Xerox WorkCentre 7132 User manual

Xerox WorkCentre®7132
Copyright © 2006, Xerox Corporation. All rights reserved.
1
Quick Scan Features
Setup Guide
This guide includes instructions for:
Scan to Email on page 1
Scan to Mailbox Setup (Optional) on page 5
Network Scanning Setup (Optional) on page 7
Scan to FTP/SMB (Optional) on page 9
Scan to Email
Hard copies can be scanned at the device and sent to remote clients as email attachments in
Single TIFF, Multi TIFF, PDF, and JPEG format. SMTP and POP3 mail servers are used to
send and receive email respectively.
See also:
System Administrator Guide: Contains detail about email setup.
User Guide: Contains information on how to send an email and how different addresses
are used (Local Address vs. Global Address - LDAP).
Install the Scan to Email Option on the WorkCentre
1. Power on the device.
2. Press Login/Logout, then type the UserID 11111 and press Confirm.
3. From the System Administrator menu, select System Settings.
4. Select System Settings.
5. Select Common Settings.
6. Select Maintenance/Diagnostics.
7. Select Software Options.
8. Press Keyboard. Type the Email license key code.
9. Select Reboot.
10. Proceed with the Prerequisites for Scan to Email Setup on page 2.
701P45042

Scan to Email
Copyright © 2006, Xerox Corporation. All rights reserved.
2
Prerequisites for Scan to Email Setup
Confirm that:
1. An existing operational network using TCP/IP is available.
2. The device must be setup with DNS and the Domain Name settings for the network.
have been correctly setup for the multifunction device.
* Only if the SMTP server requires login and password for authentication.
Procedure for Scan to Email Setup
1. Enable the Scan to Email option using the instructions in Install the Scan to Email
Option on the WorkCentre on page 1.
2. Press Login/Logout, then type the UserID 11111 and press Confirm.
3. From the System Administrator menu, select System Settings.
4. Select System Settings.
5. Select Network Settings.
6. Select Port Settings.
7. Enable the Receive Email port and Send Email port by highlighting each port and
selecting Change Settings.
8. Select Close several times then Exit. The device will reboot.
9. From a workstation, open up a web browser (such as Internet Explorer), and then enter
the IP address in the format http://xxx.xxx.xxx.xxx (the xxx's represent the device IP
address). If connected properly, you should see a CentreWare Internet Services web
page for your device.
Data to Setup Email Install Requirement Comments
SMTP mail server Host
Name or IP address Required If using an external mail server,yourInternetService
Provider will provide you
with the mail server name or
IP address.
SMTP login/password Required*
WorkCentre Email address Required This email address will fill in
the "From" field on the
emails sent from the device.
Local email addresses Optional A Local Address Book can
be created to store email
addresses.
LDAP server address can
be enabled LDAP Host Name Displays only email addresses on the corporate
(LDAP) internal address
book.

Scan to Email
Copyright © 2006, Xerox Corporation. All rights reserved.
3
10. Set up the SMTP server configuration via CentreWare Internet Services:
a. Click the Properties tab.
b. Click the Protocols Settings folder.
c. Click SMTP.
d. Enter the SMTP mail server host name or IP address and port number (the default
is port 25).
e. Select an authentication type, if required by the SMTP server.
f. Enter a User name and Password to be used for authentication, if required.
g. Click on Apply New Settings.
h. Enter the user name of 11111 and the password of x-admin if prompted for a User
name and Password.
i. Ignore the screen to reboot the machine.
11. Set up the Machine Email address via CentreWare Internet Services:
a. Click the Properties tab.
b. Click on Machine Details.
c. Enter the information for the Machine Email Address.
d. Click on Apply New Settings.
e. Click on Reboot Machine.
12. From the device, load a sample document that you want to email into the document
feeder.
13. Press the All Services button.
14. Press the Email button.
15. Press the Keyboard button to type an email address using the keypad.
16. Press the Start button.
17. Verify that the recipient(s) received the email with the document attached.

Scan to Email
Copyright © 2006, Xerox Corporation. All rights reserved.
4
Scan to Email Troubleshooting
For internal corporate mail servers, substitute the word "Corporate" for "ISP" in the
following troubleshooting table.
Symptom Possible Cause Resolution/Validation
SMTP error at
multifunction device
Incorrect Mail Server or
Host Name Validate that the correct ISP mail server name has been entered in
the SMTP Host Name field.
Incorrect settings in
Microsoft Outlook Express Verify that you can access the ISP mail server from within Microsoft
Outlook Express and that all
settings are correct.
Incorrect multifunction
device email address
entered
Verify that the device is using the
correct email address in the From:
field. The Email address must
match what the ISP's mail server is
expecting.
ISP requires SMTP
authentication to their mail
server
Check with your ISP to determine
if this is a requirement. If so,
enable SMTP authentication for
the multifunction device via
CentreWare Internet Services.
ISP does not allow mail on
the standard port number
25
Check with your ISP to determine
if this is the problem. Ask if they
can accept mail on another port
number. If so, change the SMTP
port number for the multifunction
device via CentreWare Internet
Services.
ISP requires login to the
email account via Microsoft
Outlook Express before
allowing mail to be sent
Check with your ISP to determine
if this is a requirement. If so, login
to the Microsoft Outlook Express
account, and then try sending the
email. If this is successful, you can
set Outlook Express to check
email every 5 or 10 minutes for the
multifunction device's email
account.

Scan to Mailbox Setup (Optional)
Copyright © 2006, Xerox Corporation. All rights reserved.
5
Scan to Mailbox Setup (Optional)
This feature allows documents to be stored in a mailbox for future processing. Scan to
Mailbox can be setup at the machine control panel or at a network computer through the
CentreWare Internet Services webpage. Instructions for each method are shown.
See also:
System Administrator Guide: Contains detail concerning Network Scanning setup.
User Guide: Contains information on mailbox setup through the control panel, as well
as CentreWare Internet Services.
Prerequisites for Scan to Mailbox Setup
Confirm that:
1. An existing operational network utilizing TCP/IP is available.
Procedure for Scan to Mailbox Setup through the Control Panel
1. Power on the device.
2. Press Login/Logout, then type the UserID 11111 and press Confirm.
3. From the System Administrator menu, select System Settings.
4. Select Setup Menu.
5. Select Mailbox.
6. Select a mailbox to configure and press Create/Delete.
7. Select password options and type a password, if desired. If a password is entered for a
mailbox, no one else can access that mailbox before entering the password.
8. Select Mailbox Name and press Change Settings.
9. Type a name for the mailbox and press Save.
10. Change other settings as desired. When finished, select Close several times then Exit.
Procedure for Scan to Mailbox Setup through CentreWare Internet Services
1. From a workstation, open up a web browser (such as Internet Explorer), and then enter
the device's IP address in the format http://xxx.xxx.xxx.xxx (the xxx's represent the
device's IP address). If connected properly, you should see a CentreWare Internet
Services web page for your device.
2. Create mailboxes:
a. Click the Properties tab.
b. Click the Mailboxes folder.
c. Click the Edit button.
d. Enter the appropriate information. If a password is entered for a mailbox, no one
else can access that mailbox before entering the password.
e. Click on Apply New Settings.
Note
If prompted to enter a User Name and Password, the default settings are 11111
and x-admin respectively.

Scan to Mailbox Setup (Optional)
Copyright © 2006, Xerox Corporation. All rights reserved.
6
Procedure for Scanning to Mailbox
1. At the device, select All Services and Scan to Mailbox.
a. Select the mailbox number to which you want to scan a document.
b. Load the sample document into the document feeder.
c. Press the Start button.
2. Verify that the scanned document is in the mailbox.
a. Select the mailbox number to which the document was scanned.
b. Select Document List.
Note
To retrieve the scanned document to a Windows PC, install the scan driver on the
PC or use CentreWare Internet Services. More information can be found on the
CentreWare Utilities CD-ROM and the "CentreWare Internet Services" chapter of
the User Guide.

Network Scanning Setup (Optional)
Copyright © 2006, Xerox Corporation. All rights reserved.
7
Network Scanning Setup (Optional)
Network scanning uses FTP or SMB protocols to transfer scanned documents on to a server
or a client. Templates (scanned file properties) and repositories (destination folders) need to
be set up to enable network scanning.
See also:
User Guide: Contains information on how to set up templates and repositories.
System Administrator Guide: Contains details about Network Scanning setup.
Prerequisites for Network Scanning Setup
Confirm that:
1. An existing operational network utilizing TCP/IP is available.
2. A repository (folder) exists on the FTP or SMB server to hold the scanned documents.
A user account for the device must be created on the server that allows access to the
repository folder.
Procedures for Network Scanning Setup
1. Power on the device.
2. Press Login/Logout, then type the UserID 11111 and press Confirm.
3. From the System Administrator menu, select System Settings.
4. Select System Settings.
5. Select Network Settings.
6. Select Port Settings.
7. Enable the following ports by highlighting each port and select Change Settings.
a. Internet Services (HTTP).
b. FTP Client Port or SMB Port (depending on which protocol is used).
c. SNMP Port.
d. SOAP Port.
8. Select Close several times then Exit. The device will reboot.
9. From a workstation, open up a web browser (such as Internet Explorer), and then enter
the device's IP address in the format http://xxx.xxx.xxx.xxx (the xxx's represent the
device's IP address). If connected properly, you should see a CentreWare Internet
Services web page for your device.
10. Create a Repository setting.
a. Select the Print/Scan Services tab.
b. Select Job Templates.
c. Select the Display Job Template Screen button.
d. Select File Repository Setup.
e. Enter the appropriate information to name this repository setting and provide a
path to the repository folder previously created on the FTP or SMB server. The
Port setting can be left blank. (For Anonymous FTP, a value must be entered in
the password field).

Network Scanning Setup (Optional)
Copyright © 2006, Xerox Corporation. All rights reserved.
8
f. Select Apply.
Note
If prompted to enter a User Name and Password, the default settings are 11111
and x-admin respectively.
11. Create a Template.
a. Select the Template button.
b. Select Create New.
c. Enter a name for the template.
d. Select Public for the Repository Type. The repository created above should
appear in the window.
Note
A private template does not require separate repository settings, since the routing
information is entered directly into the template itself.
e. Select Next.
f. Make selections as needed to define the properties of the scanned files created by
this template.
g. Select OK.
Procedure for Network Scanning
1. At the device select All Services and Network Scanning.
2. Select a template from the list. You can also change any other value from the control
panel without impacting the template configuration; only the current job will be
affected.
3. Load a sample document into the document feeder.
4. Press the green Start button. The job is sent to the server using FTP or SMB protocol
as defined within the template.
5. From a workstation, log on to the FTP or SMB Server. Navigate to the repository
(destination) that was specified earlier. Your scanned document is located in that folder.
Note
If remote authentication has been enabled, a separate login screen appears when
the Network Scanning feature is selected. Documents are not scanned unless the
remote authentication server authenticates user access.

Scan to FTP/SMB (Optional)
Copyright © 2006, Xerox Corporation. All rights reserved.
9
Scan to FTP/SMB (Optional)
Files can be scanned on the multifunction device and routed to a server or a client using FTP
or SMB protocols. Directory structures (repositories) need to be created on the server to hold
the scanned documents.
See also:
System Administrator Guide: Contains more detail concerning Scan to FTP/SMB setup.
User Guide: Contains information on how to set up templates and repositories.
Prerequisites for Scan to FTP/SMB
Confirm that:
1. An existing operational network utilizing TCP/IP is available.
2. FTP/SMB Server/Client exists and is running.
3. A repository (folder) exists on the FTP/SMB server to hold the scanned document. A
User account for the device must be created on the server that allows access to the
repository folder.
Procedure for Scan to FTP/SMB
1. Power on the device.
2. Press Login/Logout, then type the UserID 11111 and press Confirm.
3. From the System Administrator menu, select System Settings.
4. Select System Settings.
5. Select Network Settings.
6. Select Port Settings.
7. Enable the following ports by highlighting each port and select Change Settings.
a. Internet Services (HTTP).
b. FTP Client Port or SMB Port (depending on which protocol is used).
c. SNMP Port.
d. SOAP Port.
8. Select Close several times then Exit. The device will reboot.
9. Select All Services.
10. On the touch screen, select Scan To FTP/SMB.
11. Select the FTP button.
12. Select the desired protocol for this scan and select Save.
13. Enter all the information required. See the User Guide for more detailed information.
Select any field to access a keyboard for data entry. Select Save after each complete
entry.
14. Load a sample document into the document feeder.
15. Press the Start button.

Scan to FTP/SMB (Optional)
Copyright © 2006, Xerox Corporation. All rights reserved.
10
16. From a workstation, logon to the FTP/SMB server. Navigate to the directory path
(repository) that was set up earlier on the server. Your scanned document can be found
in the specified directory.
Note
If remote authentication has been enabled, a separate login screen appears when
the Scan to FTP/SMB feature is selected. Documents are not scanned in unless the
remote authentication server authenticates user access.