Xylem YSI EXO PAR User manual

USER MANUAL
XA00014
EXO PAR
PHOTOSYNTHETICALLY ACTIVE RADIATION WITH THE EXO PLATFORM

The information contained in this manual is subject to change without notice.
Effort has been made to make the information in this manual complete, accurate, and current.
The manufacturer shall not be held responsible for errors or omissions in this manual.
Consult YSI.com for the most up-to-date version of this manual.
Thank you for purchasing a YSI EXO PAR System. This manual covers setup, operation, and functionality of the EXO
PAR system.
EXO PAR features include:
• Simple setup and operation
• Depth rating of 250 meters
• Single or dual sensor option
• Non-corrosive materials
• Data output in µmol s-1 m-2
• Use with Kor or EXO handheld
• Easily removed for non-par applications
Safety Information
Please read this entire manual before unpacking, setting up or operating this equipment. Pay attention to all
precautionary statements. Failure to do so could result in serious injury to the operator or damage to the equipment.
Do not use or install this equipment in any manner other than that specified in this manual.
The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,
without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent
permitted under applicable law. The user is solely responsible to identify critical application risks and install
appropriate mechanisms to protect processes during a possible equipment malfunction.
A
A
NOTICE: Indicates a situation which, if not avoided, may cause damage to the instrument
Precautionary Symbols
Product Components
Carefully unpack the instrument and accessories and inspect for damage. If any parts or materials are damaged,
contact YSI ISS at 727-565-2201 or authorized YSI distributor.
NOTE: Information that requires special emphasis
WARNING: Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death
or serious injury
CAUTION: Indicates a potentially hazardous situation that may result in minor or moderate injury
EXO PAR

When viewing this document as an AdobeTM
PDF, hovering your cursor over certain phrases
will bring up the finger-point icon. Clicking
elements of the Table of Contents, website URLs,
or references to certain sections will take you
automatically to those locations.
THIS IS AN
INTERACTIVE DOCUMENT
TABLE OF CONTENTS
1. Introduction
1.1 PAR Sensor
1.2 Overview
1.3 Components
2. Installation
2.1 Attach EXO Calibration Cup Extender
2.2 Attach the EXO PAR System Frame
3. Setup
3.1 Setup the Kor Software
3.2 Setup the EXO Handheld Display
4. Ordering
4.1 Ordering Replacement Components
4.2 Ordering

Introduction
4
1.1
1. Introduction
PAR Sensor
Some users of the YSI EXO sonde may wish to
incorporate a photosynthetically active radiation
(PAR) sensor into their field monitoring equipment.
This sensor can be added to the YSI EXO2 sonde
in the form of a special adapter engineered by
YSI’s Integrated System & Services division. This
appendix is designed to give potential users of
this PAR adapter information on how the system is
configured and the steps necessary to acquire and
log PAR data with the EXO PAR adapter.
1.2 Overview
Li-Cor PAR sensors are required for the EXO PAR adapter and these sensors can either be supplied to YSI by the
customer (brass mounting screws provided with the sensor are required for installing on the par system) or can be
purchased from YSI as part of the complete system. These sensors are then mounted to arms which extend from the
sonde on either side. Output cables are then attached to the sensors which connect to the EXO PAR adapter, which in
turn connects to the EXO2 Auxiliary port on the top of the sonde, as show in Figure 1.
Figure 1 shows the installation of two sensors (one pointing up, the other pointing down), but it is also possible to use a
single PAR sensor in either an upward or downward looking configuration.
Your EXO PAR system is shipped separate from your EXO2 sonde and can be installed onto the EXO2 sonde following
these easy steps.
TM
Figure 1 EXO PAR adapter with Sonde
TM

5
Introduction
1.3 Components
The EXO PAR Systems consists of 3 main parts: The EXO PAR adapter cylinder and cables, the black plastic frame
system and calibration cup extender, and the Li-Cor PAR sensors.
The EXO PAR system attaches to the EXO2 sonde via an upper and lower clamp system. The EXO PAR adapter
attaches to the AUX port on the top bulkhead of the EXO2 sonde. For shipment and storage, the EXO PAR system can
fold its sensor and support arms in, along the body of the EXO2 sonde (figure 2).
TM
TM
TM
Figure 2 The EXO PAR system attaches to the EXO2 sonde via an upper and lower clamp system

6Installation
2.1 Attach EXO Calibration Cup Extender
2. Installation
Once you’ve unpacked the EXO PAR system, attach the EXO calibration cup extender to the bottom of your calibration
cup. It simply clicks on by inserting the bottom of the calibration cup into the top of the extender and pushing down
on a hard surface (figure 3).
The calibration cup extender provides you the extra height you will need to prevent your PAR sensors and cables from
impacting the ground. It’s ideal for in lab use but we recommend using a lab stand as well for stability, to prevent your
sonde and PAR system from tipping over and potentially causing damage.
2.2 Attach the EXO PAR System Frame
Now that your calibration cup extender is installed, stand the sonde in an upright position and slide the EXO PAR
system frame over the EXO2 sonde. The two clamps; upper and lower are fastened to the EXO2 sonde body via two,
5/16-18 x 2.75” socket cap bolts. You will need to use a ¼” Allen wrench to secure these two bolts. Tighten the bolts
until the clamp fits snug to the body of the sonde. Proper alignment of these clamps, as described below, should be
followed as to not damage either system.
NOTE: Install the EXO PAR system with the EXO PAR adapter cylinder on the same side of the sonde where the
AUX port connector is located. You will connect the EXO PAR adapter into this AUX port.
Figure 3 Push down to mate the extender onto
the calibration cup.
CAUTION: Potential pinch hazard, be mindful of fingers.
Figure 4 The extender merged with the
calibration cup.

7
Installation
1. The top of the upper clamp should align with the yellow bulkhead of the sonde (where the blue meets the yellow).
Proper alignment is necessary so that the PAR sensor arms are deployed at the correct angle
NOTICE: Proper alignment of clamps is necessary to prevent damage.
2. The bottom of the lower clamp should align with the upper edge of the top chamfer on the clear plastic section
covered with the black “EXO²” sonde label. Again proper alignment is necessary so the PAR sensor arms are
deployed so that the PAR sensor faces axis is parallel to the sonde axis.
NOTICE: Proper alignment of clamps is necessary to prevent damage.
Figure 5 Align the upper clamps with the yellow bulkhead of the sonde
Figure 6 The lower clamp should align with the upper edge of the top chamfer on the clear plastic section

8Installation
4. After you have installed the upper and lower clamps, it’s time to address cable management. There are two cables
that connect to your PAR sensors coming from the EXO PAR adapter cylindar. Supplied with your EXO PAR system will
be several black, UV resistant Zip Ties. Fasten the sensor cables to the EXO PAR frame support arms as follows:
(3 locations)
NOTE: Dummy plugs are supplied for these cable’s connectors, plug these connectors when sensors are
removed or if only deploying 1 of your 2 PAR sensors. When not in use, the plugs can be stored in the
calibration cup extension.
Figure 8 Fasten the sensor cables to the EXO PAR frame support arms
3. Once you have the EXO PAR system secured to the EXO2 sonde body it is time to deploy the sensor arms. To do
so simply lift the arms and install the pins where the two arms meet, as shown (figure 7).
Figure 7 Lift the arms and install the pins where the two arms meet
CAUTION: Potential pinch hazard, be mindful of fingers.

9
Setup
3. Setup
Now that your EXO PAR system is installed, it’s time to connect your EXO PAR Sonde to either your PC running KOR or
your EXO handheld system. For PC applications, you can use the Bluetooth functionality of the EXO to connect with
KOR. For EXO handheld applications, you will need to connect an EXO field cable between the EXO communications
bulkhead connector and the EXO handheld communications bulkhead connector. The EXO field cable comes in
differing lengths depending on your needs, its part number is; 599040-xx (the –xx signifies the cable length; ex -2
equals 2 meters) Cable lengths start at 2 meters.
If the EXO PAR sonde is connecting to a data logger, you can use the EXO flying lead cable, part number 599008-xx
(again the –xx signifies the cable length) flying lead cables start at 10 meters. You will also need the EXO DCP adapter
to connect to a data logger, part number 599820.
Each Li-Cor PAR sensor is supplied with a Certificate of Calibration, shown below (figure 9). The calibration certificate
contains the multipliers for the sensor. YSI uses the in-water multiplier for our EXO adapter, providing PAR engineering
units out as data. In the following sections, we will review where and how to end this multiplier into either KOR EXO
software or the EXO handheld display.
Figure 9 Certificate of Calibration for Li-Cor Sensor

10 Setup
3.1 Setup the Kor Software
In the following steps we will cover the setup of the PAR sensor utilizing the YSI Kor software.
1. You will first need to enable the PAR(s) sensor in Kor. To do so you will need to select File, and then select
Settings, and from the list of parameters select PAR and you will see figure 8 if done correctly. From this window
you can enable either the PAR sensor or sensors by clicking the boxes shown.
Figure 10 Enable the PAR sensor in Kor
2. Using the Calibration Certificate supplied with your Li-Cor PAR sensor, you will now enter the multipliers into YSI’s
Kor software. To do so first select Instruments and Sensors and from the list of sensors displayed select PAR
sensor. If successful you will see the screen shown in figure 11. From the Calibration Certificate you will use the
In-Water multiplier that is listed under the Handheld Meters and Loggers section. You will enter the multipliers
exactly as they are on the certificates in the fields shown for Channel 1 and Channel 2. If you are only using one
PAR sensor, the default channel will be Channel 1. Leave the default value in Channel 2, which will be (1).

11
Setup
Figure 11 Enter the multipliers into YSI’s Kor software.
3. Now your PAR sensor(s) are ready to use. You can now see PAR data begin to show up in your Kor Dashboard
(example shown in figure 12).
Figure 12 PAR data will begin to show up in your Kor Dashboard

12 Setup
3.2 Setup the EXO Handheld Display
In the following section we will cover setting up EXO PAR utilizing the EXO Handheld Display.
1. You will first need to enable the PAR(s) sensor in the EXO Handheld. To do so you will need to select Handheld,
and then select Display, and from the list of Units select PAR and you will see figure 13. On the next screen you
can enable either the PAR sensor or sensors by clicking the boxes shown, figure 14.
Figure 13 Select PAR from the list
of Units
Figure 14 Enable sensors
2. Using the Calibration Certificate supplied with your Li-Cor PAR sensor, you will now enter the multipliers into EXO
Handheld Display. To do so first select Calibration and from the list of sensors displayed select PAR sensor. If
successful you will see the screen shown in figure 15. From the Calibration Certificate you will use the In-Water
multiplier that is listed under the Handheld Meters and Loggers section. You will enter the multipliers exactly as
they are on the certificates in the fields shown for Channel 1 and Channel 2 shown in figure 16. If you are only
using one PAR sensor, the default channel will be Channel 1. Leave the default value in Channel 2, which will be (1).

13
Setup
Figure 15 Select calibration, then
PAR from the list of sensors
Figure 16 Enter the multipliers
exactly as they are on the certificates
3. Now your PAR sensor(s) are ready to use. You can
now see PAR data begin to show up in your EXO
Handheld Display (example shown in figure 17).
Figure 17 PAR data on EXO
Handheld Display

14 Ordering
351070 EXO PAR Adapter Assembly
351073 EXO PAR, Upper Clamp
351074 EXO PAR, Lower Clamp
351075 EXO PAR, Wide Extension Arm (Lower)
351076 EXO PAR, PAR Sensor Bracket
351077 EXO PAR, Narrow Extension Arm (Upper)
351087 EXO PAR, Clip on Calibration Cup Extender
YSI Item # Description
4. Ordering
4.1 Ordering Replacement Components
4.2 Ordering
Telephone: [phone] (USA)
Monday through Friday
8:00 AM to 5:00 ET
Fax: [phone] (orders)
Email: YSISystemsOr[email protected]
Mail: YSI Inc - Systems & Services Division
Attn: Order Entry
7100 Business Park Drive, Suite B
Houston, TX 77041
When placing an order please have the following available:
1. YSI account number (if available)
2. Name and phone number
3. Purchase Order or Credit Card number
4. Copy of Quote (if applicable)
5. YSI Item Number or brief description
6. Billing and shipping addresses
7. Quantity

This page intentionally left blank

YSI.com/Systems
EXO is a trademark of Xylem or one of its subsidiaries.
© 2019 Xylem, Inc. XA00014 0719
YSI, a Xylem brand
7100 Business Park Drive, Suite B
Houston, TX 77041
+1.713.681.6101
[email protected]
YSI.com
1) The tissue in plants that brings water upward from the roots;
2) a leading global water technology company.
We’re a global team unified in a common purpose: creating advanced technology
solutions to the world’s water challenges. Developing new technologies that will
improve the way water is used, conserved, and re-used in the future is central to
our work. Our products and services move, treat, analyze, monitor and return water
to the environment, in public utility, industrial, residential and commercial building
services settings. Xylem also provides a leading portfolio of smart metering, network
technologies and advanced analytics solutions for water, electric and gas utilities. In
more than 150 countries, we have strong, long-standing relationships with customers
who know us for our powerful combination of leading product brands and applications
expertise with a strong focus on developing comprehensive, sustainable solutions.
For more information on how Xylem can help you, go to www.xylem.com
USER MANUAL XA00014