XPOtool 63323 User manual

User’s manual
Thread Repair Kit
63323
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

https://www.XPOtool.com Item 63323 Page 2
The Tool Experts
07 2022-1
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

https://www.XPOtool.com Item 63323 Page 3
The Tool Experts
07 2022-1
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Safety instructions
•During use, wear suitable protective clothing, especially protective goggles and work gloves.
•Only use the tool and its accessories properly. Improper use might lead to property damage and
personal injury.
•Before every use, check the tool for damages or wear and tear. Should you detect any of them,
the tool must not be used any longer.
•Do not try to extend the lever of the tool holders with the help of other objects (e.g., tubes).
•Always clamp the tool and work pieces firmly and securely.
•It is advisable to always use cutting oil.
•Do not recut a thread in case you do not know about its exact type and size.
•Choose the correct core hole size and bolt diameter.
•Clean the tool and its accessories after every use and remove chips with appropriate devices.
Never clean them bare-handed.
•Before use, always check the type and size of the thread.
Use
Drilling
•Use a standard drill to drill out the damaged thread. The correct drills are included up to to size
of M12 (½″).
•If using the particular spark-plug-bore drill, you will not need to pre-drill the thread. Please note
that you larger holes are required if using thread moulders.
Checking
Check the thread and pitch of the thread drill to know if they match the screw.
Thread-cutting
•With the use of the special thread drills, cut the mounting thread into the pre-drilled hole.
•It is advisable to use an appropriate cutting oil.
Installing the inset
•Set the inset on to the mounting tool and position the adjustable ring so that the pin of the
mounting tool is centred in the pin slot.
•With a slight pressure, turn the inset in down until it is half a turn beneath the surface.
•Do not turn against the direction of the thread, as the pin could break.
Removing the pin
•After finishing, lift the mounting tool and use the pin-breaking tool to remove the pin.
•When working on larger sizes or spark-plug thread, use needle-nose pliers to remove the pin.
•Thanks to the narrow and precise tolerances, the new thread is normally stronger than the old
one.

https://www.XPOtool.com Item 63323 Page 4
The Tool Experts
07 2022-1
Step 1
Drill out the damaged thread with a correctly
sized drill (included).
Step 2
Finish the pre-drilled hole with the thread drill in-
cluded.
Step 3
Set the spiral inset into the applicator.
Step 4
Screw in the spiral into the cast piece.
Step 5
Use the breaking tool to break off the pin of the
spiral inset.
Step 6
The thread is repaired and ready for use.
Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission
of WilTec Wildanger Technik GmbH.