XKGlow XKchrome Cube Light Series User manual

XK065 XKchrome Cube Light Series !!!!!!!!!!!!!!!!!!!!!!!!!!!!! !
!
Input
Voltage
Power per unit
12V DC
20w
Warranty and Disclaimer
XKGLOW products that have one or more LEDs fail to illuminate due to a defect in materials or workmanship
are covered with a THREE year warranty for the original buyer.
Installation of this product must be performed by a licensed professional. Should the failure of the product
be the result of damage occurring as a result of improper installation, alteration of the product or an act or
omission on the part of the consumer, this warranty is void. XKGLOW Lighting shall not be responsible for
any consequential damages which arise from the use and/or installation of the product. If the kit is installed in
any manner other than specified, XKGLOW Lighting reserves the right to deny any warranty claims at the
discretion of the technical support department. Any product return must include the original packaging,
invoice number and a statement of the alleged defect. Upon receipt of the returned product, the company will
test the product for defect. If the results of the testing do not support the warranty claim, do not reveal any
defect or indicate consumer negligence in the installation and handling of the product, then the product will be
returned to you and you will be charged a reshipping fee. If the product is returned from an address within
the continental United States, within the first 30 days after purchase, and is found to be defective, XKGLOW
Lighting will exchange or refund the original purchase expense. This offer does not extend to the cost for
shipping charges on any international packages.
Additional Disclaimer Terms
Please check your local and state laws for the proper use of this product.
• Improper installation of electrical products such as lighting may cause damage to any vehicle or device to
which the improperly handled or installed lighting is attached.
• Improperly installed product may cause electrical injury to persons.
• It is recommended that the kit should be installed by a licensed professional.
• XKGLOW assumes no liability for the installation of the product.
• Warranty or liability will not exceed the product purchase price, which shall be buyer’s sole and exclusive
remedy.
Return/Exchange Procedure
1. Email [[e-mail]] to notify us of the product issue as well as the item number and name of
customer on invoice.
2. We will send you the trouble-shooting guide to fix the issue, or to narrow down which of the component(s)
need to be replaced. If the issue still exists, we will ask you to send back the defective items to be
replaced.
3. Please send the returned item as instructed, along with claims and a telephone number where you can
be reached.
4. After the returned item(s) have been accepted and inspected, we will issue a refund or replace the items
ASAP. For refunds, item(s) must be sent to XKGLOW within 14 days from date of purchase. Original
shipping charges are not refundable.
We always stand behind our products and are committed to our customers! For questions you may
have, please contact [e-mail]. We normally respond within 24 hours. (Monday-Friday).

XK065 XKchrome Cube Light Series !!!!!!!!!!!!!!!!!!!!!!!!!!!!! !
!
Mounting Instructions
1. Test all components before mounting: As shown below, plug ALL light units together and connect them
to the controllers and the switch wiring harness. Connect the RED battery terminal to the POSITIVE pole
of 12V DC battery. Connect the BLACK battery terminal to the NEGATIVE pole. Turn on the switch and
push the controller buttons to test the pods. If the lights show any defects, please contact us and we will
be happy to replace them for you.
2. Optional- Sensor wire: The controller comes with an options sensor wire. The default triggered sensor
action is turning all lights to red. This action can be customized in the Device List section within the
XKchrome app. This wire must be tapped into 12V+ wire, such as brake light or revers light for it to be
properly triggered.
3. Install cube light: Use supplied mounting accessories to securely mount the cube lights.
4. Route power wiring harness: Mount the ON/OFF switch in a convenient location. Using zip ties, secure
any loose wiring.
5. Install XKchrome Controller: Plug the XKchrome Controller into the DC plug from the power wiring
harness. Connect the controller and the lights using supplied splitter and extension wires.
6. Power on, download the XKchrome App, and enjoy!
Please note: There are multiple XKGLOW apps
on the App Store. Only the XKchrome App will
work with the XKchrome Bluetooth Controller.
The App icon is pictured here.