Yaesu BH-1 User manual

Controls & Connections
Microphone
POWER switch
VOLUME (–)switch
VOLUME (+)switch
LED Indicator
Blinking Blue: When the BH-1 Bluetooth®Head-
set is correctly recognized by the
transceiver.
Blinking Red: When the BH-1 Bluetooth®Head-
set is not correctly recognized by
the transceiver.
Blinking Red/Blue: Battery Voltage is Low.
PTT switch
Press this key to transmit. Release this key to return to
receive.
Earphone jack
If you use the Marine Transceiver, the BH-1 is not pos-
sible to listen to the stereo signal.
SPEAKER
Earhook
You can wear the BH-1 on your left or right ear.
“BH-1” Bluetooth®Head Set
When the optional BU-1 Bluetooth®Adapter Unit is installed, you may use the optional BH-1 Bluetooth®Head-
set as a wireless link to send and receive audio to the Transceiver*.
* Check with your Vertex Standard Dealer or Catalog for applicable models.
Pairing
Before you can use your BH-1 for the first time, the BH-1
and the transceiver must be paired.
Refer to the BU-1 Bluetooth®Adapter Unit Manual for Pair-
ing instructions.
PPlease bring the BH-1 and the Transceiver close together
when doing Pairing.
1. Make sure that the BH-1 is off.
2. Press and hold the POWER switch for five seconds, until
the LED indicator blinks red/blue alternately.
When the BH-1 is correctly recognized (Requires a 20 to 30
seconds) by the transceiver, the LED indicator will blink
blue.
Effective Communications Range
The communications range between the BH-1 and the
Transceiver is around 10m (33 ft).
Obstacles between the BH-1 and the Transceiver may
shorten the communications distance.
If you move out of range, the beeper sounds a low pitch
tone. If you move back into range, the beeper sounds a
high pitch tone.
Turning ON and OFF
TT
TT
To turn theo turn the
o turn theo turn the
o turn the BH-1 ONON
ONON
ON
Press and hold the POWER switch for three seconds, until
the BH-1’s LED indicator glows red, and the beeper sounds
a high pitch tone.
When the BH-1 is correctly recognized by the transceiver,
the LED indicator will blink blue.
PWhen the BH-1 is not correctly recognized by the trans-
ceiver, the LED indicator will blink red.
TT
TT
To turn theo turn the
o turn theo turn the
o turn the BH-1 OFFOFF
OFFOFF
OFF
Press and hold the POWER switch for five seconds, until
the BH-1’s red LED indicator blinks rapidly, the beeper
sounds two brief tones, and the BH-1 turns off.
NoteNote
NoteNote
Note : The BH-1 is automatically turned off when it is in-
serted into the CAB-2 charger.
LED indicator
POWER Switch
BH-1 is not designed to attach to a helmet.
Specifications are subject to change without notice.
Marine Division of VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
www.standardhorizon.com
EAF44U750
POWER Switch
All manuals and user guides at all-guides.com
all-guides.com

Wearing the BH-1
1. Open the earhook.
2. Loop the earhook over your ear.
3. Press the BH-1 to your ear.
4. Adjust the flexible boom microphone by bending the boom
towards your mouth.
The BH-1 comes ready to fit the left ear. You may change
the BH-1 to fit the right ear in the following procedure.
1. The Earhook is removed by pushing it out with a pointed
object.
2. Removed Earhook is inserted from the other side.
For more comfort when wearing the BH-1, affix the sup-
plied sponge on the speaker and insert the supplied sponge
ball into the earhook, and adjust as necessary.
Operation
TT
TT
Transmissionransmission
ransmissionransmission
ransmission
Press the PTT switch to transmit, and release the switch
to return to receive (Depends on transceiver settings).
Adjusting the VAdjusting the V
Adjusting the VAdjusting the V
Adjusting the Volume levelolume level
olume levelolume level
olume level
Adjust the receiver audio level, using the VOLUME (–)
or (+) switch.
VOLUME (+): Adjusts the receiver audio level upward.
VOLUME (–): Adjusts the receiver audio level downward.
Battery
When the battery voltage becomes low, the BH-1’s LED in-
dicator will blink red/blue alternately, the beeper sounds a
low pitch tone, and a “”icon will appear on the display of
the transceiver.
If the battery has never been used, or its charge is depleted,
it may be charged by connecting to the CAB-2 Charger
Sleeve, as shown in the illustration.
1. Attach the CAB-2 to the transceiver.
Please refer to the transceiver’s manual for installation of
CAB-2.
2. Insert the BH-1 into the CAB-2.
NoteNote
NoteNote
Note : The BH-1 is automatically turned off when it is
inserted into the CAB-2 charger.
3. If the BH-1 is inserted correctly, the LED indicator will
glow Red. A fully discharged battery will be charged com-
pletely in 3 hours. When charging is finished, the LED
indicator will glow blue.
VOLUME (+) Switch
VOLUME (–) Switch
PTT Switch
Battery saverBattery saver
Battery saverBattery saver
Battery saver
If there has been no signal or key activity for 20 seconds,
the Battery Save automatically puts the BH-1 to “sleep”, to
conserve battery life.
When a signal is received or the PTT key is pressed the
BH-1 will be active again.
Refer to the Transceiver Manual for Battery saver instruc-
tions.
Specifications
Bluetooth specification Ver1.2
Bluetooth profiles A2DP, HSP
Radio Frequency 2403 MHz - 2480 MHz
Modulation method GFSK
Transmitter output power 0 dBm Class 2
Receiver sensitivity <-80 dBm
Distance (open area) 32 ft (10 meters)
Audio format SBC
Audio frequency range 100 Hz - 20 kHz
Power supply Rechargeable Lithium-Polymer
Battery life 3 hours
Button/Switch Power On/Off, Volume Up/Down, PTT
LED indicators Power on: Flash blue twice
Unlink: Flash red
Link: Flash blue
Pairing: Red and Blue blinking
Battery low: Flash red and blue
Power off: Flash red 3 times
Operating temperature 32 °F to 104 °F (0 °C to 40 °C)
Operating humidity 5 - 90 %
Certification FCC, CE, BQB
Replacement Parts
Ear hook S8002323
Ear hook sponge S8002325
Speaker sponge S8002324
Wind Screen S8002322
CAB-2 Screw U23316027
All manuals and user guides at all-guides.com