Xiaomi Mi Motion User manual

Mi Motion-Activated Night Light (Bluetooth)
User manual

Read this manual carefully before use, and retain it for future reference.
Note: Illustrations of product, accessories, and user interface in the user manual are for
reference purposes only. Actual product and functions may vary due to product
enhancements.
Light Area
Sensor Area
Product overview
Magnetic Base
Bluetooth Switch
Battery Cover
Battery Compartment
Front
Interior
Adhesive Sticker
The night light can rotate 360 degrees

Turn the front cover counterclockwise to unscrew it from its hemispherical housing.
Open the battery cover and install three AA batteries in the battery compartment.
Installation
1. Installing the batteries
This product works with the Mi Home/Xiaomi Home app*. Use the Mi Home/Xiaomi
Home app to control your device, and to interact with other smart home devices. Scan
the QR code to download and install the app. You will be directed to the connection
setup page if the app is installed already. Or search "Mi Home/Xiaomi Home" in the
app store to download and install it.
Open Mi Home/Xiaomi Home app, tap "+" on the upper right,
and then follow prompts to add your device.
2. Connecting with Mi Home/Xiaomi Home App

Notes:
• Please connect with the app before installing the night light.
• Make sure the Bluetooth is enabled on your phone when connecting with the app.
• If the night light needs to be reconnected with the app, please delete this device from
the app and restore its factory settings first, then reconnect it.
• The version of the app might have been updated, please follow the instructions
based on the current app version.
* The app is referred to as Xiaomi Home app in Europe (except for Russia). The name
of the app displayed on your device should be taken as the default.
Choose a flat and dry place to install the night light.
Wipe the desired surface clean, then peel off the protective film from the adhesive
sticker of the base. Position the base on the surface and press it down firmly to make
sure it is properly secured. Then, install the night light onto the magnetic base and
adjust the angle as preferred.
3. Mounting the light

Note: For accurate detection, it is recommended to face the light downwards when the
base has been mounted over 1.9 m above the floor.
Note: For different mounting heights, the angle needs to be adjusted based on the
user's height and the desired usage scenario to achieve the optimal result.
Facing downwards
Mounting point is
over 1,9 m above the floor
Facing straight forward
Mounting point is between
0.5-1.5 m above the floor
Facing upwards
Mounting point is below
0.5 m above the floor

• The night light will turn on automatically when it detects human body motion in the
dark environment, and will turn off automatically after a while if no human body
motion is around.
• The night light function is enabled by default with its lighting up for 15 seconds in
2.5 lumens.
• You can enable or disable the night light function on the page of Mi Motion-Activated
Night Light 2 (Bluetooth) in the app. The brightness can be adjusted between 2.5 to
25 lumens and the lighting up time between 15 to 60 seconds.
Note:To do the settings or update the firmware in the app, enable the Bluetooth
function on your phone first, then move your body around within the induction range of
the night light or push the Bluetooth switch to either side.
• The night light has the sensor functions to not only detect the human body motion,
but also the ambient light status of bright or dark.
• You can access the night light to the devices that support Bluetooth gateway
function, such as the Mi Bedside Lamp and the Mi Smart LED Ceiling Light. Tap
Bluetooth gateway in the settings of the night light page in the app.
• After the night light is successfully accessed, then you can check the logs of the
human body motion and the ambient light status. You can also configure to interact
this night light with other devices in smart scenes.
How to Use
1. Night Light Function
2. Sensor Function

Note: You can view the logs only when the night light is accessed to the devices that
support the Bluetooth gateway function.
Note:
The detection area is a 120" area directly at the center in front of the night light. The
detection area covers 0-6 min front of the light, and 0-2.5 m to the sides. The detection
effect depends on the angle of the light, ambient temperature, body size, and moving
speed. The illustrated detection area is based on the direction the logo is facing.
Detection Area

Within two seconds, quickly press the Bluetooth switch to either direction three times.
Once the night light turns on and then turns off, the factory settings have been restored
successfully.
Restoring Factory Settings
Specifications
Model: MJYD02YL-A
Operating Temperature:
-10°C to 40°C
Compatible with:
Android 4.4 & iOS 9.0 or above
Wireless Connectivity:
Bluetooth 4.2 BLE
Rated Voltage: 4.5 V
Rated Power: 0.35 W
Item Dimensions: ø 80 × 62 mm
Net Weight: Approx. 121 g
Luminous Flux: 2.5–25 lm
Operating Frequency: 2402–2480 MHz
Maximum Output Power: ≤8 dBm

• Do not cover the detection area of the light.
• When cleaning the surface of the light, wipe it clean with a soft cotton cloth and do
not use any corrosive solvents.
• Do not install the light near heat sources such as AC or heating vents, or in direct
sunlight. Nor install the light near sources of humidity such as humidifiers or water
heaters.
• Make sure it is firmly installed with the magnet, so as to avoid the risk of accidental
dropping.
• Make sure the Mi logo is upright at all times when installing and using the night light.
• When the brightness of the night light is reduced after a period of normal use, the
battery level may be insufficient. Please replace the batteries with a new ones and
dispose of the used batteries in accordance with local rules and regulations, so as to
avoid environmental pollution.
• The light source contained in this luminaire shall only be replaced by the
manufacturer or his service agent or a similar qualified person.
• For indoor use only.
• Please pay attention to the positive (+) and negative (-) poles when installing the
batteries.
• After non-rechargeable batteries are depleted, they cannot be charged. Different
types of batteries, and old and new batteries should not be mixed.
• Remove leaking batteries from the night light, and dispose of them in accordance
with local rules and regulations, so as to avoid environmental pollution.
• The batteries must be removed from the night light when it is not used for a long
time, or when the night light is being disposed of.
• Under normal use of condition, this equipment should be kept a separation distance
of at least 20cm between the antenna and the body of the user.
Precautions

Hereby, Qingdao Yeelink Information Technology Co., Ltd. declares that the radio
equipment type MJYD02YL-A is in compliance with Radio Equipment Regulations
2017. The full text of the UK declaration of conformity is available at the following
internet address:
http://www.mi.com/uk/service/support/declaration.htmI
UK Declaration of Conformity
Hereby, Qingdao Yeelink Information Technology Co., Ltd. declares that the radio
equipment type MJYD02YL-A is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet address:
http://www.mi.com/global/service/support/declaration.html
EU Declaration of Conformity

WEEE Disposal and Recycling
All products bearing this symbol are waste electrical and electronic equipment (WEEE
as in directive 2012/19/EU) which should not be mixed with unsorted household
waste. Instead, you should protect human health and the environment by handing over
your waste equipment to a designated collection point for the recycling of waste
electrical and electronic equipment, appointed by the government or local authorities.
Correct disposal and recycling will help prevent potential negative consequences to
the environment and human health. Please contact the installer or local authorities for
more information about -the location as well as terms and conditions of such
collection points.

FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To satisfy FCC&IC RF exposure requirements, a separation distance of 20 cm or more
should be maintained between the antenna of this device and persons during device
operation.
To ensure compliance, operations at closer than this distance is not recommended.
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Qingdao Yee link Information Technology Co., Ltd.
(a Mi Ecosystem company)
Address: 10F-B4, Building B, Qingdao International Innovation Park, No.1 Keyuan Weiyi
Road, Laoshan District, Qingdao City, Shandong Province, P.R.China
For further information, please go to www.mi.com
Importer:
Beryko s.r.o.
Na Roudné 1162/76, 301 00 Plzeň
www.beryko.cz