Woodstock Shop FoxD3640 User manual

COPYRIGHT © OCTOBER, 2006 BY WOODSTOCK INTERNATIONAL, INC. REVISED JUNE, 2019 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China#8594JC
Phone #: [phone] • Tech Support: [e-mail] • Web: www.woodstockint.com
Model D3640
Deluxe Tool Table
Instruction Sheet
Introduction
The Model D3640 Shop Fox Deluxe Tool Table (see Figure
1) is designed to give you a solid, stable work surface.
This table has a 700 lb. capacity. The flared steel legs,
bracing top and bottom, and under-table braces provide
a solid foundation for the 14" x 40" x 11⁄4" work surface.
The table top is 33" high, providing a comfortable work-
ing height for a variety of benchtop machinery.
Figure 1. Model D3640.
Figure 2. Machine inventory.
1
2
6
5
43
7
8
If structural parts are missing please contact Woodstock
International for replacements. For the sake of expe-
diency, replacements for non-proprietary parts can be
obtained at your local hardware store.
Inventory (Figure 2)
REF PART # DESCRIPTION QTY
1XD3640001 TABLE TOP 1
2XD3640002 SHORT TOP BRACE 2
3XD3640003 LONG TOP BRACE 2
4XD3640004 LONG LOWER BRACE 2
5XD3640005 SHORT LOWER BRACE 2
6XD3640006 LEG 4
7XD3640007 TABLE BRACE 2
8XD3640008 CORNER BRACE 4
Hardware Bag (Not Shown)
REF PART # DESCRIPTION QTY
9XD3640009 TAP SCREW M5 X 20 32
10 XD3640010 PHLP H D SCR M5-.8 X 12 32
11 XD3640011 EXT TOOTH WASHER 5MM 32
12 XD3640012 HEX NUT M5- .8 32
13 XD3640013 ADJUSTABLE FOOT M8- 1.25 X 28 4

-2-
D3640 Deluxe Tool Table Instructions
Figure 3. Correct positioning of long top
brace, corner bracket and leg.
Figure 4. Completed leg assembly.
Figure 5. Correct placement at corners.
Figure 6. Completed stand assembly.
Assembly
We recommend that you have an assistant help position
the pieces while you assemble the stand.
To assemble the stand, do these steps:
1. Loosely fasten one corner bracket, one long top
brace and one leg using the phillips screws, tooth
washers and hex nuts provided. See Figure 3 for
positioning.
2. Fasten another corner bracket and another leg to
the free end of the long top brace used in Step 1.
Again, refer to Figure 3 for proper positioning.
3. Fasten a long lower brace to the leg assembly
completed in Steps 1-2 (see Figure 4).
4. Repeat Steps 1-3 to build another leg assembly.
5. With the help of an assistant, fasten the short top
braces and short bottom braces to one of the leg
assemblies as shown in Figure 5. The top braces,
legs and corner braces MUST be "sandwiched" exactly
as shown in Figure 5. If they are not, the table top
cannot be properly mounted to the stand.
6. With the help of an assistant, fasten the second leg
assembly to the first. This is best done with the
stand positioned upside down on a workbench (see
Figure 6).
Do not fully tighten stand screws, washers, and hex
nuts until all components have been assembled.

-3-
D3640 Deluxe Tool Table Instructions
To attach the table to the stand, do these steps:
1. Place the table top upside down on a clean surface
to avoid scratching.
2. Put the stand assembly on the table top. Adjust
spacing until even (see Figure 7).
3. Using a pencil, mark the underside of the table
top where the holes are positioned in the corner
brackets and top braces. (For now, do not mark the
two pairs of center holes in the long braces.)
4. Remove the stand, then drill 1/8" diameter holes 3/4"
deep at your marks. Figure 7. Mounting stand to table top.
5. Put the stand back on the table top and position the
holes in the stand over your guide holes. Use the
tap screws provided to mount the stand through the
guide holes.
6. Tighten the frame hex nuts and screw the adjustable
feet into the leg ends. Adjust the feet as needed to
level the table.
Note: If you plan to load your stand to full capacity,
attach the two table braces by completing Steps
7-10; otherwise, assembly is complete.
7. Turn the table upside down and place it on a smooth
surface to prevent scratching.
8. Position a table brace as shown in Figure 8 and, with
the help of an assistant, align its holes with those in
the middle of the long top braces.
9. Mark the position of these holes on the underside of
the table top, drill guide holes at these marks (1/8"
diameter x 3/4" deep), and secure the table brace
with tap screws.
10. Attach the second brace by repeating Steps 8-9.
Figure 8. Table brace position.
Customer Service
For questions contact Woodstock
International Technical Support at (360)
734-3482, or send e-mail to:
[e-mail].
Do not drill farther than 3/4" into the underside of
the table top or you may puncture the table surface.