 mm
38 mm
DEPTH OF
DOWNDRAFT CHIMNEY
914 mm
819 mm
60 mm
230 mm
38 mm
DEPTH OF
DOWNDRAFT CHIMNEY
Models ICBDD36I and ICBDD36R
Model ICBDD30
Model ICBDD36
Model ICBDD45
Dimensions may vary to +
– 3 mm.

7
INSTALLATION INSTRUCTIONS
Models ICBDD45I and ICBDD45R
1156 mm
1048 mm
60 mm
230 mm
38 mm
DEPTH OF
DOWNDRAFT CHIMNEY
ELECTRICAL REQUIREMENTS
Wolf downdraft ventilation systems require a
separate, 240 V 50/60 Hz power supply. The
service should have its own 10A circuit
breaker. The unit is supplied with a 2.5 m CEE
7/7 “Schuko” style Continental European
power cord. The specific location of the outlet
is not critical, as long as it is within reach of
the power cord that is located mid-way, top
and bottom, on the right side of the downdraft.
IMPORTANT NOTE: If Model ICBDD30 is to be
installed in a 762 mm wide cabinet, Model
ICBDD36 in a 914 mm wide cabinet or Model
ICBDD45 in a 1156 mm wide cabinet, the
electrical outlet cannot be located on the back
wall of the cabinet. The outlet can be placed in
an adjacent cabinet within reach of the power
cord. An access hole for the power cord must
be drilled in the cabinet wall.
Choose the electrical location shown in
the illustration below that best suits your
installation.
Location of electrical
914 mm min
FOR MODEL ICBDD36
1156 mm min
FOR MODEL ICBDD45
762 mm min
FOR MODEL ICBDD30
OPTIONAL
ELECTRICAL
LOCATION IN
ADJACENT RIGHT
SIDE CABINET
E
OVERALL DIMENSIONS
MODELS ICBDD45I AND ICBDD45R
Overall Width 1156 mm
Width of Chimney 1048 mm
Overall Height (above countertop) 230 mm
Overall Depth 60 mm
Depth of Chimney 38 mm
Dimensions may vary to +
–3 mm.
IMPORTANT
NOTE
You must follow
all National
Electrical Code
regulations. In
addition, be aware
of local codes and
ordinances when
installing your
service.

INSTALLATION SPECIFICATIONS
Wolf downdraft Model ICBDD30 will fit most
762 mm wide cabinets, Model ICBDD36 will fit
most 914 mm wide cabinets and Model
ICBDD45 will fit most 1156 mm wide cabinets.
It is recommended that oversized cabinets be
used for easier installation. Cabinet backs may
need to be removed.
Wolf downdraft ventilation systems can be
mounted in an island, peninsula or standard
wall location.
The illustration below provides installation
dimensions for all Wolf downdraft models.
Pay careful attention to the areas of potential
interference as noted in the illustration.
IMPORTANT NOTE: To install a downdraft
system and a Wolf cooktop, you must allow for
a minimum 638 mm flat counter space from
front to back. A countertop with a raised lip or
backsplash may not allow enough space for
proper installation. 60 mm of flat countertop is
required behind the cooktop and 44 mm is
necessary between the back edge of the
cooktop and inside of cabinet back.
If downdraft Model ICBDD30 is installed in
combination with with two cooktops or inte-
grated modules, an integrated module support
(8603386) for downdraft ventilation is required.
The integrated module support is not required
for Model ICBDD45.
8
WOLF DOWNDRAFT VENTILATION SYSTEMS
54 mm
489 mm
COOKTOP CUT-OUT
DEPTH
914 mm
60 mm
638 mm min
OF FLAT COUNTERTOP*
8.7 mm
745 mm
COUNTERTOP
TO BOTTOM OF
AIR BOX
457
mm
92
mm
83 mm
127
mm
197 mm
16 mm 64 mm min
WITH NO
RAISED LIP*
*AREAS OF POTENTIAL INTERFERENCE
610 mm min
CABINET DEPTH
44 mm min
BACK EDGE
OF COOKTOP
TO INSIDE OF
CABINET BACK*
181 mm
Downdraft installation dimensions

9
INSTALLATION INSTRUCTIONS
INSTALLATION SPECIFICATIONS
For installation of a downdraft system with a
cooktop, refer to the cooktop installation
instructions for the dimensions of the cooktop,
countertop cut-out and cabinet requirements.
The depth of the cooktop may vary and will
affect the location of the downdraft in the
countertop.
The illustration below provides countertop
cut-out dimensions for downdraft Models
ICBDD30, ICBDD36 and ICBDD45 installed with
a Wolf 762 mm or 914 mm cooktop or combi-
nation of cooktop and/or modules.
IMPORTANT NOTE: For installation of a
downdraft with sealed burner rangetop
Models ICBSRT304 and ICBSRT366, an acces-
sory trim kit (810215) is necessary. Contact
your Wolf dealer for details. To obtain local
dealer information, visit our website, wolfap-
pliance.com.
The control module can be positioned horizon-
tally or vertically and located anywhere within
3 m of the downdraft assembly and a
minimum of 76 mm from edge of cooktop cut-
out. Refer to page 11 for instructions to install
the control module.
IMPORTANT NOTE: The downdraft must be
used with a Wolf-approved control module and
top cover.
COUNTERTOP CUT-OUT
Layout and cut the cooktop cut-out far
enough forward so the downdraft will fit
behind it.
Set the cooktop in place and slide it as far
forward as possible. Center and square the
cooktop with edges of countertop.
Place the plastic template included with the
downdraft against the back flange of the
cooktop and centered. Trace around the
template to mark the downdraft opening.
Remove the cooktop from countertop.
Cut the downdraft opening. Be careful not
to chip the edges of the countertop.
686 mm
FOR MODEL ICBDD30
838 mm
FOR MODEL ICBDD36
1067 mm
FOR MODEL ICBDD45
64 mm min
76 mm
min FOR
CONTROL
MODULE
COOKTOP CUT-OUT
WIDTH
638 mm min
FLAT
COUNTERTOP
SPACE
489 mm
70 mm
COUNTERTOP TOP VIEW
Countertop cut-out dimensions

WOLF DOWNDRAFT VENTILATION SYSTEMS
leveling bracket – flange facing in
leveling bracket –
flange facing out
mounting screws
Downdraft mounting brackets
CONTROL MODULE
The remote-mounted control module and top
cover are included with the downdraft. Also
included are mounting brackets, RJ45 connec-
tor and mounting hardware.
The control module can be located anywhere
within reach of the 3 m power cable and a
minimum of 76 mm from edge of cooktop
cut-out. The remote-mounted control module
is 60 mm x 168 mm and can be positioned
horizontally or vertically in the countertop.
IMPORTANT NOTE: Do not place the module
where it will be in the way of cooking, where
hot pans may be placed or where hot liquids
could be spilled on the controls.
To reduce the risk of burns or ignition of
clothing by reaching across burners,
control module must be mounted at least
76 mm from edge of cooktop cut-out.
DOWNDRAFT INSTALLATION
Set the downdraft into the opening. Extend
the leveling brackets to the floor of the
cabinet so the downdraft sits straight.
NOTE: The leveling brackets can be
removed and reattached in other positions.
The flange of the leveling bracket may have
to face inward in tight cabinet installations.
Refer to the illustration below.
Secure the downdraft to the countertop by
holding the downdraft against the back of
the countertop cut-out and tightening the
two mounting screws (one on each end of
unit) on the underside of the countertop.
Screw the leveling brackets to the bottom
of the cabinet. Tighten the screws holding
the leveling brackets to unit on each side.
10