woodmizer LX100 SW-10 User manual

SW-10
SETWORKS
Operation & Parts Manual
LX100 SW-10 Setworks rev.A1.00
Safety is our #1 concern! Read and understand
all safety information and instructions before
operating, setting up or maintaining this machine.
Form #807
!

4 SW-07doc032018 Table of Contents
Table of Contents Section-Page
SECTION 1 INSTALLATION OF THE SW-10 SETWORKS ON LX100 SAWMILLS1-1
1.1 Magnetic Strip Installation.....................................................................1-2
1.2 Magnetic Sensor Installation.................................................................1-3
SECTION 2 OPERATION 2-1
2.1 SW-10 Controller Panel .........................................................................2-1
2.2 Start-up Settings of the Controller..........................................................2-3
2.3 Operation in Normal Mode ....................................................................2-7
2.4 Controller Operation in Pre-defined Head Return Height Mode ...........2-8
2.5 Remote Mode .......................................................................................2-10
2.6 Pattern Modes.......................................................................................2-11
SECTION 3 TROUBLESHOOTING 3-1
3.1 Setworks Malfunction ............................................................................3-1
SECTION 4 REPLACEMENT PARTS 4-1
4.1 How To Use The Parts List....................................................................4-1
4.2 Sample Assembly...................................................................................4-1
4.3 SW10 SETWORKS ........................................................................4-2

Installation of the SW-10 Setworks on LX100 Sawmills
Installation of the SW-10 Setworks on LX100 SawmillsSW-10doc032018 1-1
1
SECTION 1 INSTALLATION OF THE SW-10 SETWORKS ON
LX100 SAWMILLS
IMPORTANT! Before installing and/or operating the
equipment, make sure the sawmill is set up properly.
WARNING! Before performing any service to the sawmill
control box, turn the key switch to the ”0” position, set the
main switch on the control box in the ”0” position and
disconnect the power cord. If you have a DC sawmill,
disconnect the battery cables. Failure to do so may result in
serious personal injury and/or machine damage.

Installation of the SW-10 Setworks on LX100 Sawmills
Magnetic Strip Installation
1
1-2 SW-10doc032018 Installation of the SW-10 Setworks on LX100
1.1 Magnetic Strip Installation
1. Using the mounting hardware shown below, install the magnetic strip assembly to the
mast.
See Figure 1-1.
FIG. 1-1

Installation of the SW-10 Setworks on LX100 Sawmills
Magnetic Sensor Installation
Installation of the SW-10 Setworks on LX100 SawmillsSW-10doc032018 1-3
1
1.2 Magnetic Sensor Installation
1. Install the magnetic sensor mounting bracket (A) to the motor mount plate (B) and the scale (C)
using the fasteners shown below.
See Figure 1-2.
FIG. 1-2

Installation of the SW-10 Setworks on LX100 Sawmills
Magnetic Sensor Installation
1
1-4 SW-10doc032018 Installation of the SW-10 Setworks on LX100
2. Install the magnetic sensor (A) to its mounting bracket (B).
See Figure 1-3.
FIG. 1-3

Installation of the SW-10 Setworks on LX100 Sawmills
Magnetic Sensor Installation
Installation of the SW-10 Setworks on LX100 SawmillsSW-10doc032018 1-5
1
3. The magnetic sensor should be parallell to the magnetic strip. The distance between
these two components should be no more than 1 mm. To make the adjustment, move the
magnetic sensor and its bracket in the slotted holes shown below.
See Figure 1-4.
FIG. 1-4

Installation of the SW-10 Setworks on LX100 Sawmills
Magnetic Sensor Installation
1
1-6 SW-10doc032018 Installation of the SW-10 Setworks on LX100
4. Place the self-adhesive mounting element (A) on the sensor bracket and secure the cable
(B) from the magnetic sensor (C) using a wire tie.
See Figure 1-5.
FIG. 1-5
A
B
C