XtendLan XL-HBW128C User manual

M73-APOxx-xxx
128Mbps
HPNA3.0 over Coax
Ethernet Bridge
S
Sp pe ec ci ia al l E Ed di it ti io on n
f
fo or r M MD DU U E EP P
User’s Guide
V1.3
- 1 -
INTRODUCTION
This HCNA (HomePNA3.0 over Coax) to Ethernet
bridge connects any Ethernet device to a high speed
access network or to a LAN for Internet access. This
bridge brings you the newest Ethernet compatible
technology that uses the coaxial cable as the
network's physical wiring thereby eliminating the
need to install new wiring. It is designed to operate on
the coaxial cable installed in building.
This bridge allows you to connect PCs and Ethernet
enabled devices, such as STB and VoIP gateway, to a
LAN by simply plugging into the existing coaxial F-
Type connector.
Features
•Plug & play, as EP (Endpoint) while connects to a
Coax network controlled by MDU Master bridge
•Using existing coaxial cable to build a home
network
•Shares high speed Internet access and streaming
video
•1 port 128Mbps connection compliant with
HomePNA 3.0 over Coax (HCNA) standard
•2 standard 10/100BaseT fast Ethernet ports
•10/100Mbps auto negotiation support
•MDI/MDIX auto crossover support
•QoS priority mapping support
- 2 -
HARDWARE INSTALLATION
Parts Names and Functions
LED Indicators on the Front Panel
LED Status
Glowing Dimming Flashing
cPower Powered by
DC5V
Not powered N/A
dLAN
Link /Act
LAN 1
Link
Disconnect or
Link fail
Receive or
Transmit
eLAN
Link /Act
LAN 2
Link
Disconnect or
Link fail
Receive or
Transmit
fHCNA
Link /Act
HCNA
Link
Disconnect or
Link fail
Receive or
Transmit
gHCNA
SyncMode
Sync. Mode Async. Mode N/A
Ports on the Rear Panel
- 3 -
Port Name Type Functions
ADC5V DC Connect to the power adapter plug
BDIP Switch DIP Reserved
CLAN1/LAN2
(Ethernet) RJ-45 Connect to Ethernet port of PC or
STB or VoIP Gateway
DTV F Connect to TV
EHCNA F
Connect to F-Connector (on the
Wall) to HCNA MDU Master
bridge
Essential Hardwares
Items Included Description Purpose
HCNA to
Ethernet
Bridge
Main Unit
Coaxial
Cable
(F-Type/
RG-59U)
Connects from
HCNA port to
coax F-Type
connector on
the wall outlet.
CAT5
Ethernet
cable
Connects from
LAN port to
Ethernet
enabled
devices as PC
DC5V
Power
adapter
Connects from
power port of
the main unit
into a wall
outlet

- 4 -
Hardware Connections
1. Select a convenient location for the bridge near
the PC or STB or VoIP gateway. The bridge
should be kept away from excessive heat.
2. Using one coaxial cable to connect the HCNA
port to F-Type connector on the wall. Using
another coaxial cable to connect the other F-type
TV port to TV set.
3. Connect the LAN1/LAN2 port to your Ethernet-
equipped device (PC/STB…).
4. Connect the power adapter to the DC5V port
into a wall outlet.
The figure above shows how to connect to in-house
and in-building coaxial cable network, and to connect
any Ethernet device such as PC or STB or VoIP
gateway, to a coaxial cable network via the bridge.
- 5 -
Now you should have connected the LAN port,
HCNA port and the DC5V port to the appropriate
devices or lines. LED will be as:
POWER ON
LAN Link/Act ON
HCNA Link/Act ON
HCNA SyncMode ON
Note: Just Plug and Play simply, no further setting.
For more information on LEDs, see section
"LED Indicators on the Front Panel"
- 6 -
TROUBLESHOOTING
The bridge has been designed to be a reliable and
easy to use connection device. Please refer to the list
below to aid in troubleshooting.
The Power (green) LED is off.
Make sure the power adapter is properly
plugged into a live electrical outlet.
The LAN(Ethernet) or HCNA Link/Act LED is off.
Make sure the connection to these two ports is
secure.
The Ethernet or HCNA device to which you are
connected should be powered on and properly
configured.
The HCNA SyncMode LED is off.
Make sure if the coaxial cable is well connected
with the F-connector on wall. Occasionally, the
pin of coaxial cable may be not in a right
position and not properly connect with female
connector on wall.
“SyncMode” LED on the EP bridge will be ON
if there is a MDU Master bridge detected on the
coaxial cable. “SyncMode” LED, on the MDU
Master bridge will always be ON..
Please consult your service provider.
- 7 -
SPECIFICATIONS
Standards
IEEE 802.3 10BaseT Ethernet compliant
IEEE 802.3u 100BaseT Fast Ethernet compliant
HomePNA 3.0 over Coax (HCNA) compliant
Data Rates
HCNA: 128 Mbps
Ethernet: 10/100 Mbps
Distances
HCNA : 1200 meter maximum between the two
farthest nodes on LAN
Ethernet: 100 meter maximum
Power Consumption:
5V DC IN, Less than 4 watt
Certifications
VCCI, CE, FCC Part 15
LEDs
Power
Ethernet Link/Activity
HCNA Link/Activity; SyncMode
Connectors
Two F-Type connectors, one for connecting
with HCNA device, and one for TV
Two RJ-45 for 10/100M Ethernet
Cables
HCNA Network: F-Type RG-59U coaxial cable
Fast Ethernet: CAT5 or better UTP