WYLER wylerCONNECT User manual

wylerCONNECT
Quick Reference
Release 1.1.1
Seite 1 / 2
WYLER AG Phone [phone] e-mail:[e-mail] www.wylerag.com
Im Hölderli 13
8405 Winterthur Outside Switzerland: contact our representatives
Switzerland www.wylerag.com/en/contact/representatives/
Thank you for choosing WYLER!
Read this quick reference before start working with wylerCONNECT
Please observe the safety instructions.
Brand and Type
Brand wylerCONNECT, Types Art. 029-0001-002 with plastic box
Art. 029-0001-001 device only
Warning! The following sign is used in this Quick Reference:
This is intended to indicate special dangers
Safety instructions
The wylerCONNECT complies with the applicable directives and standards, see:
This Quick Reference - The nameplate on the back of the device
DOC Declaration of Conformity at www.wylerag.com
WARNING
Intended Use
The wylerCONNECT is designed exclusively to connect measuring devices with PCs or Laptops by cable or
by Bluetooth ®.
Operation System: WINDOWS 10
Attention!: There is no other use!
Not intended use
- Do not immerse underwater! Since the device may suffer a short circuit inside.
- Do not use as a hammer! The damaged measuring surfaces are then no more precise.
- Do not throw the device! The housing can cause serious injury.
WARNING
- Do not use this device near sources of strong electromagnetic energy Radiation (e.g.,
unshielded radio frequency source) because they can interfere with operation.
- Do not immerse the device in water or other liquids! The IP6x
standarddoes not cover underwater situation.
Technical data, Mass, Weight, Protection, Operation, Storage
Power supply:
5V, USB-C
Power consumption:
Max 500mA/5V
Dimension L x H x D:
64 x 41 x 70 mm
Weight:
170 g
Protection:
IP6x
Weight Scope of delivery:
550 g
Storage:
In storage case: -20°.. +60° C
Operation temperature:
0°… 40 °
Scope of delivery 029-0001-001 (accessories see www.wylerag.com)
1. Case for storage, transport and shipping for repair
2. wylerCONNECT
 USB Cable –A/-C
4. wylerTRIGGER
This Quick reference.
Decommissioning, disposal
When decommissioning the Clinotronic S,follow the local regulations for
Disposal of electronic waste.
- The batteries must be removed from the device and both parts separately from
the be supplied for proper disposal.
WARNING

wylerCONNECT
Quick Reference
Release 1.1.1
Seite 2 / 2
Control Elements, LED‘s
1 Housing
2-4 LED red,green, blue
5 USB-C
6 RS 485
7 Trigger at wylerTRIGGER
Connection with PC/LAPTOP
Connect with USB -C/-A cable The green LED (3) shows
operational readiness.
LED Signal Code (red, green, blue)
Intention
Cause
permanent
Blink
0.5 Hz
blinking
fast 1 Hz
Final state
Use device
Connect via USB
green
green permanent
Device searches via cable
Via software
green
green fast blinking
Device searches via radio
Via software
blue
blue fast blinking
Device searches via radio & cable
blue/green
Fast blinking
blue+green
Device connected via cable
Via software
green
green blinking
Device connected via radio
Via software
blue
blue blinking
Device connected via radio & cable
blue/green
blinking
blue+green
Trigger detected
Teaching of trigger
red
1 flash
Overcurrent
red
red blinking
Malfunction
red
red permanent
List of Bluetooth® compatible devices: (a maximum of 7 devices
simultaneously connectable depending on harmful interference in environment)
→ BlueLEVEL, BlueLEVEL-2D, BlueCLINO 10°/60°, BlueCLINO, HP, Clinotronic S
List of incompatible radio devices:
→ BlueMETER, BlueTC, BlueMETER SIGMA, LEVELMETER 2000
List of RS485 compatible devices
allways connected with MultiTC, also in mixed operation, if required with 24V power supply:
→ ZEROTRONIC 3 and C, ZEROMATIC 2/2 and 2/1, Clinotronic PLUS, MINILEVEL NT
List of RS485 compatible devices
if required connected with MultiTC, also in mixed operation, if required with 24V power supply:
→ BlueLEVEL(Basic), BlueLEVEL-2D, BlueCLINO 10°/60°, BlueCLINO, HP, BlueMETER SIGMA, BlueTC
List of RS485 compatible devices with special cable
→ LEVELMETER 2000 with radio, Clino2000
List of RS485 incompatible devices: Transceiver/*Converter (TC, silver)
For more information read the manual at www.wylerag.com
5
6
How to teach the wylerTrigger:
Keep the wylerTRIGGER near to wylerCONNECT.
Press the red button at least 5seconds.
Red (2) LED of wylerCONNECT will
Blink one time.
Trigger is teached know.
wylerTRIGGER
4
2
3
1
5
6