wurth Master PM 200-E User manual

702 451 X BA 0007
Bedienungsanleitung
Operating Instructions
Notice d’utilisation
Instrucciones para el manejo
Instruções de utilização
Istruzioni d‘uso
Gebruiksaanwijzing
Betjeningsvejledning
Bruksanvisning
Bruksanvisning
Käyttöohje
√‰ËÁ›Â˜ ¯ÂÈÚÈÛÌÔ‡
Kullanım kılavuzu
Poliermaschine PM 200-E
Polisher PM 200-E
Ponceuse PM 200-E
Pulidora PM 200-E
Máquina para polir PM 200-E
Lucidatrice PM 200-E
Polijstmachine PM 200-E
Poleremaskine PM 200-E
Polermaskin PM 200-E
Polermaskin PM 200-E
Kiillotuskone PM 200-E
™ÙÈÏ‚ˆÙ‹Ú·˜ PM 200-E
Polisaj makinesi PM 200-E
PM 200-E
Art.-Nr.
702 451 X
PM 200 E - Titel/Inhalt Seite 1 Montag, 10. Juli 2000 9:35 09

PM 200-E
Art.-Nr.
702 451 X
702 451 X BA 0007
9
8
7
5
6
1
PM 200-E
Art.-Nr.
702 451 X
2
4
3
PM 200 E - Bildseite Seite 3 Freitag, 7. Juli 2000 12:36 12

7
702 451 X BA 0007
1 Spindle lock
2 On/Off switch
3 Auxiliary handle
4 Spindle thread
5 Speed selector thumbwheel
6 Ventilation slots
Not all of the accessories illustrated or described are included
as standard delivery.
Polisher PM 200-E
Article number 702 451 X
Input power 1 200 W
Output power 750 W
No-load speed 900 - 2 700 min
–1
Backup pad/disc -Ø max. 200 mm
Spindle thread size M 14
Weight approx. 2,3 kg
Safety class / II
Tool Specifications Operating Controls
Working safely with this machine is
possible only when the operating
and safety information are read
completely and the instructions con-
tained therein are strictly followed.
In addition, the general safety in-
structions in the enclosed booklet
must be followed.
If the cable is damaged or cut through
while working, do not touch the cable
but immediately pull the mains plug.
Never use the machine with a dam-
aged cable.
Wear protective goggles, ear protec-
tors and face mask.
Wear protective gloves and sturdy
shoes. When necessary, also wear an
apron.
When working with the machine, al-
ways hold it firmly with both hands
and provide for a secure stance.
❑Always direct the cable to the rear away from the
machine.
❑Insert the mains plug only when the machine is
switched off.
❑Clamp the workpiece in case it does not remain
stationary from its own weight.
❑Connect machines that are used in the open via a
residual current circuit breaker with a triggering
current of 30 mA maximum. Use only extension
cables that are intended for outdoor use and are
protected against splash water.
❑For all work with the machine, the auxiliary han-
dle 3 must be mounted.
❑Protect tool insert from shock, impact and grease.
❑Only use tool inserts designed to run at speeds,
that at least match the no-load speed of the power
tool.
❑Observe the manufacturers instructions for assem-
bly and application of tool inserts.
❑Check tool inserts prior to use. The tool insert must
be assembled properly and rotate freely. Carry out
a no-load test run for at least 30 seconds. Do not
use damaged, out-of-center or vibrating tool in-
serts.
❑Do not work with materials containing asbestos.
❑Keep hands away from rotating tool inserts.
❑When grinding metal, flying sparks are produced.
Take care that no persons are endangered. Be-
cause of the danger of fire, no combustible mate-
rials should be located in the vicinity (spark flight
zone).
❑Pay attention to the direction of rotation. Always
hold the machine so that sparks and grinding dust
fly away from the body.
❑Do not clamp the machine in a vice.
❑Apply the machine to the workpiece only when
switched on.
❑Always switch off the machine and allow to come
to a stop before putting down.
❑For the labelling of the machine, do not drill into
the housing or attach with rivets. The protective in-
sulation is then no longer ensured. Use stickers.
❑Use only original Würth parts and accessories.
For Your Safety
GB
☞ For further notes on safety refer to enclosed Sheet
PM 200 E - GB Seite 7 Freitag, 7. Juli 2000 12:41 12

8
702 451 X BA 0007
The power tool is designed for polishing, smoothing,
sanding and brushing of metals and painted surfaces.
For damage caused by usage other then intended, the
user is responsible.
Mounting the Protective Devices
❑ Before any work on the machine itself, pull the
mains plug.
Auxiliary Handle 3
The machine may be operated only with the auxiliary
handle 3 mounted. Firmly screw in the auxiliary han-
dle 3 on the right or left of the machine head depending
on the working to be performed (Fig. A ).
Mounting tools (accessories) directly
To fasten tools with M 14 thread, press and hold spindle
lock 1 and screw the accessory on the spindle thread.
☞
Only depress spindle lock 1 , when polisher is at
standstill.
Mounting tools (accessories) with wheel
mandrel
Tools with center bore are mounted with wheel man-
drel 7 . Press and hold spindle lock 1 , mount wheel
mandrel 7 and tighten using open-end metric wrench,
size 19 or 20. Place wheel 8 and tool on mandrel. Start
flanged nut 9 and tighten using face spanner.
☞
Only depress spindle lock 1 , when polisher is at
standstill.
Always use the correct supply voltage: The power sup-
ply voltage must match the information quoted on the
tool identification plate. Tools with a rating of 230 V
can also be connected to a 220 V supply.
Switching On/Off
Switching on: Slide on/off switch 2 forwards, until it
locks.
Switching off: Depress the rear of the on/off switch 2 ;
the switch pops back into the off posi-
tion.
Soft Start
As a result of soft starting of the machine, a 16-A fuse
in the power circuit is adequate.
Restarting Protection
This function prevents uncontrolled restarting after a
power failure or when the mains plug was pulled. To put
back into operation, switch off with the on/off switch 2
and back on again.
Pre-set the required speed with speed-dial 5 in accord-
ance with the speed chart (reference values):
Use as intended
Before Use
Initial Operation
Speed-dial
setting 5 123456
rpm 900 1500 2000 2200 2500 2700
Job Application Speed-
dial
setting 5
Finish
brushing Nylon cup brush, for finish brushing of wood or coarse
sanding of paint, prior to a
new coating
5 - 6
Finish
sanding Terry cloth, fastened on a backup pad, for finish sanding
of metal surfaces
5 - 6
Smoothing Flap disc, to even out slight
irregularities on metal surfaces 3 - 4
Polishing Polishing ring, polishing disc,
lamb´s wool bonnets, polishing
buffs, flap discs, cotton or terry
cloth buffs, for polishing metal,
stone and plastics.
1 - 4
Speed Selection
PM 200 E - GB Seite 8 Freitag, 7. Juli 2000 12:41 12

9
702 451 X BA 0007
❑ Clamp the workpiece in case it does not remain sta-
tionary from its own weight.
❑ Do not load the machine so heavily that it comes to
a standstill.
Apply pressure on the polisher evenly and guide back
and forth across the surface, to avoid overheating of the
workpiece surface.
❑ Before any work on the machine itself, pull the
mains plug.
☞
Always keep the machine and the ventilation
slots clean. Blow out the motor regularly with dry
compressed air.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be car-
ried out by an authorised customer services agent for
Würth power tools.
In all correspondence and spare parts orders, please al-
ways include the 7-digit order number given on the
nameplate of the machine.
Recycle raw materials instead of dis-
posing as waste.
Machine, accessories and packaging
should be sorted for environment-friend-
ly recycling.
The plastic components are labelled for categorized re-
cycling.
For this Würth machine, we provide a 12 -month guar-
antee against material and workmanship defects from
the date of purchase (verified by invoice or delivery
document). Damage that has occurred will be corrected
by replacement or repair.
Damage caused by normal wear, overloading or im-
proper handling is excluded from the guarantee.
Claims can only be accepted if the device is sent without
having been disassembled, to a Würth branch office,
your Würth sales representative or a customer service
agent for Würth power tools.
Measured values determined according to EN 50 144.
The A-weighted noise levels of the tool are typically:
Sound pressure level: 87 dB (A).
Sound power level: 100 dB (A).
Wear ear protectors!
The weighted acceleration is typically 4,0 m/s
2
.
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 50 144, EN 55 014,
EN 61 000 according to the provisions of the regula-
tions 98/37/EC, 89/336/EEC, 73/23/EEC.
00
Adolf Würth GmbH & Co. KG
Karl Weidner ppa. Otto Steck
Operating Instructions
Maintenance and Cleaning
Environmental Protection
Guarantee
Noise/Vibration Information
Declaration of Conformity
Subject to change without notice
PM 200 E - GB Seite 9 Freitag, 7. Juli 2000 12:41 12