woodmizer HR200 User manual

Table of Contents Section-Page
Table of Contents SW-07doc0703171

Single Head Resaw
HR200
Safety, Operation,
Maintenance & Parts Manual
HR200EH11S-1 rev.A5.05
HR200EH15S-1 rev. A5.05
Safety is our #1 concern! Read and understand
all safety information and instructions before
operating, setting up or maintaining this machine.
Form #1000
!

2 SW-07doc070317 Table of Contents
Table of Contents Section-Page
General Contact Information
Branches & Authorized Sales CentersWood-Mizer Locations (North and South America)
SECTION 1 SAFETY 1-1
1.1 Safety Symbols.......................................................................................1-1
1.2 Safety Instructions..................................................................................1-2
Observe Safety Instructions
Wear Safety Clothing
Keep Resaw And Area Around Resaw Clean
Dispose Of Sawing By-Products Properly
Check Resaw Before Operation
Keep Persons Away
Keep Hands Away
Use Proper Maintenance Procedures
Keep Safety Labels In Good Condition
SECTION 2 OPERATION 2-1
2.1 Control Overview ...................................................................................2-1
2.2 Resaw Setup ...........................................................................................2-3
2.3 Replacing The Blade ..............................................................................2-5
2.4 Tensioning The Blade.............................................................................2-6
2.5 Tracking The Blade ................................................................................2-7
2.6 Machine Start..........................................................................................2-8
2.7 Blade Height Setting.............................................................................2-11
2.8 Guide Fence Adjustment ......................................................................2-12
2.9 Water Lube Operation ..........................................................................2-13
2.10 Operation Procedure.............................................................................2-14
SECTION 3 MAINTENANCE 3-1
3.1 Wear Life................................................................................................3-1
3.2 Blade Guides ..........................................................................................3-2
3.3 Sawdust Removal ...................................................................................3-2
3.4 Vertical Mast ..........................................................................................3-2
3.5 Miscellaneous Lubrication .....................................................................3-2
3.6 Blade Tensioner......................................................................................3-3
3.7 Belts........................................................................................................3-3
3.8 Drive Belt Adjustment............................................................................3-4
SECTION 4 ALIGNMENT 4-1
4.1 Alignment Procedures ............................................................................4-1

Table of Contents Section-Page
Table of Contents SW-07doc0703173
4.2 Blade Installation And Tracking ............................................................4-2
4.3 Blade Wheel Alignment .........................................................................4-4
4.4 Saw Head Adjustment ..........................................................................4-10
4.5 Blade Guide Arm Vertical Adjustment ................................................4-11
4.6 Blade Guide Arm Horizontal Adjustment............................................4-12
4.7 Aligning the Blade Guides ...................................................................4-14
4.8 Blade Deflection...................................................................................4-15
4.9 Blade Guide Vertical Tilt Adjustment..................................................4-16
4.10 Blade Guide Spacing ............................................................................4-18
4.11 Blade Guide Horizontal Tilt Adjustment .............................................4-19
4.12 Blade Height Scale Adjustment............................................................4-20
SECTION 5 SPECIFICATIONS 5-1
5.1 Overall Dimensions ................................................................................5-1
5.2 Cutting Capacity.....................................................................................5-3
5.3 Blade Motor Specifications ....................................................................5-4
5.4 V-Belt Sizes............................................................................................5-5
5.5 Dust Extractor Specifications.................................................................5-5
SECTION 6 REPLACEMENT PARTS 6-1
6.1 How To Use The Parts List ....................................................................6-1
6.2 Sample Assembly ...................................................................................6-1
6.2 Blade Guide Assembly, Idle Side...........................................................6-2
6.3 Blade Guide Assembly, Drive Side ......................................................6-3
6.4 Blade Guide Arm Assembly...................................................................6-4
6.5 Blade Wheel Assembly, Drive Side .......................................................6-5
6.6 Idle Side Blade Wheel Assembly ...........................................................6-7
6.7 Blade Tensioner Assembly ..................................................................6-9
6.8 Middle Throat Screw...........................................................................6-10
6.9 Water Lube Assembly ......................................................................6-11
6.10 HR200 Saw Head Safety Decals ..........................................................6-13
6.11 Electric Box & Decals ..........................................................................6-15
6.12 Blade Housing Cover ...........................................................................6-16
6.13 Control Panel ........................................................................................6-18
6.14 Up/Down System Screws ...................................................................6-19
6.15 Manual Up/Down System .................................................................6-19
6.16 Vertical Mast Slide Pads ......................................................................6-20
6.17 Motor Assembly ...................................................................................6-22
6.18 Feed Track Assembly (HR200)............................................................6-23
6.19 Hold-Down Roller Assembly, HR200 .................................................6-25
6.20 Guide Fence Assembly, HR200 ...........................................................6-26