Xpresskit DBALL2 User manual

Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Vehicle Application Guide...................................................................................................................................................
Key2GO & 1KEY................................................................................................................................................................
Installation (Wiring Diagram & Vehicle Wiring Reference Chart)........................................................................................
Programming
Module Programming.........................................................................................................................................................
Module Reset.....................................................................................................................................................................
Hard Reset.........................................................................................................................................................................
Feature & Option List..........................................................................................................................................................
Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Limited One-Year Consumer Warranty...............................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
03
04
06
08
08
09
10
11
13
14
Index
The CHRYSLER14 firmware for DBALL2 is an all-in-one door lock and override module compatible
with specific Chrysler vehicles.
This module can only be flashed and configured using XpressVIP at www.directechs.com or
using the Directechs Mobile application for smartphones. Refer to the Module Programming
section on page 6 for more information.
® Chrysler is a registered trademark and property of Chrysler Group LLC.
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Vehicle Application Guide Page 2
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for
more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicles
2017 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control CC-Heated Mirrors CC-Heated Seats Activation DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote Key2GO RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-E-Brake Status ST-Ignition Status
Chrysler
Pacifica (Smart Key) • • • • • • • • • • • • • D • • • • • D • • •
Legend:
D: Data-to-Data (D2D) only AV: Horn & Lights Controls
•: D2D and Wire-to-Wire (W2W) CC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Page 3
This feature is mandatory to control the immobilizer override in this firmware.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses
an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to
give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also
appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information
will be required to complete the registration process, such as your Directed account number and store name. Key2GO
requires an XKLoader.
Refer to page 7 of this guide for instructions on how to program features using Key2GO.
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Remote
Starter
(-) GWR (Status)
(-) Lock Output
(+) Starter Output
(-) Unlock Output
(-) Trunk Output
(-) AUX2 Sliding Door (passenger side)
(-) AUX1 Sliding Door (driver side)
(+) Parking Lights Output
(+) Ignition Output
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
7: Pink/White: (+) Parking Lights Input
10: Blue/White: (-) GWR (Status) Input
Parking Light Interrupt (vehicle side): Yellow: 8
CUT
(MUX) Parking Light Input.: Brown: 7
HS CAN 1 High: Tan/Black: 3
HS CAN 1 Low: Tan: 4
Parking Light Interrupt (conn. side): Orange/Yellow: 9
(+) Brake Output: Gray: 6
[2] (-) Hood Status Output: Blue/Red: 12
(+) Ignition Status Output: Gray/Black: 7
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1] (-) (AC) Tach Output: Violet/White: 5
(-) Ground: Black: 14
(+) 12V: Red: 13
(MUX) Parking Light:
White/Brown, pin 1
(+) Ignition/Start Enable:
Pink/White, pin 27
Not required in D2D mode.
HS CAN 2 Low: Orange/Brown: 6
HS CAN 2 High: Orange/Green: 5
Headlight switch
(Black conn. at
Headlight Switch)
12 3 4
9876
5
10
1 8
169
C-CAN High:
Gray/White, pin 6
IHS CAN High:
Gray, pin 3
C-CAN Low:
Yellow, pin 14
IHS CAN Low:
White, pin 11
OBDII
Diagnostic
Connector
(-) Ground
(+) Ignition/Start Enable Input: Brown/Red: 12
(+) Ignition/Start Enable Output: Yellow/Red: 11
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(+) Brake Input
[2] (-) Hood Status Input
(-) E-Brake Status Input
(-) Ground
(+) 12V
4: White/Violet: (-) Sliding door (pass. side)
5: Violet/Black: (-) Sliding door (driver side)
38
10
32
18
35
7
29
15
37
9
31
17
34
6
28
14
26
12
36
8
30
16
33
5
27
13
25
11
48
24
45
21
47
23
44
20
46
22
43
19
42
4
41
3
40
2
39
1
BCM
(Black conn. located at BCM,
above driver kick panel)
BCM
(Gray conn. located at BCM,
above driver kick panel)
Resistor
550W
BCM
1
3
2
4
(+) 12V:
Red, pin 3
Wiring Diagram
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Some vehicles are not equipped with OEM hood pin and require the addition of a hood pin for hood sensing.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
10
DBALL2
RF
Prog. Button
LED
4
TX
(-) Ground
RX
(+)12V
14 12 2
P#: XKD2D65
Page 4
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.
Page 5
Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Chrysler Pacifica (Smart Key) 2017
12V Red 3 (+) Located at BCM. Gray 4
Parking Lights White/Brown 1 MUX Parking Lights Switch. Black 10
C-CAN High Gray/White 6 Data Located at OBDII. Black 16
C-CAN Low Yellow 14 Data Located at OBDII. Black 16
IHS CAN High Gray 3 Data Located at OBDII. Black 16
IHS CAN Low White 11 Data Located at OBDII. Black 16
Ignition/Start Enable Pink/White 27 (+) Located at BCM. Black 48
Wire Information Connector Information

Module Programming
Page 6
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Refer to the LED Diagnostics section on page 11 for more information and for troubleshooting purposes.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to
the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the
module, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
10-pin
D2D
st
1
th
4
12-pin
14-pin
nd
2
rd
3
2
Go to the next page to complete the module programming.
1
Solid
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features only, press
the programming button 5 times. The LED will turn orange then proceed to step 2.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Flash Module button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
3
If the transponder programming was skipped, the
LED turns ON solid orange for 3 seconds then shuts
OFF when programming is done.
Cycle ignition ON & OFF by
pressing Push-to-Start button twice
then once, until LED flashes orange
slowly. It may take up to 10 times.
&
Flashes
green
fast
Flashes
orange
fast
Flashes
orange
slowly
&
&
( )X10
Up to:
2X ENGINE
START
STOP
PUSH
1X ENGINE
START
STOP
PUSH
ON OFF
Disconnect the module and complete the Key2GO programming.
Make sure ignition is OFF.
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Page 7
You have successfully completed the module programming sequence.
3
2
1
Once the configuration is completed, reconnect the module.
The LED turns ON solid green for 3 seconds, then turns off.
Click on Submit Key2GO Request.
Remove the module from the vehicle and reconnect it to your computer. The web site will automatically
recognize that you are moving onto the second phase of the programming sequence.
Refer to the LED Diagnostics section on page 11 for more information and for troubleshooting purposes.
Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.
Web Programming (for Key2GO)
Solid x3 Secs
&
Off
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1OR
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
10-pin
D2D
st
1
th
5
12-pin
14-pin
nd
2
rd
3
th
4
Module Reset
Hard Reset
2& &
Solid Solid
Release
Wait 3 seconds until the LED turns ON solid orange then release the
programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
Page 8
1OR
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
10-pin
D2D
st
1
th
5
12-pin
14-pin
nd
2
rd
3
th
4
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Page 9
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module
flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is
possible using the information on this page.
* Default Option
Feat. Operation Flashes / Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver priority* Unlocks only the driver door when the button is first pressed, and unlocks all doors
when it is pressed a second time within 5 seconds.
2. All Unlocks all doors when the button is first pressed.
1. Disabled* No operation.
2. Enabled When the feature is enabled, it will activate the Heated Seats and heated steering
wheel.
1. Disabled* No operation.
2. Enabled When the feature is enabled, it will activate the rear defroster and heated mirrors.
1. 32 °F (0 °C)* When Heated Seats or Defroster feature is enabled, it will activate the feature upon
remote start when temperature is below 32 °F (0 °C).
2. 23 °F (-5 °C) When Heated Seats or Defroster feature is enabled, it will activate the feature upon
remote start when temperature is below 23 °F (-5 °C).
3. 41 °F (5 °C) When Heated Seats or Defroster feature is enabled, it will activate the feature upon
remote start when temperature is below 41 °F (5 °C).
4. Always ON When Heated Seats or Defroster feature is enabled, it will activate the feature at any
temperature.
1. High* When Heated Seats are activated, they will be set to HIGH.
2. Low When Heated Seats are activated, they will be set to LOW.
1. Disabled* The vehicle doors will not lock automatically.
2. Ignition The vehicle doors will lock when ignition is turned ON and unlock when ignition is
OFF.
3. Brake The vehicle doors will lock when the brake pedal is applied and unlock when ignition
is OFF.
1. Disabled
The OEM alarm will not be controlled by the interface upon remote start. No disarm or
arm command will be executed at the beginning or end of the sequence; it must be
controlled by the Remote Starter.
2. Safelock
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote
starter. It will unlock at the beginning of the sequence, and relock after start and
shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm
and rearm the vehicle in the remote start sequence, only when required. Smart OEM
Alarm Control will monitor the alarm and door lock status to detect if the disarm or
rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed.
8Smart OEM
Alarm Control
4 Defroster
5
Heated
Seats/Defroste
r Temperature
Control
6Heated Seats
Temperature
7
Automatic
Controlled
Door Lock
1RFTD Output
Type
2Unlock Driver
Priority
3 Heated Seats
Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.

Rev.: 20170206
Platform: DBALL2
Firmware: CHRYSLER14
© 2017 Directed. All rights reserved.
To enter feature programming routine
-Turn the ignition ON, then OFF.
-Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
-The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat
until a new command is entered.
Changing feature options
-Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
-The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature
-Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
-Other features can be programmed.
-The feature programming can be exited.
Exiting feature programming
-No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.
OR
-Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
end of the programming sequence.
Feature Programming Programming
Button
Page 10