Worx LANDROID L WG792E User manual

INSTALLATION
GUIDE

Installation guide EN P04
Installationsvejledning DK P20
Asennusopas FIN P36
Installasjonsguide NOR P52
Monteringshandbok SV P68
Original instructions EN
Original brugsanvisning DK
Alkuperäiset ohjeet FIN
Original driftsinstruks NOR
Bruksanvisning i original SV

4
EN
How to install your Landroid®L
The installation of the Landroid
®
L is easy. Depending on the size of your garden, the entire process only
takes a short amount of time. If you are like us, you hate wasting your time to mow your lawn. The
Landroid
®
L will prove to be a great investment, providing you with years of lawn care.
You can watch the installation demo video at www.worxlandroid.com.
The Landroid®L loves to mow
It is designed to mow often, maintaining a healthier and better looking lawn than ever before. Depending on the
size of your lawn, the Landroid
®
L may be programmed to operate at any time or frequency with no restrictions. It
is here to work for you.

5
EN
Preparation
In the box
From your shed
Distance gauge
Hex key
Scissors Hammer
Landroid®LCharging base
Base fixing
nails
Wire pegs
Boundary
wire reel
Connector
Owner’s manual
Warranty
statement
Installation
guide
Spare blades
Power Adaptor
Programming and
trouble shooting
guide

6
EN
Landroid®L's new home-your garden
Let's start by having a closer look at Landroid®L’s new home—your lawn—highlighting the areas where it
can safely go and areas it’s best for Landroid®L to avoid.
When hitting any obstacle that’s rigid, stable and taller than
15cm—such as a wall or a fence—your Landroid®L will simply
stop and re-direct away from the obstacle.
Obstacles that can be hit
Stones that are heavy enough not to be moved by your
Landroid®L can be safely hit. However, if any stone has an
inclined surface that your Landroid®L can climb, you should
either remove it or exclude it from the working area.
Stones
If your driveway is level with your lawn, without any protruding surface,
the Landroid®L can freely run over it. If you'd like the Landroid®L to
avoid it, then only a 10cm* space between the Boundary Wire and the
driveway is needed.
If it’s covered with gravel, you should not allow the Landroid®L to travel
over it, using the distance gauge for spacing in this case, keeping a
45cm* space between the boundary wire and the driveway.
* This is the recommended distance. Use the provided distance gauge
to ensure proper installation.
Driveways
You certainly don’t want your Landroid®L to mow your flowers, or
fall into the water. These areas should be avoided.
Flowerbeds, ponds, pools...

7
EN
If there are roots emerging from the ground, these areas should
be avoided in order not to damage the roots.
Trees
In the case of large bumps or dips, please consider if the blades
could touch the ground; if this is the case, either make the
inclines smoother or exclude those areas from your Landroid®L’ s
operation.
Depressions and bumps
Your Landroid®L has the ability to safely climb slopes up to 35%
(20°), so just avoid anything steeper than this.
Slopes
The Upper Boundary Wire should NOT be placed on slopes
steeper than 35% (20°). The Upper Boundary Wire should have
a distance of at least 45cm between any obstacles. The Lower
Boundary Wire should NOT be placed on slopes steeper than
25% (15°). The Lower Boundary Wire should have a distance of
at least 55cm between any obstacles when it is positioned on a
slope that is 25%.
Placement of Boundary Wire on slopes
Upper boundary wire
Lower boundary wire
Lower boundary
Wire
35% (20°)

8
EN
10cm
45cm
45cm
45cm
45cm
45cm
45cm
>1m
Installation
See details on step 2.2
See details on step 2.1
See details on step 2.3
See details on step
1 & 3
CHARGING
BASE

9
EN
10cm
45cm
45cm
45cm
45cm
45cm
45cm
>1m
See details on step 2.5
See details on step 2.7
See details on
step 2.4

10
EN
First of all, find a spot for the charging base, taking into account the position of your outdoor socket since the charging base only has
a 15m power cord.
NOTE: Make sure the adaptor and the electrical socket are always kept in a dry area.
Your Landroid®L needs to know where to mow. This is why you have to mark its working area with a boundary
wire that will form an invisible fence. This wire will also guide your Landroid®L to its charging base.
If your neighbor also uses a Landroid®L , then you must keep a space of at least 0.5 metres between
your BoundaryWire and your neighbor's.
The charging base should be placed along a straight line, with
the “IN” arrow pointing to the lawn. Allow 2m distance with no
obstacles both front and back of the charging base. If possible,
place the charging base in the shade, as batteries are better
recharged in a cool place.
1.1
Make sure that your Landroid®L can run on a flat area, clear of any
obstacles.
Feed the boundary wire through the tunnel underneath the
charging base.
1.2
1. Placing the Charging Base

11
EN
When pegging the boundary wire for the first time, it is recommended to use a normal lawn mower or a grass
trimmer to cut the grass along the boundary. Then the wire can be laid as close as possible to the ground to
prevent the Landroid®L accidentally cutting the wire. The boundary wire is powered with a very low voltage so
that it is totally safe to people beings and pets.
2. Pegging your boundary wire
NOTE: Keep the boundary wire straight and tight between
the pegs, there should be no slack wire between the pegs.
When laying the boundary
wire, use the distance
gauge to keep a 45cm*
space between the wire
and the boundary.
Each wire peg should be
placed around 80cm apart.
Use the provided distance
gauge to ensure proper
installation.
NOTE: The maximum
permitted length for the
boundary wire is 350m.
2.1
80cm
80cm

12
EN
2.3
If there is an island that sits inside your lawn where you don't want
Landroid®L to go, please follow the path as shown in the picture to
peg your wire.
The wire should run from the perimeter to outline the defined
island and then return back to the perimeter.The boundary wire
between the island and perimeter should be laid close together
and held in place by the same wire peg. During operation, the
Landroid®L will be able to freely pass over this part of the wire.
<2cm
<2cm
2.2
A feature, such as flowers or shrubs that are close to the mowing
boundary, should be part of the boundary as shown in the picture.
10cm
45cm
45cm
45cm
45cm
45cm
45cm
>1m

13
EN
If your lawn has two or more separate areas connected to each
other by a corridor, it should be at least 1 metre wide. If the corridor
is too narrow, please pick your Landroid®L up and bring it to the
other lawn. Landroid®L will mow this lawn without problem, but
you have to bring it back to the charging base when the battery
runs out.
2.7
>90º>90º
<90º
Ensure the Boundary Wire is perfectly straight in each corner, and
the angle of boundary wire is bigger than 90°.
In the case of an obstacle that is level with ground and safe for
the Landroid®L to run over, such as a driveway or path, then only a
10cm* space is needed.
In the case of two islands that are close to each other, it would be
convenient to lay out the wire as illustrated in the picture.
The Landroid®L can travel freely over the boundary wire in
between the islands and the mowing boundary.
2.6
2.5
2.4
10cm
35cm
35cm
35cm
35cm
>1m
10cm
45cm
45cm
45cm
45cm
45cm
45cm
>1m
35cm
>1m
>1m
<1m
<2cm

14
EN
3. Connect the base to the boundary wire
Cut the end of the wire to a length that’s appropriate
convenient for reaching the clamps.
Strip the two ends of the wire.
NOTE: Too long redundant wire may cause the signal problem.
Strip the two ends of the wire.
3.1
When connecting to the charging base there will be an
IN-wire and an OUT-wire, as shown. Connect the IN-wire
to the red clamp of the charging base and the OUT-wire to
the black clamp.
Then close the cover.
NOTE: Please fix the boundary wire around the charging
base firmly with the wire pegs.
3.2
OUT
IN
OUT
IN

15
EN
You can now permanently fix the charging base on the ground
by pressing the supplied Base Retention Pegs with the
supplied Hex key.
NOTE: Make sure the IN-wire is running straight
underneath the center of the charging base.
3.3
Connect the power cord to the adaptor and then to the AC
electrical socket, the LED on the charging base will turn
on. When connecting, align the notch on the power cord
connector (a) with the groove on the adaptor connector (b).
In case the power cord is within the working area, you may
bury it as needed.
Check the LED status to make sure the connection is OK.
3.4
ab
LED light display Status Action
Green light on Boundary wire is connected successfully;
fully charged
/
Green light on, while “outside working
area” shown in the screen at the same
time
Boundary wire is connected in wrong
direction.
Check and reverse two ends of
boundary wire.
Green light flashing Power supply is connected successfully,
while the wire is connected unsuccessfully
Check and connect the wire again.
Red light on Charging /

16
EN
Open the keypad window
by pressing the large red
button on the top of your
Landroid®L.
Press and hold down the
Power ON/OFF key
until the Landroid®L turns on.
Input the default PIN 0000
Press the key and close
the keypad window: your
Landroid®L will now find its
way to the charging base.
Watch the Landroid®L as it
returns to the charging base
and modify the positioning
of the boundary wire if
necessary. When the
Landroid®L successfully
returns to the charging base,
this means the installation has
been successfully completed!
Now your Landroid®L will start
to fully charge.
4.2
• If your Landroid®L is
outside its territory, it
will not move and the
display will indicate
“outside working area”
error. Just move it inside
its territory and repeat
step 4.2
• If your Landroid®L is
inside its territory but
the display says “outside
working area” and the
LED is on, it means you
clamped the boundary
wire ends incorrectly.
Just reverse them.
• Your Landroid®L should
always remain switched
on. If you ever need to
turn it off, then make sure
you place it within its
boundary area before you
switch it back on again.
• Should your Landroid®L
stop operating
unexpectedly, just press
the STOP button, open
its keypad window, press
its ON/OFF key to ON,
correct the problems,
press button, shut its
keypad window.
NOTE: Please refer to the Programming andTroubleshooting Guide for more information.
Warning
4. Turn on and test the installation
Place your Landroid®L inside the
working area, a few meters from
the back of the charging base.
4.1
This is the exciting part where you can turn your Landroid
®
L on for the first time.

17
EN
Programming
Having the installation finished, please refer to the Programming and Troubleshooting Guide included in the packaging to program
the Landroid
®
L .
Ready to go?
The Landroid
®
Lis designed for maintaining your grass at a perfect length during the season, but is not designed for deforesting a jungle.
Before starting it for the first time,
1. You should mow your lawn to the desired height.
2. Make sure the operating area is clear of objects such as toys and branches...
3. Adjust the cutting height to its maximum level for the first mow and then adjust to your preferred lawn grass height.
Next Spring, let your Landroid®L start mowing early, when the grass is still short, so that you can avoid a preliminary grass cut.
20
25
30
35
40
45
50
55
60

18
EN
Keep it sharp
Always wear gloves when adjusting the blades.
The Landroid®L does not cut grass like other mowers. Its Blades are razor sharp on 2 edges and spin
in both directions for maximum cutting capacity. Each blade of your Landroid®L has 2 cutting edges.
Depending on the frequency the Landroid®L mows your lawn, the cutting blades will need to be
rotated periodically for a new cutting edge. If your Landroid®L is programmed to mow the lawn every
day then the cutting blades will need to be rotated monthly for the best mowing results. Each cutting
blade will last up to 2 months when it is programmed to mow every day. When the cutting blades
are dull and worn out, they should be replaced with the spare blades provided with your Landroid®L.
Spare blades are also available at your nearest WORX retailer.
Maintenance
Your Landroid®L is engineered and built to stay outdoors regardless of adverse conditions. Just
periodically clean its deck from grass clipping build ups and your Landroid®L will mow for you
trouble-free, year after year, season after season. Don't wash Landroid®L or Landroid®L charger or
charging station with high pressure water washers.This may cause damage to the machine, battery
or charger.
Write your PIN code here:
Winter storage
Even though it is tough, we would recommend that you store your Landroid®L in your shed or garage
during the Winter. Before storing it, give your Landroid®L a full recharge that will preserve its battery
from damage. You can then disconnect the plug of the charging base. A good tip to prolong the life of
the battery is to periodically re-charge it during the Winter. We'd also suggest that you cover the base
with a nylon sheet in Winter time.
Safety
Your Landroid®L is safe to people beings and pets. First of all, there’s a large clearance between the
outer border of the machine and the blades. Moreover, the tilt sensors will instantly stop the blades if
the unit is lifted from the ground.
Security
Your Landroid®L is protected by a PIN code. This PIN code prevents unauthorised people from being
able to use it. Once it’s taken outside its territory, it will not be possible to re-start it by anyone who
does not know the PIN code.This also means that you will not be able to start your Landroid®L if
you forget your PIN code! We strongly recommend that you write your PIN code here for future
reference. Even better, register your Landroid®L online at www.worxlandroid.com and record your
PIN code there. You'll be able to access your PIN code online any time.
1
2

www.worxlandroid.com