Xerox Phase 6200 Technical specifications

Phaser®6200 Color Laser Printer
Copyright © 2002 Xerox Corporation. All Rights Reserved. 14
Regular Printer Maintenance
Your printer needs little maintenance other than periodic cleaning of the density sensor and replacing
the following Customer-Replaceable Consumables (CRCs) and Customer-Replaceable Units (CRUs):
■Toner cartridges (black, cyan, magenta and yellow) —see page 17
■Imaging unit —see page 18
■Transfer roller —seepage 23
■Fuser —see page 20
■Feed rollers —see page 25
Order extra printer supplies when the printer’s front panel displays a warning that the consumable is
low or near the end of its life. You must replace the consumable when the front panel displays an error
message that the consumable is empty or at the end of its life. For part number information, refer to the
Supplies section of the Support Guide on the Interactive Documentation CD-ROM. To order
consumables and other supplies, visit the Phaser®6200 Supplies and Accessories web site. Each item
includes installation instructions in the package.
Caution
Keep the imaging unit out of direct sunlight. Otherwise, faded images, light areas or dark
bands may result. Do not place the printer near vents or dust-producing equipment.
Warning
Do not burn the old toner cartridges, the imaging unit, the transfer roller, or the fuser.
Cleaning the outside of the printer
You can clean the outside of the printer with a soft, damp well-wrung cloth. You can use a cloth
moistened with a mild neutral detergent to remove stains; do not spray detergent directly onto the
printer.
Warning
To prevent electric shock, turn the printer off and unplug the power cord before cleaning the
printer.
Caution
Do not use a vacuum cleaner to clean the printer. Do not lubricate the printer with oil.

Regular Printer Maintenance
Phaser®6200 Color Laser Printer 15
Cleaning the density sensor
The printer stops printing when the density sensor is dirty. To clean the density sensor:
1. Use the latch on the front of the printer to open Front Door A.
2. Remove the transfer roller. Squeeze the orange tabs at both sides of the transfer roller and gently
lift it out of the printer.
3. Use a dry towel or cotton swab to wipe the density sensor.
6200-66
6200-23
6200-12

Regular Printer Maintenance
Phaser®6200 Color Laser Printer 16
Caution
Do not use canned air or isopropyl alcohol on the sensor.
4. Reinstall the transfer roller. Insert the rounded ends of the transfer roller into the curved black
guides inside the printer. Lock the transfer roller into the printer by pushing down on the orange
tabs until you hear a click.
5. Close the front door.
6200-24
6200-25
6200-64

Replacing a Toner Cartridge
Phaser®6200 Color Laser Printer 17
Replacing a Toner Cartridge
6-8x
12
4.2
2.1
4.1
2.2
4
Click
Declic
Clic
Klicken
Clic
Clique
Klik
Klick
6
Pull
Tirer
Tirare
Ziehen
Tirar
Puxe
Trek
Dra
5
3

Replacing the Imaging Unit
Phaser®6200 Color Laser Printer 18
Replacing the Imaging Unit
12
12
4
8
4x
7
Pull
Tirer
Tirare
Ziehen
Tirar
Puxe
Trek
Dra
6
4.5 kg
10 lbs
3
PHASER
®
6200
Imprimante couleur laser
Uniteimageurcouleur
PHASER
®
6200
ColorLaser Printer
12
ColorImaging Unit
5

Replacing the Imaging Unit
Phaser®6200 Color Laser Printer 19
9
12 13
8
11
10
4.5 kg
10 lbs

Replacing the Fuser
Phaser®6200 Color Laser Printer 20
Replacing the Fuser
6
2
7
1
34
5

Replacing the Fuser
Phaser®6200 Color Laser Printer 21
8
10
11 12
9
7

Replacing the Fuser
Phaser®6200 Color Laser Printer 22
12 13
14

Replacing the Transfer Roller
Phaser®6200 Color Laser Printer 23
Replacing the Transfer Roller
3.13.1
3.2
3.3
12
3
4 5