Wonder Tech W201L User manual

1
1
1.1
Remote Control
With LCD remote control functions introduced.
Power LED
Power switch
Speed comtrol stick Click tumbling
Direction control stick
Rotation around
fine-tuning key
Forward trim
backward trim
Right side of
the fly tuning
Left side of
the fly tuning
Headless button off
Headless button open
Headless mode Description: When the key switch is turned on without a
head, no matter which side of the aircraft pointing, can control the forward,
backward, left and right; when the headless key switch off, into the
conventional flight mode.

2
3.1
2
3
Rechargeable Lithium Battery
2.1 The battery and charging cable, then connect the USB charging cable into the USB port or other access
USB charger computer, and then turn on the power. When light is charging, when the lamp is not lit, said
full.
Starts Off
Power (failure) program
Four axis gyro remote control receiver aircraft equipped with fault protection. This design
is for when the model remote control signal is not received in time, battery power failures
and other faults ensure the motor does not start to achieve protection.
TRANSMITTER BATTERY INSTALLATION
Step 2
Step 1
Push
Slide the battery lid to open
by following the arrow
Please use 4 AA sized batteries, installed
based on polarity indicated case. Do not
mix batteries of different chemistry/spec.
Trasmitter
Remote Calibration
Turn on the power switch of aircraft, the aircraft will be put in a horizontal position, and then turn on the remote
control power on both sides of the operation lever to the direction of the upper left corner, after the aircraft
fuselage lights still flashing, indicating successful calibration. (Pictured above)
Battery lid
1
1

3
Turn on the power switch of aircraft,Motor seat red and blue flashing
lights in front of the double representation.the aircraft will be placed
in a flatposition, the status indicator flashes at this time not to move
the body,so that the gyroscope read midpoint.
Step1
Open the remote control power switch,push the throttle stick
from the lowest to the highest, and then pulled a minimum of
code to complete.
Step2
3.2
Operation and Control
up
down
Accelerator
Rudder
Right rotation
Left rotation
Elevator Four aircraft control forward and backward movement
Note: Avoid control: Control Fou aircraft in need always pay attention when moving slowly
joystick control, remote control aircraft will be lost in the process a little power, so you can
add a little extra to make the throttle axis to maintain a certain in-flight exercises height.
Four aircraft control up and down.
Four aircraft control left and right hand.
ON/OFF

4
4
4.1
Left traverse Right traverse
Note: When you fly the plane toward the
direction of the remote control is the opposite.
Aileron Four aircraft left and right to control
lateral movement.
Sensitivity Settings
This section axis can achieve three modes of operation: low, intermediate, and advanced.
Tap the elevator joystick enter setup mode:
Air Tumbling Skills
The sensitivity can be adjusted by remote control at the fine-tuning button, then press and hold the
elevator for one second to confirm or exit.
Sensitivity larger the value, the faster the reaction axis; contrary slower.
This section by the following axis joystick can do a 360-degree roll flying. In order to perform rolling,
ensuring ground to maintain the axis and 30 degrees, preferably during the operation of the rising
roll model, this is easier to maintain the height of the micro-axis roll.
The current face of the basic movements are skilled when you can play some
thrilling tumbling action,and then click on any rudder upper right comer of the remote
control buttons,the remote emits a continuous sound drops, this time into the 3D
rollover state,then hit the remote control joystick in any direction to achieve 3D
tumbling.
Open the remote control to enter the low-level axis mode (sensitivity up to 40%)
When the remote control to issue a "bit" twice, axis into the intermediate mode (sensitivity up to 60%)
When the remote controller "DDD" three times, axis into advanced mode (sensitivity up to 100%)

5
This section by the following axis joystick can do a 360-degree roll flying. In order to perform rolling, ensuring ground to
maintain the axis and 30 degrees, preferably during the operation of the rising roll model, this is easier to maintain the
height of the micro-axis roll.
Under this advanced axis flight mode is very fast and can perform a variety of tumbling instruction.
If you do not roll, you can choose anti-roll mode: Tap the throttle stick; Please note, you can not roll
axis lithium battery is low.
First, the aircraft flew to a certain height, press the function key on the remote control to roll on the right,
then push the right control lever to roll direction indication (push it forward before the turn after turn after
pushing it, pushing it to the left to turn left to the right to push the right turn) to do a 360-degree roll action.
360

6
Under this advanced axis flight mode is very fast and can perform a variety of
tumbling instruction. If you do not roll, you can choose anti-roll mode: Tap the
throttle stick; Please note, you can not roll axis lithium battery is low.
This four shaft aircraft not each blade is the same, each A or B are
marked on the blade, blade installation please click shown below label
installed correctly. When the blade not installed correctly, four axis
will be unable to take off, or lateral rice or fly.
BLADE INSTALLATION AND REMOVAL
Installation: holding onto the little hat of the
blade, press on the motor shaft
A
A
B
B
A

7
1
2
11
1
1
1
1
1
2
2
3
4
4
5
6
7
8
9
10
9
8
10
7
6
33
4
5
5
1
22
Exploded View
Part Name Part Name
Quantity QuantityNumber Number
Mini Receiver
Motor (clockwise)
Motor (counterclockwise)
Lithium Battery
Motor sets
Cabinet
Blade A
Blade A
Blade B
Blade B

8
1.Remote control and micro-axis can not code
2.Propeller does not rotate, or very slow reaction.
3.Can not roll
4.Axis shaking or vibration during flight, big noise.
（Top view）（Bottom View）
A: Check whether the remote control throttle minimum value. When the boot code
on the stick and do not move to any other fine-tuning.
A: (1) lithium battery is low; (2) the need to re-code; (3) to make axis throttle hit the
lowest landing, pause 3 seconds off again.
A: lithium battery needs to be charged too.
A: Check the motor, chassis and blades are installed correctly.
A: Check the A / B blades are properly installed, the blade is properly installed as shown below.
5.Blades can rotate, can not take off
6.One or more motor does not turn
A: (1) Motor bad, renewal motor; (2) motor wire off, to re-wire;
(3) remote control inside a transistor emitter board burned out, replace it with a
new remote control.
A
A
B
B

9
8.Axis after recalibration is still hovering in the drift.
A: The axis on a horizontal surface, in which the orientation of the pad layers of
paper drift (drift depending on the degree of thickness of the paper), which can
calibrate the accelerometer in a horizontal plane, from the surface to solve the
problem of drift.
Table Accessories
Receiver Motor
Battery USB Charger
Mote Control
Blade
Shell