Worx S Basic LANDROID User manual

P02
Owner’s Manual of Lawn Mowing Robot EN

Owner’s Manual of Lawn Mowing Robot EN
2
1. Product Safety
1.1 General & Additional Safety Instruction
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Carefully read the instructions for the safe operation of the machine.
Save all warnings and instructions for future reference.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• The appliance is only to be used with the power supply unit provided with the appliance.
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
SAFE OPERATION PRACTICES
Training
a) Read the instructions carefully. Make sure you understand the instructions and be familiar with the controls and the
proper use of the appliance;
b) Never allow people unfamiliar with these instructions or children to use the appliance. Local regulations can restrict the
age of the operator;
c) The operator or user is responsible for accidents or hazards occurring to other people or their property.
Preparation
a) Ensure the correct installation of the boundary wire as instructed.
b) Periodically inspect the area where the appliance is to be used and remove all stones, sticks, wires, bones, and other
foreign objects.
c) Periodically visually inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged. Replace
worn or damaged blades and bolts in sets to preserve balance.
d) On multi-spindle appliances, take care as rotating one blade can cause other blades to rotate.
e) WARNING! The lawnmower shall not be operated without the guard in place.
OPERATION
1. GENERAL
a) Never operate the appliance with defective guards, or without safety devices, for example deflectors, in place.
b) Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
c) Never pick up or carry an appliance while the motor is running.
d) Remove the disabling device from the appliance.
– Before clearing a blockage;
– Before checking, cleaning or working on the appliance.
e) It is not permitted to modify the original design of robotic lawnmower. All modifications are made at your own risk.
f) Start robotic lawnmower according to the instructions. Never put your hands and feet under the mower.
g) Do not let persons who do not know how robotic lawnmower works and behaves use the mower.
h) Do not put anything on top of robotic lawnmower or its charging station.
i) Do not allow robotic lawnmower to be used with a defective blade disc or body. Neither should it be used with
defective blades, screws, nuts or cables.
j) Always switch off robotic lawnmower when you do not intend to use the mower.
k) Keep your hands and feet away from the rotating blades. Never place your hands or feet close to or under the body
when robotic lawnmower is in operation.
l) To avoid using the machine and its peripherals in bad weather conditions especially when there is a risk of lightning.
m) Dot to touch moving hazardous parts before these have come to a complete stop.
2. ADDITIONALLY WHEN THE APPLIANCE IS OPERATING AUTOMATICALLY
a) Do not leave the machine to operate unattended if you know that there are pets, children or people in the vicinity.
MAINTENANCE AND STORAGE
WARNING! When the machine is stopped for servicing, inspection, or storage, or to change the
blades, remove the key from the machine and make sure that the blades are come to a complete stop.

Owner’s Manual of Lawn Mowing Robot EN
3
a) Keep all nuts, bolts and screws tight to be sure the appliance is in safe working condition.
b) Inspect the robotic lawnmower each week and replace worn or damaged parts for safety.
c) Check especially that the blades and blade disc are not damaged. Replace all blades and screws at the same time if
necessary so that the rotating parts are balanced.
d) Ensure that only replacement cutting means of the right type are used.
e) Ensure that batteries are charged using the correct charger recommended by the manufacturer. Incorrect use may
result in electric shock, overheating or leakage of corrosive liquid from the battery.
f) In the event of leakage of electrolyte flush with water/neutralizing agent, seek medical help if it comes into contact with
the eyes etc.
g) Servicing of the appliance should be according to manufacturers’ instructions.
Recommendation
To connect the machine and/or its peripherals only to a supply circuit protected by a residual current device (RCD ) with a
tripping current of not more than 30 mA.
Residual risks
To avoid injuries, wear protective gloves when replacing the blades.
Transport
The original packaging should be used when transporting robotic lawnmower over long distances.
To safely move from or within the working area:
a) Press the STOP button to stop the mower.
b) Always switch off robotic lawnmower if you intend to carry the mower.
c) Carry the mower by the handle at the rear under the mower. Carry the mower with the blade disc away from the body.
Safety warnings for battery pack inside the tool
a) Do not dismantle, open or shred battery pack.
b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer
where they may short-circuit each other or be short-circuited by conductive materials. When battery
pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal
objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause
burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes.
If contact has been made, wash the affected area with copious amounts of water and seek medical
advice.
f) Seek medical advice immediately if a cell or battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Battery pack gives its best performance when it is operated at normal room temperature
(20°C ± 5°C).
i) When disposing of battery packs, keep battery packs of different electrochemical systems
separate from each other.
j) Recharge only with the charger specified by WORX. Do not use any charger other than that
specifically provided for use with the equipment. A charger that is suitable for one type of battery pack may
create a risk of fire when used with another battery pack.
k) Do not use any battery pack which is not designed for use with the equipment.
l) Keep battery pack out of the reach of children.
m) Retain the original product literature for future reference.
n) Dispose of properly.

Owner’s Manual of Lawn Mowing Robot EN
4
1.2 Information on the Landroid®
WARNING - Robotic lawnmower can be dangerous if incorrectly used.
Read through the Operator’s manual carefully and understand the content before using your robotic
lawnmower.
WARNING - Keep a safe distance from the machine when operating.
WARNING –Remove the disabling device before working on or lifting the machine.
WARNING - Do not ride on the machine.
Do not burn
Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not
dispose of waste batteries as unsorted municipal waste.
Do not dispose of batteries. Return exhausted batteries to your local collection or recycling point.
Do not wash the machine with a high pressure washer
Class III appliance
Waste electrical products must not be disposed of with household waste. Please recycle where facilities
exist. Check with your local authorities or retailer for recycling advice.

Owner’s Manual of Lawn Mowing Robot EN
5
2. Component List
57 64
9
11
14
15
13
17
16
12
18 21 19
20
10
8
1
3
2

Owner’s Manual of Lawn Mowing Robot EN
6
1. PROTECTIVE COVER
2. CONTACT PINS
3. CHARGING BASE
4. CHARGING STRIPS
5. CUTTING HEIGHT ADJUSTMENT KNOB
6. REAR DRIVING WHEEL
7. RAIN SENSOR
8. MAIN SWITCH
9. STOP BUTTON
10. CONTROL PANEL
11. FRONT WHEEL
12. CUTTING BLADE
13. BLADE TURNING DISC
14. BATTERY PACK
15. HANDLE
16. POWER ADAPTOR
17. BOUNDARY WIRE
18. WIRE PEGS
19. CHARGING BASE FIXING NAILS
20. BOUNDARY WIRE DISTANCE GAUGE
21. HEX KEY

Owner’s Manual of Lawn Mowing Robot EN
7
3. Control panel
Start
1) After the boundary wire installation, you can start using the Landroid®(Please refer to Installation guide for boundary
wire installation).
2) Turn the main switch (8) to “I”(on). Wait until the battery indication light stays green. (If Landroid®has low battery
capacity, the battery indication light will stay red.) If the battery is too low, it will not stay red but shut-down to prevent
battery damage (please refer to Battery Life for emergency charge).
3) Press , then press to start mowing.
4) Press and to make Landroid®go to the charging base.
Landroid®will work continuously until reaching low battery power level and then it will return to the charging base. Once
charging is complete, Landroid®will automatically resume mowing or it stay in the charging base according to mowing
schedule.
4. Intended Use
The garden product is intended for domestic lawn mowing. It is designed to mow often, maintaining a healthier and better
looking lawn than ever before. It is not intended for digging, sweeping or snow cleaning.
Battery indication light
Displays battery/machine
status
START
Starts mowing/Corrects
the problem
HOME
Sends Landroid®to its
charging base during
operation and activates
charging
OK
Confirms any setting/
Enters Wi-Fi connection
mode
STOP
Stops Landroid®during
operation
Error indication light
Displays error messages

Owner’s Manual of Lawn Mowing Robot EN
8
5. Understanding Your Landroid®
Congratulations on your new purchase of the Landroid®and welcome to the care-free life of automatic mowing. In the
following, we would like to help you better understand how your Landroid®thinks.
5.1 How does my Landroid®know what to mow?
The Landroid®chooses its direction at random. It will make sure your entire lawn is evenly mowed without leaving
unattractive mowing paths (See Fig. A).
A

Owner’s Manual of Lawn Mowing Robot EN
9
5.2 How does my Landroid®know what to mow?
Your Landroid®is capable of doing things on its own. The Landroid®knows when it needs to go to its Charging Base (3) to
charge, can sense when it is raining, can stop itself if it senses a problem, and knows to stop, draw back, and turn around
when it bumps into something blocking its path. The Landroid®will also automatically stop its Blade Turning Disc (13) from
rotating if it is lifted off the ground to prevent an accident.
A. Finding the charging base
When your Landroid®needs to recharge, it will stop mowing and follow the Boundary Wire (17) in an anti-clockwise
direction back to its Charging Base. Landroid®is pre-programmed to mow the grass near the boundary wire once a week.
By default, Landroid®will mow near the boundary wire at a random time during the next week after it is powered on.
B. Rain sensors
The Landroid®is equipped with a Rain Sensor (7) which detects rain
and tells the Landroid®to stop mowing and follow the Boundary
Wire back to its Charging Base (See Fig. B).
Landroid®will resume mowing after passing the Delay Time. The
default Delay Time is 180mins.
When the rain sensors are wet, the Landroid®returns to its charging
base. The error indication light will flash blue four times per cycle.
When the rain sensors dry, Landroid®will begin the Delay Time
countdown or return to mowing. If you want to exit from the rain
delay, dry the sensor area, and perform a power cycle by operating
the Main Switch. After the power cycle has been performed you can
see that the blue led is not flashing and so you can operate again.
C. Sensing the boundary wire
The Landroid®always obeys the border set by the Boundary Wire and uses sensors at its front to detect it. (See Fig. C).
D. Starting and stopping while mowing (See Fig. D, E1, E2)
If you would like Landroid®to stop mowing, simply press the STOP button (9) on top of the mower. To start mowing, turn
the main switch to “I” (on), wait until the battery indication light stays green. Press , then press . ( If Landroid®has
low battery capacity, the battery indication light will stay red.)
If Landroid®senses something is wrong, the error indication light will indicate the fault message. For information on these
messages, refer to the Error Messages." Landroid®will turn off if it does not receive any input from the user within 20 min.
To resume:
• Turn the Main switch (8) to “O”(off)
• Correct the problem (refer to Error Messages)
• Turn the main switch (8) to “I”(on), Wait until the battery indication light stays green. (If Landroid®has low battery
capacity, the battery indication light will stay red.)
• Press , then press
• Now the Landroid®will begin to mow!
C
DD
B

Owner’s Manual of Lawn Mowing Robot EN
10
E1 E2
“Cut to Edge” Tech
F
5.3 Cut to edge
Off-centered Blade Turning Disc (13) design provides a clean cut
with narrowest distance to the boundary or wall. It helps minimize
the amount and frequency of manual trimming along the boundary.
Additionally, the Landroid® is designed with a protective cover
underneath that prevents objects from touching the turning blades
and/or injury. (See Fig. F)
5.4 Working Schedule
(1) Default Working Schedule
9:00~11:00 everyday (including charging time)
2hrs
Everyday
(2) Tall grass working schedule
For the first mowing when the grass grows very tall after winter or a long holiday, you can change it to tall grass mowing
mode by keep pressing button for 5 seconds until a beep sound is heard. Press then to start mowing.
Landroid®will resume to previous start time and the default working duration in the following days.
Day 1
Day 2
Day 3 2hrs
2hrs
10hrs
(3) Change default start time
The default start time of 9:00 can be changed to anytime by keep pressing both and buttons at the same time
for 3 seconds until a beep sound is heard.
For example, keep pressing both and buttons at 14:05, and your Landroid®will be mowing from 14:05 to
16:05.

Owner’s Manual of Lawn Mowing Robot EN
11
2hrs
Everyday
NOTE: If your Landroid®is shut off, it will resume to default working duration and the start time will resume to previous
setting when the machine is re-started.
NOTE: When you replace the battery, the working duration will resume to default working duration and the start time is
set to the moment when the battery re-connected.
5.5 How efficiently will my Landroid®mow the grass?
Mowing times are different for every lawn depending on the factors mentioned below. Gradually adjust the time you allow
Landroid®to mow each day until you find the most suitable setting.
Your Landroid®is capable of mowing areas of different sizes, although this depends on various factors, such as:
• Species of grass in your lawn and its growth rate
• Sharpness of the Cutting Blades (12)
• Humidity
• Surrounding temperature
• Amount of obstacles in your Lawn
Unlike most other mowers, Landroid®uses a side charging system,
which is able to cut the much surrounding grass as possible.
The holes on the bottom of the charging base allow the grass to
grow through the base to help disguise it and create an elegant
appearance.
The Landroid®’s cutting height can be adjusted between 2cm-6cm.
Before starting your Landroid®for the first time, you should cut the
grass to the height no more than 9 cm. Then, set the cutting height to
its maximum setting, 6cm. (See Fig. G)
Your Landroid®will cut its best in dry weather. Wet grass can build
up on the Blade Turning Disc (13) and within the motor, and can also
cause loose traction and slippage while working.
Your Landroid®is afraid of lightening storms. In case of a lightening storm, protect the Landroid®by unplugging the
Charging Base (3), disconnecting the Boundary Wire (17), and making sure the Landroid®is not allowed to charge.
Your Landroid®loves mowing grass and requires the Cutting Blades (12) to be kept in good condition to cut at its best. The
Landroid®can do most things by itself, but will sometimes need your help to prevent damage to itself.
• Never let the Landroid®travel over gravel.
• Remove or prevent access to obstacles that the Landroid®could accidentally climb on and damage its Blade Turning Disc.
• Remove all debris and foreign objects from your lawn.
6. Boundary Wire Basics
6.1 Pegging the Boundary Wire
Use the Boundary Wire Distance Gauge (20) to set the correct
distance between the wire and the border of your lawn (more than
26cm*).
* This is the recommended distance. The provided distance gauge
ensures proper installation.
If your neighbor also uses a Landroid®, keep a spacing of at least 1
metres between your Boundary Wire and your neighbors.
The Boundary Wire must outline the intended mowing
area exactly. Your Landroid®will become confused by extra bends
or coils of Boundary Wire that are not part of its mowing area (See
Fig. H). If there is excess Boundary Wire after the mowing area
has been outlined, then cut it off and store this additional wire in H
G

Owner’s Manual of Lawn Mowing Robot EN
12
a separate location. It is important to leave the necessary length where it connects to the Charging Base so it can be
connected and still remain buried.
6.2 Burying the Boundary Wire
If you are planning to bury the Boundary Wire, it is recommended to first peg it down. This allows you to easily change the
layout if necessary before burying the wire. When the boundary wire installation is complete, have Landroid®follow and check
the path by pressing and . This will allow Landroid®to adjust to its new environment.
While observing Landroid®you can easily make alterations to the boundary wire to ensure the Landroid®'s trouble-free
tracking when locating the charging station. Confirm that Landroid®docks in the charging station successfully, and bury the
wire if desired.
7. Software update
The software can be updated when new versions become available. The latest software can be our
website www.worxlandroid.com.
Update via USB. See below for download and installation instructions:
(1) Locate the latest software version at: www.worxlandroid.com.
Save the file to an empty FAT32 formatted USB (flash drive).
Delete any other files on the drive and check the format. If the
drive is not formatted in FAT32, please reformat the drive.
NOTE: the software update is downloaded as a zipped file. You
will need to unzip or extract it before proceeding.
(2) Place Landroid®on a secure and level surface. Turn the Main
Switch to the “O” position to turn off your Landroid®.
(3) Lift the rear of the Landroid®to access the underside.
(4) Open the protective rubber cover under the Landroid®to access
the USB port.
(5) Insert the USB drive (flash drive) in the port. (See Fig. K)
(6) Place the Landroid®on the ground again.
(7) Turn the Main Switch to the “I” position to turn on the Landroid®.
(8) The battery indication light will start to pulse. When the error
indication light flashes blue, the file has been copied.
(9) Without lifting the Landroid®, remove the USB drive (flash drive).
(10)The update will begin automatically and may take several minutes. The final alert sequence will include a beep, and both
the battery indication light and error indication light will flash. When the error indication light turns off and only the green
battery indication light remains lit, the update is complete.
NOTE: If the Landroid®is not inside the boundary wire, the error indication light will flash RED after the update. Please
refer to the manual for more information.
(11)Be sure to tightly and completely close the rubber protective USB port cover.
The manual included with your Landroid®is based on the default software at the time of production.Some new features/
functions in the new version may not exist in the manual. If you found some settings not in the manual, please visit www.
worxlandroid.com to download the latest manual.
8. Maintenance
Your Landroid®works hard and needs to be cleaned and checked from time to time. Some parts will require replacement
as they become worn. Never use your Landroid®with defective main switch.
Switch off the machine before carrying out any service or maintenance.
Here's how to take care of your Landroid®.
8.1 Keep it sharp
WARNING: Before cleaning, adjusting, or replacing the Blades, turn your Landroid®OFF and
put on protective gloves.
WARNING: When fitting new blades, make sure you replace ALL the blades. Always use new
screws when fitting blades. This is important to ensure blade retention and balance the blade
K

Owner’s Manual of Lawn Mowing Robot EN
13
turning disc. Failure to use new screws could cause
serious injury.
The Landroid®does not cut grass like other mowers. Its Cutting
Blades (12) are razor sharp on 2 edges and rotate in both
directions for maximum cutting capacity (See Fig. L). Each blade
of your Landroid®has 2 cutting edges. The Blade Turning Disc will
make forward and reverse rotation at random to use both cutting
edges and minimize the frequency of replacing the blades. Each
cutting blade will last up to 2 months when it is programmed to
mow everyday. Always check to see if the Blades are chipped
or damaged and replace them if they are. When the cutting
blades are dull and worn out, they should be replaced with the
spare blades provided with your Landroid®. Spare blades are also
available at your nearest WORX retailer.
A. Replace the Blades
After some time, usually every season, your Landroid®’s Blades
will need to be replaced. When replacing the Blades, make sure
to replace all of them at the same time. You can replace them with
one of the spare Blade kits and extra Blade screws supplied with
your Landroid®.
Before attempting to replace your Landroid®’s Blades, turn the
power off and put on protective gloves and follow these steps:
1. Gently flip the Landroid®over.
2. Remove the battery cover and remove the battery.
3. Take the screws off the Blades with a screwdriver (See Fig. M)
4. Firmly screw on the new Blades.
5. Refit the battery and the battery cover.
IMPORTANT: After screwing the Blade to the Blade
Disc, make sure the Blade is able to spin freely.
8.2 Keep it clean
WARNING: Before cleaning, turn your Landroid®
OFF. Put on protective gloves before cleaning the
Blade Turning Disc (13) and do not rinse or flush with
water.
A. Cleaning the body
Your Landroid®will live a much happier and longer life if it is
cleaned regularly. Although, since your Landroid®is an electric
machine, you will need to take care when cleaning. DO NOT
use a hose, high pressure washers or otherwise pour
running water on your Landroid®.It is best to use a spray
bottle filled with water. When cleaning the machine body, use a
soft brush or clean cloth and avoid using solvents or polishes (See
Fig. N). Lastly, remove all build up of grass clippings and debris.
B. Cleaning the Underside
Again, it is important that you power the Landroid®OFF and wear protective gloves before touching the Blade Turning
Disc (13).
First, flip your Landroid®upside down to expose its underside. Here you will see the Blade Disc, the chassis, and the
Front Wheel (11) and Driving Wheels (6). Clean everything thoroughly with a soft brush or moist rag.
WARNING: NEVER clean the underside of Landroid®with running water. Component damage can occur. (See
Fig. O1, O2)
Rotate the Blade Disc to ensure it rotates freely. Check the blades spin freely around the fixing screws. Remove any
obstructions.
IMPORTANT: Remove any lodged debris so that it does not cause a crack in the Blade Disc. Even the
tiniest crack can decrease your Landroid®'s mowing output.
C. Clean the contact pins and the charging strips
Clean the Contact Pins (2) located on the Charging Base (3) and the Charging Strips (4) located on the Landroid®using a
cloth. Remove any built up grass clippings or debris around the Contact Pins and charge strips periodically to ensure the
Landroid®successfully charges each time.
1
2
L
M
N

Owner’s Manual of Lawn Mowing Robot EN
14
8.3 Battery life
The heart of the Landroid®is its 20V Li-Ion Battery. For proper storage of the battery, make sure it is fully charged and kept
in a cool dry place between (20°C- 60°C).
NOTE: The recommend Landroid®operation temperature is between 0-55°C.
The life-span of the Landroid®’s battery depends on various factors, such as:
• The length of the mowing season in your region
• Amount of hours the Landroid®mows per day
• Battery maintenance during storage
Landroid®can be charged manually without the boundary wire.
1. Connect the Charging Base to a suitable power supply. The green light on the Charging Base will
turn on.
2. Manually dock the Landroid®into the Charging Base while the Landroid®is powered off.
(See Fig. P1)
3. The green light on the Charging Base will turn to red, and the battery indication light will flash
green and red. (See Fig. P2) Landroid®will begin to charge.
8.4 Winter hibernation
Your Landroid®will live longer and healthier if it is allowed to hibernate. So even though it is tough, we recommend storing
your Landroid®in your shed or garage during the winter.
Before you prepare your Landroid®for winter hibernation, we recommend you:
• Thoroughly clean your Landroid®
• Fully charge the battery
• Turn the power off
To maximize the battery life, fully charge the battery before storage during winter.
WARNING: Protect the underside of Landroid®from water. NEVER store Landroid®upside down
outdoors
The Boundary Wire can be left in the ground although its ends should be protected, such as placed in a tin can with grease.
O1
O2
P1 P2

Owner’s Manual of Lawn Mowing Robot EN
15
If the Charging Base is left outside for the winter, leave the Boundary Wire connected.
NOTE: When bringing the Landroid®back to work after winter hibernation, make sure the Charging Strips (4) and Contact
Pins (2) are clean. We recommend using a fine grade emery cloth to clean the contacts.
8.5 Replacing the battery
WARNING: Power off before attempting any adjustment, replacement or repair.
Before replacing the Blades, turn your Landroid®OFF and put on protective gloves.
If you need to replace the Battery, follow these steps:
1. Gently turn your Landroid®upside down.
2. Remove the screws on the battery cover. Remove the battery cover. (See Fig. Q1)
3. Lift out the old battery carefully. Press the latch (a) and release the connectors. (See Fig. Q2)
NOTE: Do not pull by the cables. Hold the connectors and release the latch (a).
4. Connect a new original battery by attaching the connectors until they click into position. (See Fig. Q3, Q4)
5. Fit the battery as shown. (See Fig. Q5) Place the cover back in its position and tighten the screws.
Q5
Q3
Q4
Q1
a
2
2
1
Q2

Owner’s Manual of Lawn Mowing Robot EN
16
9. Function Messages
The battery indication light on the interface of Landroid®indicates the following status:
Battery indication light Status
Green light on Sufficient power for mowing
Red light on Low power, need to recharge
Green light flashing Auto charging
Red light flashing Battery too hot. Wait until the battery cools down.
Error indication light Status
Blue light flashing four times per cycle Rain delay activated.
10. Error Messages
Symptom Cause Action
Red light on
Landroid®is trapped.
1. Turn Landroid®off;
2. Take Landroid®to an area in your lawn free of obstacles;
3. Turn Landroid®on. Wait until the battery indication light stays green. (If
Landroid®has low battery capacity, the battery indication light will stay
red.) Press .
4. If the error message is still displayed; turn power off; turn Landroid®
upside-down. Check if there is anything preventing the wheels from
rotating.
5. Remove any obstruction, turn the Landroid®upright, turn power on.
Red light flashing
twice per cycle
Landroid®is outside
working area.
1. If Landroid®is actually outside its territory: turn Landroid®off, take
Landroid®inside its territory. Turn Landroid®on. Wait until the battery
indication light stays green. (If Landroid®has low battery capacity, the
battery indication light will stay red.) Press .
2. If the Landroid®is inside its territory, check if the LED on the Charging
Base is green. If not, verify that the Charging Base is properly connected
to the charger and that the charger is connected to a suitable power
supply. If they are properly connected, the boundary wires are clamped
incorrectly and must be reversed. Press .
Red light flashing
three times per cycle
Wire missing
If the LED light flashes green, confirm that the boundary wire is well
connected to the clamps on the charging base. If the problem persists,
check that the boundary wire hasn’t been cut. Press .

Owner’s Manual of Lawn Mowing Robot EN
17
Blue light on
Wheel motor blocked
1. Turn Landroid®off; take Landroid®to an area free of obstacles;
2. Turn Landroid®on. Wait until the battery indication light stays green. (If
Landroid®has low battery capacity, the battery indication light will stay
red.) Press .
3. If the error message is still displayed; turn power off; turn Landroid®
upside-down and check if there’s anything preventing the wheels from
rotating.
4. Remove any obstruction, turn Landroid®upright, turn power on.
Blade disc blocked
1. Turn Landroid®off;
2. Turn Landroid®upside down and check if there’s anything preventing
the blade disc to rotate.
3. Remove any obstruction.
4. Turn Landroid®upright and take it to an area with short grass or adjust
the cutting height;
5. Turn Landroid®on. Wait until the battery indication light stays green. (If
Landroid®has low battery capacity, the battery indication light will stay
red.) Press .
Blue light flashing
twice per cycle
Landroid®is lifted up.
1. Turn Landroid®off.
2. Take Landroid®to a lawn area clear of obstacles, turn Landroid®on.
Wait until the battery indication light stays green. (If Landroid®has low
battery capacity, the battery indication light will stay red.) Press .
3. If the error message is still displayed: turn Landroid®off, turn Landroid®
upside-down and check there’s nothing lifted up.
4. Remove any possible object, turn Landroid®upright, turn Landroid®on.
Blue light flashing
three times per
cycle
Landroid®is upside
down.
1. Turn Landroid®off.
2. Turn Landroid®upright.
3. Turn Landroid®on. Wait until the battery indication light stays green. (If
Landroid®has low battery capacity, the battery indication light will stay
red.) Press .
NOTES
• Before turning power on, always return Landroid®to its territory. If not, the error indication light will flash red. This
message is also displayed when Landroid®is sitting over the boundary wire when turned on.
• If for any reason—i.e. a party, children playing...—you want to park your Landroid®in the Charging Base: press and
. Landroid®will go to its charging base and stay there. Landroid®will wait until the next scheduled mowing session.
If you want to re-start it, press and to start mowing.
• If an error repeatedly occurs in the same area of your lawn, you might have a problem with the boundary wire. Please
refer to the previous installation instructions and check your set up with its help.
• If your lawn is divided in two separate areas connected by a corridor less than 1m, one of which is not provided with
the Charging Base: when Landroid®runs out of charge, take it manually to the Charging Base, turn power on by turning
the main switch (8) to “I”(on), press and , the charge process will start.
• If Landroid®runs abnormally once in a while, please try to restart it. If the problem is not resolved, try to removing and
reinstalling the battery. If the problem is still not resolved, please contact a WORX.
• Do not wash the machine with a high pressure washer. This could cause damage to the battery or the machine.
11. Troubleshooting
If your Landroid®does not work correctly, follow the troubleshooting guide below. If the issue persists, contact your Dealer.
Symptom Cause Action
Landroid®turns on, but the Blade
Disc does not move.
Landroid®is searching for the Charging
Base (unless you press the HOME
button to make it go to the charging
base, or the “Enable boundary cut”
function is operating).
This is normal. Landroid®needs to recharge,
the Blade Disc does not rotate while it is
searching for the Charging Base automatically.

Owner’s Manual of Lawn Mowing Robot EN
18
Landroid®vibrates. Blades may be damaged. Check
condition of the Blade Disc.
Check the Blades, and replace them if
damaged.
Remove debris and foreign objects from the
blades and blade disc.
Grass is being cut unevenly.
Landroid®does not work enough hours
per day.
Add more hours to the scheduled mowing
time.
Mowing area is too big. Try decreasing the size of the mowing area or
adding more hours to the mowing time.
Blades are dull. Change all the Blades and screws in order to
balance the Bade Disc.
The cutting height is too low for the
length of the grass.
Raise the cutting height and then gradually
lower.
Grass or other object has wrapped
around the blade disc.
Check the Blade Disc and remove the grass
or other object.
There is a build-up of grass in the Blade
Disc or Motor Frame Box.
Make sure the Blade Disc rotates easily. If
need be, you may take off the Blade Disc and
remove the debris.
Your Landroid®is inside its
territory and the boundary wire
is connected. The error indication
light flashes red.
The boundary wire ends are clamped
incorrectly. Reverse the boundary wire ends.
The charging time is far more
than 2h.
Poor connection caused by debris on
the Charging Strip.
Clean the Contact Pins located on the
Charging Base and the Charging Strip on
Landroid®using a cloth.
The charging protection program has
activated due to high temperature.
Place the charging base in a shady area or
wait until the temperature has cooled down.
The mower does not charge.
There is no power.
Check the power cord is connected properly
to the charger and the charger is connected
to a suitable power supply.
Does not operate correctly while
manually charging. Refer to manual charging.
Landroid®is starting to have
shorter run-times between
charges.
Something is clogging in the Blade
Disc.
Take off the Blade Disc and clean it
The grass is too high and too thick.
Landroid®is shaking heavily.
Check the Blade Disc and blades, remove
debris and foreign objects from the blades
and Blade Disc.
The battery may be exhausted or old. Replace battery.
Landroid®is not operating at the
correct time.
The clock is not set to the correct time. Set the clock to the correct time by removing
and installing the battery pack.
Programmed cutting times for
Landroid®are not correct.
Change the time settings for the mower to
start and stop.
Landroid®is manually docked in the
charging base. Press START and then OK.
Landroid®cannot correctly dock
with the Charging Base
Environmental influences Restart Landroid®.
Poor connection caused by debris on
the Charging Strip.
Clean the Contact Pins located on the
Charging Base and the Charging Strip on
Landroid®using a cloth.
The Green light on the Charging
Base turns ON before charging is
complete.
The charging base is overheating, the
battery indication light flashes red.
Place the charging base in a shady area or
wait until the temperature has cooled down.

Owner’s Manual of Lawn Mowing Robot EN
19
Landroid®runs outside the
boundary wire. Landroid®does
not mow an area within a
boundary wire zone. Landroid®
reverses or rotates erratically
near the boundary wire.
The boundary wire of another Landroid®
or another robotic mower is positioned
too closely.
Ensure your Landroid®Boundary Wire has at
least 1m of space between the neighboring
boundary wire.
The boundary wire has been installed
with tight corners.
Check the boundary wire to ensure the
corners are smooth.
In wet conditions, the boundary wire
electric signal may leak where wire has
been joined or repaired.
Check boundary wire joints. Insulate to
provide a fully waterproof connection.
There is boundary wire electric signal
leakage due to broken insulation.
Repair damaged boundary wire insulation
with connectors.
The cutting area is larger than the
allowable cutting area for Landroid®.Contact service agent.
Landroid®wheels skid or damage
lawn.
Foreign obstacles, such as twigs
and branches may be lodged under
Landroid®.
Remove foreign objects from underside of
Landroid®.
The lawn is too wet. Wait until lawn has dried.
Landroid®exits the boundary
wire due to high speed when
going down a hill.
The Boundary Wire is placed on a slope
steeper than 17% (10°).
Reposition the Boundary Wire away from
slopes that are steeper than 17% (10°).
Please refer installation manual for details.
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.

Copyright © 2018, Positec. All Rights Reserved.