Workplace 4500 Series User manual

Series 4500
MOBILE TABLE
WITH SWAYBRACE
ASSEMBLY INSTRUCTIONS
For Job No.:
Assembly Tips
 • Do not remove components from cartons prior to assembly, as
components do not bear part numbers. Use packing list to locate each
component by the carton number.
•Sort hardware kits by number. Do not open bags until ready for use.
•Assemble basic unit rst, then add any optional accessories.
Kit #21
4 ea. - 5/16-18 x 3/4" Hex Head
Cap Screws
4 ea. - 5/16" Flat Washers
Kit #38
16 ea. - 5/16-18 x 3/4" Hex Head Cap
Screws
16 ea. - 5/16-18 Serrated Flange Nuts
Kit #81
8 ea. - 5/16-18 x 3/4" Hex Head Cap
Screws
8 ea. - 5/16" Lock Washers
8 ea. - 5/16" Flat Washers
Kit #84
4 ea. - Flat Clips
2 ea. - Z Clips
2 ea. - 1/4" Flat Washers
6 ea. - 1/4-20 x 3/4" Round Head
Machine Screws
3Lit #400-07A (Rev 08/2012)
MODULAR BENCH SYSTEMS
®WORKPLACE SYSTEMS, INC.
562 Mammoth Rd • Londonderry, NH 03053
Call 800-258-9700 •Fax [phone]
INSTALLING THE WORKSURFACE
Important Note: Install any optional "Type A" accessories prior to mounting Top.
(See attached instruction sheets to install optional accessories.)
If unit is equipped with a Conductive Top: See enclosed sheet for additional
information regarding conductive tops.
(Kit #84) Position TOP on
completed assembly, with rear
edge ush with rear of Frame, and
centered over each end. Note: Top
will overhang 2" at each end and 1"
at front
.
Pre-installed metal inserts are
located on underside of Top for
ease in fastening. Secure Top to
Frame with fasteners from Kit #84,
noting that at clips are used at
each end, while "Z" clips are used
at center.
1
FLAT CLIP
Z-CLIP
CONTENTS OF HARDWARE KITS

1
2
ASSEMBLING THE BASIC TABLE ASSEMBLING THE TABLE WITH SWAYBAR
1
Note: Make hardware hand-tight
only until specied.
Important! Make certain all compo-
nents are facing same direction.
Front of Frame bears Workplace name-
plate; rear of Leg Section bears tapped
inserts in outside face of vertical leg
tube.
(Kit #81) Fasten FRAME to
MOBILE LEG SECTIONS,
engaging tapped inserts located in
top horizontal crossmember of Leg
Sections.
(Kit #21) Fasten rear SWAY-
BRACE to rear of Leg Sections,
engaging tapped inserts located in
Leg Sections.
Make certain all components are
properly aligned. Tighten all
fasteners securely.

Kit #38
Remove hardware from rear
base of Leg Sections and dis-
card. With hardware from Kit #21,
mount SWAYBAR to rear base of
Leg Sections as illustrated at right.
Tighten fasteners securely.
(Kit #38) Turn unit upside-down
on protected surface. Mount
CASTERS to base of LEG SEC-
TIONS.
3
4
Mount Top:
See instructions on page 3.
Mount Optional Accessories:
See specic instruction sheets
included within.
2



Kit #81
FRAME
SWAYBRACE
SWAYBAR
Kit #21
Kit #21
Unit As Viewed From Rear
Using the Adjustable Height Feature
Note: Height should be changed in Step 3.
Leg Sections are shipped with a preset workheight
of 34-1/2" (including approx. 1" thick worksurface
and 5" diameter Casters).
To make a height adjustment, remove hardware
from above and below the leg's horizontal cross-
member, adjust leg base/extenders (in 1-1/2"
increments) and replace hardware.
Tighten fasteners securely.