Xprinter P501A User manual

the printer enters the working state,and the power green indicator is on.
Printer 1PC
Data cable 1PC
Battery 1PC
User manual 1PC
Paper roll 1ROLL
Printer
Battery
User manual
Paper roll
Data cable
Button name,Indicator Light and Buzzer function:
Power button
a.Turn on: Press and hold the power button 2 seconds when the power is off,
b.Turn off: Press and hold the power button 3 seconds during the power-on
state,the printer power is off,and all the indicators are off.
Battery housing

25 seconds after the printer’s
green indicator flashes and the buzzer rings then release the FEED
button.At this point,the initialization has been completed.Press the
POWER button again to start up and work normally.
2
Print-head cleaning:
Timely clear printer-head in one of the below cases:
1. Unclear printing.
2. Unclear vertical column in printing paper.
3. Loud noise when feeding.
Cleaning steps are as follows:
1. Turn off the printer and open the top cover. Remove the paper if any.
2.Temperature of print-head can be very high right after finishing the printing task.
4.Turn on the printer and continue print task after the absolute ethyl
Then printer self-test page.
1.Please make sure power off when maintaining printer.
2.Don’t touch or scratch printing head surface by hands or metal materials.
3.Avoid using gasoline, acetone or other organic solvent.
alcohol completely volatilized.
Please clean print-head after it cools down to environment temperature.
3. Clean the thermal elements of thermal head with a soft cotton cloth moistened
with absolute ethyl alcohol.
4. Close the top cover after the absolute ethyl alcohol completely volatilized.
Power Button
Bluetooth Indicator
STATUS Indicator
FEED Button
Power Indicator
Power Indicator
Bluetooth Indicator
STATUS Indicator
Buzzer
Out of paper and overheating,the buzzer sounds every 2 seconds.
Bluetooth connection :The buzzer rings once.
Press this button to feed paper.If you press this button for a long time,
the paper will be fed continuously.
When the red light goes out,indicating the battery is full.
The green light indicates the starting state,and the red light indicates
the charging state.
Green light means bluetooth connection;Green light goes out means
bluetooth is disconnected.
Red light is always on and buzzes,the printer is in the state of paper
shortage;The red light goes out after the paper is checked.
Interface
USB Interface
USB can communicate and transmit data;
Rechargeable:recommended charging power 5V/2A (sold without
power adapter).
Cautions:
1.The printer can only work with the dedicated battery & power adapter.
2.If the printer will not be used for a long period of time, the battery must be
3.The fluid of battery used in the printer is caustic. If accidentally the battery
5. Although the printer can work in environment temperature between 0℃ to 40℃,
4.The printer must not be put into water or exposed to rain. Otherwise, it may
Otherwise, it may cause harm to the printer.
taken out of the printer. Otherwise, it may cause battery leakage.
leaks and the fluid is put on skin or clothes, please flush with running water
immediately. And if the fluid gets into eyes, please go to hospital immediately.
cause harm to the printer.
it may affect printing quality if environment temperature is too low or too high.
Federal Communications Commission Notice
This device complies with Part 15 of the FCC Rules and with Industry
Canada licence-exempt RSS standard(s).Operation is subject to the
following two conditions:
this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure condition
without restriction.
6