XtremepowerUS 75030 Original instruction manual

ITEM #75030
POOL SAND FILTER 12" W/ PUMP 2400GPH 6VALVE
SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH
AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER).
OWNER’S MANUAL AND SAFETY INSTRUCTIONS
FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: [phone] MON-FRI 9AM TO 3PM PST

2
SAFETY INFORMATION
1. Thesand filters aredesignedtowork withwater attemperature>than 0 and<than 45 .The filter
should never beoperatedoutsideofthese temperaturesor damagemayoccur.
2. Theinstallationshouldbecarriedoutinaccordancetothesafetyinstructionsofswimmingpools andthe
specific instructions for eachfacility.
3. Theuser should makesurethattheinstallationis carriedoutbyqualifiedauthorizedpersons andthat
these personshavefirstcarefully readthefollowing instructions. Incorrectly installed equipment mayfail,
causing severe injury or propertydamage.
4. Theoperating safetyofthefilteris only guaranteedif theinstallationandoperationinstructions are
correctly followed.
5. Toreducetherisk of injury, donotpermit childrentouse this product.
6. Chemical spills andfumescan weakenSwimming Pool/Spa. Corrosioncan cause filters and other
equipment to fail, resulting in severe injury or propertydamage.Do not store pool chemicals near your
equipment.
7. Anymodificationofthefilter requires thepriorconsent from thesupplier’s original replacement partsand
accessories authorizedbythemanufacturerensureahighlevelofsafety. Thesupplier assumes noliability
for thedamageand injuriescausedbyunauthorizedreplacementparts and accessories.
8. Intheeventofdefectiveoperationor fault,contactthesupplieror its nearestauthorized service
agent.
Sand Filtrationsystem working principle
Incoming water from thepiping system is automatically directedbytheMulti-port Valvetothetop ofthefilter
bed.As thewater is pumpedthrough thefilter sand,dirt anddebris are trappedbythe filterbed, andfiltered
out.Thefilteredwater is returnedfrom thebottom ofthefiltertank, through theMulti-port Valveand back
through thepiping system.
Preparationbefore installation
1. Positionthefilter as close to theSwimming Pool/ Spa as possible.
2. Thefilter shouldbeplacedona level concreteslab, very firm ground, or equivalent.Ensure that theground
will not subside, preventing anystrainfromtheattachedplumbing.
3. Positionthefilterunder considerationofthepipingconnections, so thatitis convenientfor operating
and servicing.
4. Ensure thatthecompliancelabelis facing thefronttoalloweasy identificationinthecase of service
difficulties.
SAFETY INFORMATION

3
How to install the filter tank
1. Mount the Pump to sand filter support by using bolts and nuts.
2. Install the drain plug assembly to sand tank as below pictures.
3. Press and turn the sand tank to mount it to the sand filter support with correction direction (drain plug is on
the outside as below pictures).
INSTALLATION

4
4. Insert the tube with the diffuser body inside the tank as above picture, then place the funnel on the tank's
mouth and pour the quartz sand into the tank (about23kg)
5. Take away the funnel, and then please make sure tank!s neck is very clean. Put the O-ring on the valve and
use clamp to fix the valve with tank! (the direction of "PUMP# port on valve needs to face pump out port).
6. Connect the sand tank to pump with hose, hose clamps and hose adaptors.
INSTALLATION

5
INSTALLATIONNOTES:
1. Makesurethefilter is workedunder thework pressure,andusing a pressurecontrol valvewhen thesystem
using a booster pump.
2. Ifthepumppositionis higher thanthewater level, it requirestoinstall thebackwatercontrol valve.
3. Ifthepump positionis lower than thewaterlevel, itrequires installing an isolationvalve.It could stop
thewater return backwhenpeople do thegeneral inspection.
4. Reducingtheconnectadapters andhose connectingbendingas less aspossible.Decreasing the water flow
scrub, it could reachthemaximumeffective.
5. Ensure solvents arenotexcessively appliedtofittings as this couldrunintoO-ring and create sealing
problems.
6. Donotover tightenfittings or adapters.
HOWTO USE
1. Inspectthat all theconnections havebeenmadeare correct andsecure.
2. Depress the topmount valvehandleand rotatetothe BACKWASH position.
3. Prime and start the pump according to the pump instructions.
NOTE:ALL SUCTIONAND DISCHARGE VALVESMUST BE OPENING WHEN STARTING THE SYSTEM. FAILURETO
DO SO COULD CAUSESEVEREPERSONALINJURY.
MAKESURETHE FILTERVESSELAREFULL FILL THEWATERBEFORESTARTUP THE PUMP. ORITWILL CAUSE
THE PUMP DAMAGED.
4. Oncewater flowis steadyoutthewasteline,runthepumpfor atleast2minutes. Theinitial back-
washing ofthefilter is recommendedtoremoveanyimpuritiesoffinesandparticles in the sand media.
5. Turn pumpoff andsetvalvetoRINSE position.Startpump andoperateuntilwaterin sightglass is clear----
about 1/2to1minute.Turnpumpoff,setvalvetoFILTERpositionandrestart pump.Your filteris now
operating inthenormal filtermode, filteringparticles from thepool water.
NOTES:
1. Notetheinitial pressuregaugereading whenthefilteris clean.(it will vary from pooldepending uponthe
pumpandgeneral pipingsystem).As thefilter removes dirt andimpuritiesfromthepool water, the
accumulationin thefilter will cause thepressuretorise and flowtodiminish.Whenthe pressure gauge
reading is 8-10PSI(0.55-0.69BAR) higher than theinitial “clean”pressureyou noted, it is thetime to
backwash (clean)thefilter.
2. IMPORTANT:Topreventunnecessary strainonpiping system and valving, always shut off pump before
switching filtercontrol valveposition.
3. Toprevent damagetothepumpandfilter andforproperoperationofthesystem, clean pump strainer and
skimmer baskets regularly.
INSTALLATION

6
FILTER CONTROL VALVE FUNCTIONS
FILTER - Set valve to FILTER for normal filtering. Also used for regular vacuuming.
BACKWASH – For cleaning filter. When filter pressure gauge rises 8-10 PSI (0.55-0.69 BAR) above the initial
start-up pressure.
Stop the pump, set valve to BACKWASH. Start pump and backwash until water in sight glass is clear.
Approximately 2 minutes or less depending on dirt accumulation. Proceed to RINSE.
RINSE – After backwashing, with pump off, set valve to RINSE. Start the pump and operate for about 1/2 to 1
minute. This ensures that all dirty water from backwashing is rinsed out of the filter to waste, preventing
possible return to the pool. Stop pump, set valve to FILTER and start pump for normal filtering.
WASTE – To bypass filter for draining or lowering water level and for vacuuming heavy debris directly to
waste.
RECIRCULATE: Water is recirculated through the pool system, bypassing the filter.
CLOSED – Shuts off flow from pump to filter.
IMPORTANT: ALWAYS SWITCH OFF THE PUMP WHEN CHANGING VALVE’S POSITION.
INSTALLATION

7
Ref. N o. Par t N o . D escr ipt i o n QTY
1 47302502080 1
2 2
3 72712000 1
4 47303205080 5
5 2
6 5749017080 1
7 1
8
647201276000
Screw M6 X 25 an d Nut M6
1
9 1
1 0 1
1 1 1
1 2 1
1 3
97208 Ho se Clamp
1
1 4 1
47303005080
647304271000
647304272000
5024002000
47250501011
647303075
65760040000 Filter balls 700g
65653063001 Mesh bag
1
2
3
4
5
6
7
8
9
10
11
12
sand filtersupport
Pumpfor75030
Adaptorwith o-ring
1 1/4″32mm 35cmhosefor75030
7-WayValve
Flangeclamp
FilterAssembly
FilterTank
Pressure gauge
Drainplug
PARTS INFORMATION

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
',6&/$,0(5
PRODUCT MADE IN CHINA