xG Technology CN3200 Operator's manual

G7603 - Release 3.3

2
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
Product features and specifications are subject to change without prior notice.
xG® and xMax® are registered trademarks of xG Technology, Inc.
All other trademarks used herein are property of their respective owners.
For the latest product documentation and software
updates, please refer to our Web site at
www.xGTechnology.com/support
xG Technology, Inc.
240 South Pineapple Avenue, Suite 701
Sarasota, FL 34236
[phone]
www.xGTechnology.com

3
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
Table of Contents
Introduction ...............................................................................................................7
About this Product....................................................................................................................7
About this Book ........................................................................................................................7
Before You Begin ......................................................................................................................7
Hardware Overview....................................................................................................8
Powering the CN3200 Modem .................................................................................................8
Connectors................................................................................................................................9
Status LED .................................................................................................................................9
Important Installation and Safety Notices.................................................................10
RF Exposure ............................................................................................................................10
FCC Compliance ......................................................................................................................11
Before Powering the CN3200 Dual Band Routing Modem.........................................12
Configuring the CN3200 Dual Band Routing Modem.................................................13
xMax Network Management .................................................................................................14
WiFi Network Management ...................................................................................................15
Connect to the WiFi Access Point.................................................................................................. 16
Antenna Considerations ...........................................................................................17
Antenna Configuration ...........................................................................................................18
Installation Preparation ............................................................................................19
Assemble Your Parts and Tools ..............................................................................................19
Equipment Provided in the Standard CN3200 Dual Band Routing Modem Kit .....................21
Installation Procedure Overview...............................................................................22
Antenna Cabling Identification...............................................................................................23
Antenna Orientation Overview ..............................................................................................24
Antenna Alignment ......................................................................................................................... 24
Antenna Azimuth............................................................................................................................. 24
Antenna Tilt ..................................................................................................................................... 24
Estimating Installation Times .................................................................................................25
Completion and Quality Control Check List ...........................................................................26
Installation Details....................................................................................................27
Antenna Installation and Adjustment Overview....................................................................27
Antenna Azimuth Adjustment......................................................................................................... 27
Mechanical Tilt Adjustment ............................................................................................................ 27
Installation Example ........................................................................................................................ 27
CN3200 Modem / xMax Panel Antenna Assembly ................................................................29
Mounting Bracket............................................................................................................................ 29

4
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
U-Bolts ............................................................................................................................................. 30
2.4 GHz Panel Antenna.................................................................................................................... 30
Installation Procedure ............................................................................................................31
Connecting the CN3200 Dual Band Routing Modem to the xMax Network ...............34
Wired Internet Connectivity and Setting Up a WiFi Hotspot......................................35
Wired Internet Connectivity...................................................................................................35
Technical Specifications ............................................................................................36
Warranty ..................................................................................................................37
Limited Warranty....................................................................................................................37
SCOPE OF THE WARRANTY.............................................................................................................. 37
ADDITIONAL PROVISIONS OF THE WARRANTY............................................................................... 38
OBTAINING SERVICE AND SUPPORT UNDER WARRANTY............................................................... 39
EXCLUSIVITY OF THE WARRANTY.................................................................................................... 39

5
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
List of Figures
Figure 1 —Antenna Configuration ........................................................................................................... 18
Figure 2 —CN3200 Dual Band Routing Modem Parts Checklist.............................................................. 19
Figure 3 —Installation Tool Kit Checklist ................................................................................................. 20

6
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
THIS PAGE INTENTIONALLY LEFT BLANK

7
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
The CN3200 Dual Band Routing Modem is an all-IP, high-capacity and high-performance wireless
access point. It is waterproof and made to handle wide temperature ranges. The CN3200 Modem is
designed for installation in fixed locations such as towers and buildings.
This manual provides basic instructions for installation and configuration of the CN3200 Modem. It
also describes how to connect to the xMax Network and then connect Internet-enabled wireless
devices to the xMax Network.
IMPORTANT
The CN3200 Modem is shipped with the parts needed for basic installation and operation. These
items are shown below. Be sure each of these items is included in your product package. If any item
is missing, please contact the place of purchase.
Depending upon the requirements of your installation, you will also need to purchase additional
components such as cables and surge protectors. A checklist of typically required parts is shown in
the Installation section.
xMax Panel Antenna
and Cables
2.4 GHz Panel Antenna
with Mounting Bracket
and Cable
PoE++ Power Supply
and AC Power Cord
Weatherproof
Ethernet Kit
Ferrite Beads (6)
Installation Bracket
and Hardware

8
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
The CN3200 Dual Band Routing Modem is a compact form-factor base station used for
communicating wirelessly with xMod Mobile Hotspots. The xMax CN3200 Modem is an all-IP, high-
capacity, high-performance wireless access point that that delivers wide-area coverage and
reliability, even when there is significant interference.
The CN3200 Modem is totally protected against dust and moisture.
The CN3200 Modem is a Power-over-Ethernet (PoE+) device. The IEEE 802.3at PoE+ standard
enables transmission of both data and the power to operate a device over a single Cat5e cable
connection.
The CN3200 Modem REQUIRES a PoE++ adaptor, as supplied.
The device will NOT operate with a low-power PoE switch or adaptor.
Both top Tx RF ports MUST be properly terminated
before power (PoE) is applied to the unit.
Applying power without proper RF port
termination might damage the unit
and void the product warranty.
Private
Network
110-240
VAC,
50-60 Hz
PoE++
Power Supply
CN3200
DATA OVER
ETHERNET
POWER
plus DATA
TERMINATE
BEFORE
POWER UP

9
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
The CN3200 Modem features seven connectors:
Four external xMax antenna connectors (N-type / female)
A connector for an external 2.4 GHz antenna (TNC-type / female)
A weatherproof Ethernet connector
An unused connector
TOP CONNECTORS
BOTTOM CONNECTORS
Tx 3
Tx 1
Tx/Rx 4
Unused Port
Ethernet
Tx/Rx 2
The CN3200 Modem Status LED indicates power, network status, and hardware fault conditions.
Under normal operating conditions, the LED glows GREEN.
2.4 GHz ANTENNA CONNECTOR
xMax Network
GREEN
SOLID
CONNECTED
RED
SOLID
NOT
CONNECTED
STATUS LED

10
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
These notices apply to the CN3200 Dual Band Routing Modem.
Be sure to read, understand and follow these instructions.
Heed all warnings.
Only use accessories and attachments specified by xG Technology.
Keep a copy of these instructions for future reference.
FCC Part 15 Requirement
The CN3200 Dual Band Routing Modem MUST only be installed by a professional installer. It is the
responsibility of the installer to adjust the transmit power level to ensure that the output power
plus antenna gain does not cause the device to exceed FCC Part 15 output power regulations.
Shielded and grounded Ethernet MUST be used to avoid damage to the CN3200 Modem unit
and ensure proper operation.
Lightning Protection MUST be used on all antenna connections and Ethernet tower runs.
Hazardous situation, which if not avoided,
could result in death or serious injury.
All antennas MUST either be located on the exterior of a vehicle or mounted on a pole.
Every antenna MUST be separated from users by more than 23 cm (0.75 ft) at all times.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of
23 cm (0.75 ft) between the radiator and your body. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
Changes or modifications to this device
not expressly approved by xG Technology
could void the user’s authority to operate the equipment
and void the product warranty.

11
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio technician for help.

12
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
Both top Tx RF ports, MUST be properly terminated
before power (PoE) is applied to the unit.
Applying power without proper RF port
termination might damage the unit
and void the product warranty.
TERMINATE
BEFORE
POWER UP
ETHERNET

13
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
These steps set up the CN3200 Dual Band Routing Modem for use. After completing these
configuration steps, the CN3200 Modem will be fully functional and ready for operation.
The CN3200 modem will provide any Internet-ready device the ability to connect to a public
network via both xMax and WiFi using a hardwired connection to either an Ethernet switch/hub or
an external WiFi hotspot connected through the Ethernet port on the CN3200. The switch/hub or
hotspot is not provided and must be purchased separately.
Devices may also be connected to the xMax network through a wired Ethernet connection to the
CN3200 Modem.
For more information, see Wired Internet Connectivity and Setting Up a WiFi Hotspot on page 35.
NOTES
This procedure should be completed before installing the CN3200 Modem in a service location.
The setup sequence assumes that the CN3200 Modem device is in factory-default
configuration and has not been previously configured.
IMPORTANT: BEFORE YOU CONTINUE
Antennas or dummy loads MUST be connected to the two top Tx RF ports.
The CN3200 Dual Band Routing Modem is powered through the Ethernet cable. PoE (Power-over-
Ethernet) is a standardized system which passes electrical power along with data on Ethernet
cabling.
After terminating the Tx RF ports, connect the provided PoE++ Power Supply, as shown:
DO NOT plug the power cord into the AC outlet until directed.
Private
Network
110-240 VAC,
50-60 Hz
PoE++
Power Supply
DATA OVER
ETHERNET
POWER
plus DATA
CN3200
TERMINATE
BEFORE
POWER UP

14
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
1. Use a laptop or desktop computer to configure the CN3200 Modem.
Ensure that the computer network adapter is configured to Obtain an IP address automatically,
and if DNS servers are static, change the setting to Obtain DNS server addresses automatically.
2. Using an Ethernet cable, connect the computer to the Ethernet connector on the CN3200 Modem.
3. Connect the power cable on the PoE++ Power Supply to a 110 to 240 VAC power source.
The Status LED glows RED within fifteen seconds after the power source is switched on.
NOTE
The CN3200 Modem start up process takes approximately two minutes.
Before continuing, wait until this process completes and the LED glows GREEN.
1. On the computer, open a Web browser.
2. In the browser address line, enter the IP address to open the CN3200 Modem management
window:
CN3200 Modem xMax Network Management
xMax Network IP Address:
https:// 192.168.88.1:8081
3. In the User name and Password fields enter:
User name:
admin
Password:
admin1
The password is case sensitive.
The CN3200 Modem Management window opens to the Status page.
xG Technology strongly recommends that you change the User Password.
4. The menu bar is at the top of the window. To change the User Password, on the right side of the
menu bar, click Admin.
NOTES
The Password is case sensitive.
Before clicking Enter, be sure to write down the new password for future reference:
New Password:

15
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
Enter the User Password, and then click Enter.
The message User password was successfully updated is displayed.
NOTE
DO NOT SET OR USE THE WIFI OPTION WITH THE CN3200 Modem.
5. At the bottom of the page, click Save Changes, and then on the right side of the menu bar,
click Logout to complete the configuration process.
6. Restore the network adapter to its previous settings.
1. In the browser address line, enter the IP address to open the WiFi Network Management window:
CN3200 Modem WiFi Network Management
WiFi Network IP Address:
http://192.168.88.1
2. In the User name and Password fields enter:
User name:
webadmin
Password:
(NULL)
The password is case sensitive.
The first time the interface opens, a warning displays that no password is set.
xG Technology strongly recommends that you create a Password.
3. Click Go to password configuration… in the message box at the top of the window.
Before clicking Save & Apply, be sure to write down the new password for future reference:
NOTE
The password is case sensitive.
New Password:
4. On the Router Password page, enter the new password in the Password field, and then enter it
again in the Confirmation field. Click Save & Apply.
NOTE
To change the password in the future:
On the bar at the top of the window, hover over the Network and then click Administration on the
drop down menu to open the Router Password page.

16
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
Connect to the WiFi Access Point
1. On theTool Bar at the top of the window, hover over Network and then click WiFi on the drop
down menu.
2. On the Wireless Overview page, click Scan.
All available CN1300 WiFi Access Points display in the Associated Stations section.
3. Select a listed WiFi AP by SSID and then click Join Network.
4. On the Join Network: Settings page, enter the passphrase for the WiFi AP in the WPA passphrase
field.
5. In the Name of the new network field, ensure that the value is wwan (lower case).
6. In the Create / Assign firewall-zone section, click to select the wan: radio button,
and then click Submit.
7. On the Wireless Network: Client page, click the General Setup tab in the Device Configuration
section, select the required Transmit Power from the dropdown menu.
8. Click the Advanced Settings tab of the Device Configuration section, and then select the desired
Country Code from the dropdown menu.
9. Continuing in the Wireless Network: Client page, scroll down to the Interface Configuration
section, and then click the Wireless Security tab.
10. Confirm that the displayed Key matches the WPA passphrase set in Step 4.
NOTE
If the passphrase is not visible, click the green reveal toggle icon to the right of the field to display it.
11. Click Save & Apply.
The WiFi network is now available.
IMPORTANT
All other configuration settings must remain unchanged.
Only an advanced user should attempt to adjust any other settings.

17
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
The CN3200 Modem is a 2x4 MIMO device with four antenna connectors —two Tx/Rx and two
Rx-only.
All connectors are always used.
Omni, Panel and Sector antenna configurations are supported.
For optimum performance, the CN3200 Modem should be placed as close as possible to the
antennas.
The antenna cable lengths should be as short as possible.
The GPS antenna can be mounted in any convenient location.
FOR OPTIMUM PERFORMANCE
The cables from the two Tx/Rx connectors on the CN3200 Modem should be connected
to the two antennas on one diagonal.
The cables from the two Rx connectors on the CN3200 Modem should be connected
to the two antennas on the opposite diagonal.
IMPORTANT
UV-resistant CMX outdoor-rated, Cat 5e UTP Ethernet cable MUST be used.
Foil-shielded cable is recommended in areas requiring protection from EMI, RFI, or cross talk.
Failure to properly install the provided IP68-rated Weatherproof Ethernet Power Connector
may lead to product failure, and void the product warranty.
For additional information, please refer to the Antenna Configuration illustration on page 18.

18
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
This is a typical tower-mounted CN3200 Modem installation with a 2x4 MIMO Panel Antenna.
IMPORTANT
Install the provided six (6)
ferrite beads as shown
by this marker
in the wiring diagram.
xMax
ANTENNA
2.4 GHz
ANTENNA
110-240 VAC,
50/60 Hz
PoE++
Power
Supply
PoE
Surge
Protector
ETHERNET
DATA
POWER
plus DATA
xMCC
PoE Surge Protector
Grounded at Building Entry
Figure 1 —Antenna Configuration
Tx/Rx Tx/Rx
1 3
H V
Rx Rx
4 2
V H

19
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
NOTE
xG Technology recommends that the CN3200 Dual Band Routing Modem be configured on a bench
before installing the device in the field. Please refer to the topic Configuring the CN3200 Dual Band
Routing Modem on page 13.
This checklist may assist you in assembling the parts needed to complete the installation.
CN3200 Dual Band Routing Modem
SUPPLIED BY xG Technology
OBTAIN FROM YOUR PART SUPPLIER

CN3200 Modem
with Wall Mount Bracket

UV-resistant CMX outdoor-rated,
Cat 5e UTP Ethernet Cables
(4-6 mm OD; lengths as required)

Weatherproof Ethernet Kit

Data Cable Connectors (RJ45)

PoE++ Power Supply

Grounded PoE Surge Protector
(CTC Union SP-POE-01 or equivalent)

900 MHz Panel Antenna
and 4 Cables (SMA-Female)

2.4 GHz Panel Antenna
and Cable (TNC-Female)

Ferrite Beads

Alternative mounting solution
(as ordered)
Figure 2 —CN3200 Dual Band Routing Modem Parts Checklist
IMPORTANT
The provided weatherproof Ethernet connector requires the use of Ethernet cables with an outside
diameter of 4-6 mm.

20
CN3200 Access Point - Installation Guide - G7604 - Release 3.3
Installation Tool Kit Checklist

8 mm Metric Wrench

10 mm Metric Wrench

11 mm Metric Wrench

Cat 5 Crimp Tool

Digital Inclinometer
or
Magnetic Angle Locator

Magnetic Compass
or
Smart Phone
Compass App

Colored Weatherproof Tape
(if installing multiple units)
Figure 3 —Installation Tool Kit Checklist