Xerox WorkCentre M118i User manual

Xerox WorkCentre®M118i
Copyright © 2004 Xerox Corporation. All rights reserved.
1
This guide provides a quick reference for setting up the Scan to E-mail feature on the
Xerox WorkCentre M118i. It includes procedures for:
■Enabling Scan to E-mail on page 3
■Configuring Scan to E-mail on page 3
■Verifying Scan to E-mail Setup on page 5
■Troubleshooting Scan to E-mail on page 5
S
ee a
l
so:
System Administrator Guide: Provides detailed information about setting up E-mail.
User Guide: Provides step-by-step instructions for sending E-mail.
Scan to E-mail
Quick Setup Guide
701P42574

XeroxWorkCentreM118i
2
Before You Begin
Before enabling and configuring Scan to E-mail:
■Verify that the machine is connected on a TCP/IP network. See the Network Connection Quick
Setup Guide for more information.
■Obtain the following information from your network administrator or Internet Service Provider (ISP):
Required:
Administrator E-mail Address
NoteNoteNote
Enter the e-mail address created for the M118i machine
in the Administrator E-Mail Address field. The email
address populates the From portion of each e-mail sent
from the M118i machine. If an email address for the
machine has not been created, enter your email
address. When an email address is created for the
machine, replace your e-mail address with the
machine’s e-mail address. See Configuring Scan to
E-mail on page 3.
____________________________________
SMTP Server Address ________ . ________ . ________ . ________
Local E-mail Address for testing ____________________________________
Optional:
DNS Server Address ________ . ________ . ________ . ________
POP3 Server Address ________ . ________ . ________ . ________
POP3 Login User Name:
__________________________________
Password:
___________________________________

Enabling Scan to E-mail
XeroxWorkCentreM118i
3
Enabling Scan to E-mail
To enable the Scan to E-mail feature:
1. On the control panel, press the Log In/Out button.
2. Press the Select button below the display to select System Settings.
a. Use the numeric keypad to enter the Password. The default password is 11111.
b. Press the Select button to select Confirm.
3. Select Print Settings,and then press the Enter button.
4. Press the Select button until you see Software Option on the display, and then press the Enter button.
5. Use the numeric keypad to enter the Software Option password for Scan to E-mail, and then press the
Enter button. The password can be found on the inside cover of the Scan to E-mail Instructions.
Configuring Scan to E-mail
After Scan to E-mail is enabled, follow these steps to configure Scan to E-mail on your network.
Set the Administrator E-mail Address
1. At your computer, launch your web browser.
2. Enter the machine’s IP address in the browser’s Address field (http://xxx.xxx.xxx.xxx).
3. Click the Properties tab.
4. Select Machine Details on the left sidebar.
a. Enter the machine’s email address in the Administrator E-mail Address field. If an email address for
the machine has not been created, enter your email address. Once an email address is available for the
M118i machine, repeat Steps 1 through 5 in this procedure to replace your e-mail address with the
machine’s email address.
b. Click the Apply New Settings button at the bottom of the page.
c. Enter the CentreWare IS administrator’s User Name and Password, and then click the OK button.
Note
The default CentreWare IS administrator’s User Name is admin and Password is x-admin. These
should be changed after network setup is complete.
d. At the reboot prompt, click the Reboot button.
5. Wait one minute for the reboot to complete, and then click the browser Refresh button.

Configuring Scan to E-mail
XeroxWorkCentreM118i
4
Enable the E-mail Ports
1. Click the Properties tab.
2. Select Port Status on the left sidebar.
a. Enable the SNMP, Send E-mail, and Mail Notice Service ports. Do not modify the other port settings
on this page.
b. Click the Apply New Settings button at the bottom of the page.
c. At the reboot prompt, click the Reboot button.
3. Wait one minute for the reboot to complete, and then click the browser Refresh button.
Enter the SMTP Settings
1. Click the Properties tab.
2. Select the Protocol Settings folder on the left sidebar, and then select E-mail.
a. Enter the SMTP Server Address.
b. If SMTP authentication is required, enter the POP3 Server Address, POP User Name, and
POP Password.
Note
The POP3 Server Address can be entered as an IP address or a server name.
c. If the machine uses a host name rather than an IP address, click TCP/IP in the left side bar, and verify
that the DNS Address 1 field contains the DNS Server Address. For more information, see the
Network Connection Quick Setup Guide.
d. Click the Apply New Settings button at the bottom of the page.
e. At the reboot prompt, click the Reboot button.
3. Wait one minute for the reboot to complete, and then click the browser Refresh button.
Create an Address Book Entry to Use for Verifying Scan to E-mail Setup
1. Click the Properties tab.
2. Select Address Book on the left sidebar.
a. Type a Speed Dial number from 1–200 to assign to the test recipient, and then click the Edit button.
b. Select E-mail from the Address Type drop-down list.
c. Enter the recipient’s local E-mail address in the Recipient Address field.
d. Enter the Recipient Name.
e. Click the Apply New Settings button.

Verifying Scan to E-mail Setup
XeroxWorkCentreM118i
5
Verifying Scan to E-mail Setup
Send a test E-mail to verify the Scan to E-mail setup:
1. Load a sample document into the document feeder.
2. On the control panel, press the E-mail button.
3. Press the Address Book button.
4. In the menu, highlight the address book entry you created, and then press the Next Address button to
select it.
5. Press the Enter button.
6. Press the green Start button to scan the document and send it as an attachment to the selected recipient.
7. Verify that the recipient received the E-mail with the scanned document as an attachment.
Troubleshooting Scan to E-mail
If the machine reports an SMTP error, use the following table to determine the cause and resolution:
Possible Cause Resolution
Incorrect mail server host name ■Verify that the correct corporate or ISP mail server name has been entered in
the SMTP Host Name field.
■Ensure that DNS information is entered correctly.
Incorrect “From:” E-mail address
entered
Verify that the Administrator E-mail Address is correct. The E-mail address must
match what the corporate or ISP mail server is expecting.
The corporate or ISP mail server
requires authentication
Check with your network administrator or ISP to determine if the mail server
requires authentication. If so, use CentreWare IS to enable “POP before SMTP”
authentication, and then enter the POP User Name and POP Password
information.
The corporate or ISP mail server
does not allow mail on the
standard port number 25
Check with your network administrator or ISP to verify that Port 25 is being used for
mail service. If not, obtain the mail service port information, and then use
CentreWare IS to configure it.