Yamaha DVD-S1700 User manual

SERVICE MANUAL
101037
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
DVD AUDIO/VIDEO SA-CD PLAYER
DVD-S1700
P.O.Box 1, Hamamatsu, Japan
DVD-S1700
2006 All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
'06.12
■CONTENTS
TO SERVICE PERSONNEL ...................................... 2–4
PREVENTION OF ELECTROSTATIC DISCHARGE .... 4
LOCALE MANAGEMENT INFORMATION ................... 4
FRONT PANEL .............................................................. 5
REAR PANELS .......................................................... 5–6
REMOTE CONTROL PANEL ........................................ 7
SPECIFICATIONS / 参考仕様 ........................................ 7
INTERNAL VIEW ........................................................... 8
TRADE MODE / トレードモード ................................... 8
ERROR MESSAGE / エラーメッセージ ........................ 8
TROUBLESHOOTING / トラブルシュート ................... 8
DISASSEMBLY PROCEDURES / 分解手順.................. 9
DISPLAY DATA ........................................................... 10
IC DATA ................................................................. 12–30
BLOCK DIAGRAM ....................................................... 31
WIRING DIAGRAM ...................................................... 32
PRINTED CIRCUIT BOARDS................................ 33–36
SCHEMATIC DIAGRAMS ...................................... 37–42
REPLACEMENT PARTS LIST .............................. 43–45
REMOTE CONTROL .................................................... 46

DVD-S1700
2
DVD-S1700
WALL
OUTLET
EQUIPMENT
UNDER TEST
AC LEAKAGE
TESTER OR
EQUIVALENT
INSULATING
TABLE
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and
possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
1. Critical Components Information
Components having special characteristics are
marked sand must be replaced with parts having
specifications equal to those originally installed.
2. Leakage Current Measurement (For 120V Models
Only)
When service has been completed, it is imperative to
verify that all exposed conductive surfaces are prop-
erly insulated from supply circuits.
●Meter impedance should be equivalent to 1500 ohms
shunted by 0.15µF.
●Leakage current must not exceed 0.5mA.
●Be sure to test for leakage with the AC plug in both
polarities.
■TO SERVICE PERSONNEL
本機に搭載されているすべての基板およびハンダ付けによる接合
部は無鉛ハンダでハンダ付けされています。
無鉛ハンダにはいくつかの種類がありますが、修理時には下記の
ような無鉛ハンダの使用を推奨します。
・Sn+Ag+Cu（錫+銀+銅）
・Sn+Cu（錫+銅）
・Sn+Zn+Bi（錫+亜鉛+ビスマス）
注意：
無鉛ハンダの融点温度は通常の鉛入りハンダに比べ30〜40℃
程度高くなっていますので、それぞれのハンダに合ったハンダ
ごてをご使用ください。
All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.
Among some types of lead free solder currently available,
it is recommended to use one of the following types for the
repair work.
• Sn + Ag + Cu (tin + silver + copper)
• Sn + Cu (tin + copper)
• Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
As the melting point temperature of the lead free solder
is about 30°C to 40°C (50°F to 70°F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.
About lead free solder / 無鉛ハンダについて
WARNING: Laser Safety
This product contains a laser beam component. This component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be
used during servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from
the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.

DVD-S1700
3
DVD-S1700
Laser Emitting conditions:
1) When the Top Cover is removed, and the STANDBY/ON SW is turned to the "ON" position, the laser component will emit
a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the
lens of the laser pick-up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser
emissions.
2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory
prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this
manual. Adjustment of this control can increase the laser emission level from the device.
Laser Diode Properties
Type: Semiconductor laser GaAlAs
Wave length: 650 nm (DVD)
790 nm (VCD/CD)
Output Power: 1.45 mW (DVD)
1.13 mW (VCD/CD)
Beam divergence: 60 degrees
VARO! : AVATTAESSA JA SUOJALUKITUS
OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASER-
SÄTEILYLLE. ÄLÄ KATSO
SÄTEESEEN.
VARNING! : OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.

DVD-S1700
4
DVD-S1700
■PREVENTION OF ELECTROSTATIC DISCHARGE
This product incorporates copyright pro-
tection technology that is protected by
method claims of certain U.S. patents and
other intellectual property rights owned by
Macrovision Corporation and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation. Reverse engineer-
ing or disassembly is prohibited.
The laser diode in the DVD mechanism may be damaged due to static electricity from clothes or the human body. Use caution
to prevent electrostatic damage when servicing or handling the DVD-mechanism.
1. Grounding for electrostatic damage prevention
Some devices, such as the DVD player, use an optical pickup (laser diode) that will be damaged by static electricity in the
working environment. Only attempt service after ensuring that all grounding procedures have been completed.
1. Worktable grounding
Put a grounded conductive material (sheet) or iron sheet on the area where the optical pickup is placed.
2. Human body grounding
Use an anti-static wrist strap to discharge the static electricity from your body.
2. Handling Precautions for DVD mechanism
1. Handle the DVD mechanism gently, as it is an extremely high-precision assembly.
2. The flexible cable lines may break if an excessive force is applied to it. Use caution when handling the cable.
3. The semi-fixed resistor for laser power adjustment should not be adjusted. Do not turn the resistor.
■LOCALE MANAGEMENT INFORMATION
Locale Management Information : This DVD player is designed and manufactured to respond to the Locale
Management Information that is recorded on a DVD disc. If the Locale number described on the DVD disc does not
correspond to the Locale number of this DVD player, this DVD player cannot play this disc.
Warning for power supply
The primary side of the power supply carries live mains voltage when the player is connected to the mains even when
the player is switched off !
This primary area is not shielded so it is possible to touch copper tracks and/or components when servicing the player.
Service personnel have to take precautions to prevent touching this area or components in this area.
Note:
The screws on the DVD mechanism may never be touched, removed or re-adjusted.
Handle the DVD mechanism with care when the unit has to be exchanged!
The DVD mechanism is very sensitive for dropping or giving shocks.
1M-ohms
Conductive material
(sheet) or steel sheet
Anti-static wrist strap
1
4
2
2
2
5
5
5
4
3
6

DVD-S1700
5
DVD-S1700
■FRONT PANEL
U, T, K, A, G, L, J models
■REAR PANELS
U model
T model
K model

DVD-S1700
6
DVD-S1700
A model
G model
J model
L model

DVD-S1700
7
“HDMI”, the “HDMI” logo and “High Definition
Multimedia Interface” are trademarks or regis-
tered trademark of HDMI Licensing LLC.
HDMI、HDMIロゴおよびHigh - D efi n iti o n
MultimediaInterfaceは、HDMILicensingLLCの
商標または、登録商標です。
“DCDi” is a trademark of Faroudja, a division of
Genesis Microchip, Inc.
DCDiは、GenesisMicrochipInc.の事業部門である
Faroudjaの商標です。
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
DivX、DivX Certified、および関連するロゴは、
DivX,Inc.の商標です。これらの商標は、DivX,Inc.
の使用許諾を得て使用しています。
“DTS” and “DTS Digital Surround” are regis-
tered trademarks of Digital Theater Systems,
Inc.
DTSおよびDTSDigitalSurroundはデジタルシア
ターシステムズの登録商標です。
■REMOTE CONTROL PANEL
■SPECIFICATIONS / 参考仕様
GENERAL / 一般
Dimensions (W x H x D) / 435 x 87 x 284.5 mm
寸法（幅 x 高さ x  奥行き） (17-1/8" x 3-7/16" x 11-3/16")
Weight / 質量 3.3 Kg (7 lbs. 4 oz)
Finish / 仕上げ Gold color (K, J models)
Black color (U, A, G models)
Titanium color (T, G, L models)
Power supply / 電源電圧 AC 120 V, 60 Hz (U model)
AC 100-240 V, 50 Hz (T model)
AC 100-240 V, 50/60 Hz
(K, A, L models)
AC 230 V, 50 Hz (G model)
AC 100 V, 50/60 Hz (J model)
Power consumption / 消費電力 Approx. 21 W
Standby power consumption / < 0.5 W
待機時消費電力
ACCESSORIES / 付属品
Remote control x 1
Battery (AAA, R03, UM-4) x 2
Power cable (2 m) x 1 (U, T, A, G, L, J models)
Power cable (2 m) x 2 (K model)
Video pin cable (1 m) x 1
Audio pin cable (1 m) x 1
* Specifications are subject to change without prior notice.
※参考仕様および外観は予告なく変更されることがあります。
U ........ U.S.A. model T ........ Chinese model
K ........ Korean model A ........ Australian model
G ........ European model L ........ Singapore model
J ......... Japanese model
Manufactured under license from Dolby Labora-
tories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
ドルビーラボラトリーズからの実施権により製造され
ています。「ドルビー」およびダブルD記号は、ドル
ビーラボラトリーズの商標です。
• DIMENSIONS
Unit: mm (inch)
単位：mm（インチ）
PLAYBACK SYSTEM / 対応ディスク
DVD-video
DVD-audio
DVD-R, DVD-RW
DVD+R, DVD+RW, DVD+R DL
Video CD, SVCD
SA-CD multi-channel and SA-CD stereo
CD
Picture CD
CD-R, CD-RW
VIDEO PERFORMANCE / ビデオ部
Video (CVBS) output 1 Vpp into 75 ohms
S-video output Y: 1 Vpp into 75 ohms
C: 0.3 Vpp into 75 ohms
D1/D2 output (J model) Y: 1 Vpp into 75 ohms
PB/CB, PR/CR: 0.7 Vpp into 75 ohms
Component video output (U, T, K, A, G, L models)
Y: 1 Vpp into 75 ohms
PB/CB, PR/CR: 0.7 Vpp into 75 ohms
RGB (SCART) output (G model)
0.7 Vpp into 75 ohms
Black level shift (U model)
On/Off
AUDIO FORMAT / オーディオフォーマット
Digital Dolby Digital/DTS/MPEG
Compressed Digital
PCM 16, 20, 24 bits
fs 44.1, 48, 88.2, 96 kHz
MP3 (ISO 9660) 32 kbps to 320 kbps
fs 16, 22.05, 24, 32, 44.1, 48 kHz
WMA 64 kbps to 320 kbps
mono, stereo
Full decoding of Dolby Digital and DTS multi-channel sound
Analog stereo sound
Dolby surround compatible downmix from Dolby Digital multi-
channel sound
AUDIO PERFORMANCE / オーディオ特性
DA converter 24 bits, 192 kHz
Signal to noise (1 kHz) 115 dB
Dynamic range (1 kHz) 105 dB
DVD fs 96 kHz 2 Hz to 44 kHz
fs 48 kHz 2 Hz to 22 kHz
SVCD fs 48 kHz 2 Hz to 22 kHz
fs 44.1 kHz 2 Hz to 20 kHz
CD/VCD fs 44.1 kHz 2 Hz to 20 kHz
Distortion and noise (1 kHz) 0.002 %
TV STANDARD (PAL: 50 Hz) (NTSC: 60 Hz)
Number of lines 625 525
Playback Multistandard (PAL/NTSC)
CONNECTIONS / 接続端子
Video output Cinch (yellow) x 1
S-video output Mini DIN, 4 pins x 1
D1/D2 output (J model) 1
Component video output
Y output Cinch (green) x 1
PB/CBoutput Cinch (blue) x 1
PR/CRoutput Cinch (red) x 1
SCART (G model) Euroconnector x 1
Digital output Coaxial x 1
Optical x 1
IEC60958 for CDDA/LPCM,
IEC61937 for MPEG 1/2,
Dolby Digital and DTS
HDMI Type A x 1
Audio output
2 channel analog output
MIXED 2CH L/R Cinch (white/red) x 1 pair
Multi channel analog output
FRONT L/R Cinch (white/red) x 1 pair
SURROUND L/R Cinch (white/red) x 1 pair
CENTER Cinch (black) x 1
SUBWOOFER Cinch (black) x 1
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corpo-
ration and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation. Re-
verse engineering or disassembly is prohibited.
本製品は、著作権保護技術を採用しており、マクロビジョン社及びその
他の著作権利者が保有する米国特許及びその他の知的財産権によって保
護されています。この著作権保護技術の使用は、マクロビジョン社の許
可が必要で、またマクロビジョン社の特別な許可がない限り家庭用及び
その他の一部の視聴用の使用に制限されています。分解したり、改造す
ることも禁じられています。
435 (17-1/8")
87 (3-7/16") 70 (2-3/4") 273.5 (10-3/4")
17
(11/16")
4
(3/16") 284.5 (11-3/16")
7
(1/4")

DVD-S1700
8
NO DISC
UNKNOWN DISC
When no disc is loaded in the tray. / ディスクがトレイにセットされていない場合。
When a disc which cannot be played or recognized is loaded in the tray. /
再生できない、または認識できないディスクがトレイにセットされている場合。
■INTERNAL VIEW
123 4
56
1
2
3
4
5
6
POWER SUPPLY UNIT
DVD MECHANISM UNIT
MAIN (1) P.C.B.
MAIN (4) P.C.B. (G model)
MAIN (2) P.C.B.
MAIN (3) P.C.B.

■ERROR MESSAGE / エラーメッセージ
■TRADE MODE / トレードモード
In the TRADE mode, the tray open/close function is stopped
temporarily.
• Setting TRADE mode
1. Connect the power cable of the main unit to the AC
outlet.
2. Press the “STANDBY/ON”key of the main unit or re-
mote controller to turn on the power.
3. Press the “OPEN/CLOSE”key of the main unit to open
the tray.
4. Place a disc in the tray and open the “OPEN/CLOSE”
key of the main unit to close the tray.
5. While pressing the “SKIP+/SEARCH+”key of the
main unit and press the “STOP”key for 3 seconds
or longer.
6. When the TRADE mode is set, [TRADE ON] is dis-
played which then returns to the normal display.
Note: Even after the TRADE mode is set, all func-
tions remain the same as normal except the
“OPEN/ CLOSE”key.
Press the “OPEN/CLOSE”key, and [TRAY
LOCKED] is displayed.
• Canceling TRADE mode
1. With a disc set in the tray, while pressing the “SKIP+/
SEARCH+”key of the main unit and press the “STOP”
key for 3 seconds or longer.
2. When the TRADE mode is cancelled, [TRADE OFF]
is displayed which then returns to the normal dis-
play.
トレードモードは、トレイのOPEN/CLOSE機能を一時的に停止
する機能です。
・ トレードモードの起動
1. 本機の電源コードをACコンセントに接続します。
2. 本機またはリモコンのSTANDBY/ONキーを押し、電源
を入れます。
3. 本機のOPEN/CLOSEキーを押し、トレイを開きます。
4. トレイにディスクをセットし、本機のOPEN/CLOSE
キーを押しトレイを閉じます。
5. 本機のSKIP+/SEARCH+キーを押しながら次に
STOPキーを3秒間以上押し続けます。
6. トレードモードが起動し「TRADEON」と表示した後、通常
の表示に戻ります。
注： トレードモード起動後、OPEN/CLOSEキー以
外の操作は通常通り行うことができます。
OPEN/CLOSEキーを押すと「TRAYLOCKED」
と表示されます。
・ トレードモードの解除
1. トレイにディスクがセットされている状態で、本機の
SKIP+/SEARCH+キーを押しながら次にSTOPキー
を3秒間以上押し続けます。
2. トレードモードが解除され「TRADEOFF」と表示した後、
通常の表示に戻ります。
Display / 表示 Cause / 原因
■TROUBLESHOOTING / トラブルシュート
・ HDMIリセット
本機とTVモニターをHDMIケーブルで接続しても映像が表示
されない場合
1. 本機のSTOPキーまたは、リモコンのSTOPキーを2
回押します。
2. 本機のSTOPキーを押しながらPLAY/PAUSEキーを
3秒間以上押し続けます。
3.本機のディスプレイに「HDMIRESET」と表示した後、通
常の表示に戻ります。
・ ビデオリセット
本機とTVモニターを映像ピンケーブルなどで接続しても映像
が表示されない、または映像が正しく表示されない場合
1. 本機のEJECTキーを押してトレイを開きます。
2. リモコンのCLEARキーを押します。
3. リモコンの2、5、8、0キーを押します。
4. リモコンのAUDIOキーを押します。
• HDMI Reset
When no picture is displayed even though the main unit
and TV monitor are connected with the HDMI cable
1. Press the “STOP”key of the main unit or on the re-
mote control twice.
2. While pressing the “STOP”key of the main unit, press
the “PLAY/PAUSE”key for 3 seconds or longer.
3. [HDMI RESE] is displayed of the main unit which then
returns to the normal display.
• VIDEO Reset
When no picture is displayed or picture is displayed but
not properly even though the main unit and TV monitor
are connected with the video pin cable or the like
1. Press the “EJECT”key to open the tray.
2. Press the “CLEAR”key on the remote control.
3. Press the “2”, “5”, “8”and “0”keys on the remote con-
trol.
4. Press the “AUDIO”key on the remote control.
"STOP" key"EJECT" keyTra y
"PLAY/PAUSE" key
Main unit / 本機
Remote control / リモコン

DVD-S1700
9
Fig. 1
■DISASSEMBLY PROCEDURES/分解手順
（番号順に部品を取り外してください。）
AC電源コンセントから、電源コードを抜いてください。
1. トップカバーの外し方
a. 1のネジ6本を外します。（Fig.1）
b. トップカバーの後ろを持ち上げ、後方へ取り外します。（Fig.1）
(Remove parts in disassembly order as numbered.)
Disconnect the power cable from the AC outlet.
1. Removal of Top Cabinet
a. Remove 6 screws (1). (Fig. 1)
b. Lift up the rear side of the top cover, then remove rear-
ward. (Fig. 1)
1
Top cover
トップカバー
Front panel ass'y
フロントパネルASS'Y
Front panel ass'y
フロントパネルASS'Y
Front panel ass'y
フロントパネルASS'Y
Tray lid
トレイリッド
Hook
フック
Hook
フック
Hook
フック
Hook
フック
DVD mechanism unit
DVDメカユニット
1
1
1
2
3
4
5
5
Front Front
DVD mechanism unit
DVDメカユニット
2. Removal of DVD Mechanism Unit
a. Eject the tray. (See “How to manually eject the tray”.)
b. Remove the tray lid and close the tray. (Fig. 1)
c. Remove 2 screws (2). (Fig. 1)
d. Solder the lands in the P.C.B. of the DVD mechanism
unit with the anti-static soldering iron. (Fig. 2)
2. DVDメカユニットの外し方
a. トレイを開きます。（手動でトレイを開く方法を参照）
b. トレイリッドを外し、トレイを閉じます。（Fig.1）
c. 2のネジ2本を外します。（Fig.1）
d. DVDメカユニットの基板上の端子間を静電気対策はんだこて
を使用してショートします。（Fig.2）
注意
・ 修理終了時は、先にカード電線をCN11に接続し、次に静電
気対策はんだこてを使用してショート箇所からはんだを除去
します。
Note
• After you have finished repairing , connect the
flexible flat cable to CN11 in advance and then re-
move the solder from the short-circuit location
with the anti-static soldering iron.
Solder
CN11
CN12
CN13
CX41
MAIN (1) P.C.B.
DVD mechanism unit
DVDメカユニット
3. Removal of Front Panel Ass’y
a. Remove 3 screws (3) and 4 screws (4). (Fig. 1)
b. Remove 2 screws (5). (Fig. 1)
c. Remove CX41. (Fig. 2)
d. Remove 2 hooks and then remove the front panel ass’y
forward. (Fig. 1)
3. フロントパネルASSYの外し方
a. 3のネジ3本、4のネジ4本を外します。（Fig.1）
b. 5のネジ2本を外します。（Fig.1）
c. CX41を外します。（Fig.2）
d. フック2箇所を外し、フロントパネルASSYを前方へ取り外
します。（Fig.1）
Fig. 2
• How to manually eject the tray / 手動でトレイを開く方法
a. Turn the unit bottom up.
b. Turn the loading gear in the direction indicated with a
flatblade screwdriver until the tray is ejected.
c. Gently pull the tray out.
a. 本機を上下反転します。
b. トレイが出てくるまで、マイナスドライバーでローディングギ
アを図に示す矢印の方向に回転します。
c. トレイをそっと引き出します。
e. CN11、CN12、CN13を外します。（Fig.2）
f. DVDメカユニットの後ろを持ち上げ、フック2箇所を外し、
後方へ取り外します。（Fig.1）
e. Remove CN11, CN12 and CN13. (Fig. 2)
f. Lift up the rear side of the DVD mechanism unit, then
remove 2 hooks and remove rearward. (Fig. 1)
Tra y
トレイ
Loading gear
ローディングギア
Tra y
トレイ
Flatblade screwdriver
マイナスドライバー

DVD-S1700
10
SG1
SG2
SG3
SG4
SG5
SG6
SG7
SG8
SG9
SG10
SG11
SG12
SG13
SG14
SG15
SG16
SG17
SG18
SG19
SG20
SG21
SG22
SG23
SG24
SG25
SG26
SG27
SG28
SG29
SG30
SG31
SG32
SG33
SG34
SG35
GR14
14G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR13
13G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR12
12G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR11
11G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR10
10G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR9
9G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR8
8G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR7
7G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR6
6G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR5
5G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR4
4G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR3
3G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR2
2G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
GR1
1G
●ANODE CONNECTION
■DISPLAY DATA
●F401 : HCA14SM16 (AAX80850)
●PIN CONNECTION
●GRID ASSIGNMENT
Pin No.
Connection
25
NX
Note : 1) F1, F2 ..... Filament pin 2) NP ..... No pin 3) NC ..... No connection 4) NX ..... No extended pin
3G 2G4G5G6G7G8G9G
1G
(2G-14G)
10G11G
12345
678910
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31 32 33 34 35
12G13G14G
j1
PATTERN AREA
24
NX
23
NX
22
NX
21
NX
20
NX
19
NX
18
NX
17
NX
16
1G
15
NC
14
GR1
13
V
DD
12
DIN
11
CLKB
10
CSB
9
RSTB
8
OSCO
7
OSCI
6
V
EE
5
GND
4
NP
3
NP
2
F1
1
F1
Pin No.
Connection
50
F2
49
F2
48
NP
47
NP
46
NX
45
NX
44
NX
43
NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX NX
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26

DVD-S1700
11
DVD-S1700
MEMO
MEMO

DVD-S1700
12
DVD-S1700
■IC DATA
TRAY
IR-RC
Receiver
Front Panel
Concentrator SPI/I2C/GPIO/DDC
MICROPROCESSOR
SERVO
vvvvv
v
v
v
AFE
ADP DSP
MCU
VPU
PLL
27 MHz
8/16 Mbits
NOR
Flash
RESET
32/64/128
Mbits
SDRAM
Vaddis
778
SPINDLE
SLED
OPU
Disc loader
RF amp
Servo amp
S/PDIF
Audio
ADC
Stereo
Mics
2 to 8
Speakers
TV
Monitor
DAC
IC11: ZR36778 (MAIN P.C.B.)
MPEG decoder

DVD-S1700
13
DVD-S1700
1
2
3
4,5
6
7
8
9
10
11
12
13
14
15
16
17
18-19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
SSCRXD
GPCI/O[17]
PM[15]
MEMCS[1]#
GPCI/O[18]
VDDP
MEMAD
[15,16]
SYSIND[1,0]
MEMAD[14]
GCLKSEL
MEMAD[13]
FCUIF[29]
MEMAD[12]
PLLCFGA
MEMDA[15]
FCUIF[28]
MEMAD[11]
PLLCFGP
MEMDA[7]
FCUIF[9]
GNDP
MEMAD[10]
FCUIF[20]
MEMDA[14]
FCUIF[27]
MEMAD[9]
FCUIF[19]
MEMDA[6]
FCUIF[8]
MEMAD[8]
FCUIF[18]
MEMDA[13,5]
FCUIF[26,7]
MEMAD[20]
MEMCS[2]#
GPCI/O[19]
VDDP
MEMDA[12]
FCUIF[25]
MEMWR#
FCUIF[0]
MEMDA[4]
FCUIF[6]
VDDC
MEMDA[11]
FCUIF[24]
MEMDA[3]
FCUIF[5]
MEMAD[19]
PLLSEL
GNDC
MEMDA[10]
FCUIF[23]
MEMAD[18]
GNDP
MEMDA[2]
FCUIF[4]
MEMAD[17]
MEMDA[9]
FCUIF[22]
MEMAD[7]
FCUIF[17]
MEMDA[1]
FCUIF[3]
MEMAD[6]
I
I/O
O
O
I/O
S
O
I
O
I
O
O
O
I
I/O
I/O
O
I
I/O
I/O
S
O
O
I/O
I/O
O
O
I/O
I/O
O
O
I/O
I/O
O
O
I/O
S
I/O
I/O
O
O
I/O
O
S
I/O
I/O
I/O
I/O
O
I
S
I/O
I/O
O
S
I/O
I/O
O
I/O
I/O
O
O
I/O
I/O
O
SSC data input
General purpose I/O, monitored/controlled by the microprocessor or DSP or FCU SW
Probe mux data output
PNVM/SRAM chip select (active low) output
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
3.3 V digital periphery power supply
PNVM/SRAM address bus outputs
General purpose system configuration indication input / Level sampled during RESET
PNVM/SRAM address bus output
GCLKPOUT or GCLKA function selection / Level sampled during RESET
PNVM/SRAM address bus output
Flash card interface unit output signal
PNVM/SRAM address bus output
Audio PLL configuration input / Level sampled during RESET / In normal operation the pin must be low during RESET
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM address bus output
Process PLL configuration input / Level sampled during RESET / In normal operation the pin must be low during RESET
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signals
Digital periphery ground of 3.3 V supply
PNVM/SRAM address bus output
Flash card interface unit output signal
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM address bus outputs
Flash card interface unit output signal
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signals
PNVM/SRAM address bus outputs
Flash card interface unit output signal
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signals
PNVM/SRAM address bus outputs
PNVM/SRAM chip select (active low) output
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
3.3 V digital periphery power supply
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM write enable (active low) output
Flash card interface unit output signal
PNVM/SRAM bi-directional data bus
Flash card interface unit output signal
1.8 V digital core power supply
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signals
PNVM/SRAM address bus outputs
PLL frequency selection -108 MHz (low) or 135 MHz (high) / Level sampled during RESET
Digital core ground of 1.8 V supply
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM address bus output
Digital periphery ground of 3.3 V supply
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signals
PNVM/SRAM address bus output
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM address bus outputs
Flash card interface unit output signal
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signals
PNVM/SRAM address bus outputs
Pin Functions Direction DescriptionNo.

DVD-S1700
14
DVD-S1700
39
40
41
42
43
44
45-46
47
48
49
50
51
52
53-57
58
59-61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84-86
87
88-90
91
FCUIF[16]
MEMDA[8]
FCUIF[21]
MEMAD[5]
FCUIF[15]
VDDP
MEMDA[0]
FCUIF[2]
MEMAD[4]
FCUIF[14]
MEMRD#
FCUIF[1]
MEMAD[3, 2]
FCUIF[13, 12]
MEMCS[0]#
MEMAD[1]
FCUIF[11]
BOOTSEL[2]
MEMAD[0]
FCUIF[10]
BOOTSEL[1]
GNDP
VDD-IP
VDDP
RAMADD
[4, 3, 5, 2, 6]
VDDP
RAMADD
[1, 7, 0]
GNDP
RAMADD[8]
VDDC
RAMADD[10]
GNDC
RAMADD[9]
VDDP
RAMADD[11]
RAMCS[0]#
RAMBA[1]
RAMBA[0]
GNDP
RAMCS[1]#
RAMRAS#
RAMCAS#
VDDP
RAMWE#
RAMDQM
GNDPCLK
PCLK
VDDPCLK
RAMDAT[8]
GNDP
RAMDAT
[7, 9, 6]
VDDP
RAMDAT
[10, 5, 11]
GNDP
O
I/O
I/O
O
O
S
I/O
O
I/O
O
O
I/O
O
O
O
O
O
I
O
O
I
S
S
S
O
S
O
S
O
S
O
S
O
S
O
O
O
O
S
O
O
O
S
O
O
S
O
S
I/O
S
I/O
S
I/O
S
Flash card interface unit output signal
PNVM/SRAM bi-directional data bus
Flash card interface unit I/O signal
PNVM/SRAM address bus outputs
Flash card interface unit output signal
3.3 V digital periphery power supply
PNVM/SRAM bi-directional data bus
Flash card interface unit output signal
PNVM/SRAM address bus outputs
Flash card interface unit output signal
PNVM/SRAM read enable (active low) output
Flash card interface unit I/O signal
PNVM/SRAM address bus outputs
Flash card interface unit output signal
PNVM/SRAM chip select (active low) output
PNVM/SRAM address bus outputs
Flash card interface unit output signals
Microprocessor SW boot (and execute) source selection:
(high, high) - For production testing;
(high, low) - Flash+SRAM (for debug monitor);
(low, high) - First debug UART
(low, low) - Flash (low) or Level sampled during RESET
PNVM/SRAM address bus outputs
Flash card interface unit output signals
Microprocessor SW boot (and execute) source selection:
(high, high) - For production testing;
(high, low) - Flash+SRAM (for debug monitor);
(low, high) - First debug UART
(low, low) - Flash (low) or Level sampled during RESET
Digital periphery ground of 3.3 V supply
3.3 V periphery reference voltage
3.3 V digital periphery power supply
SDRAM address bus output
3.3 V digital periphery power supply
SDRAM address bus output
Digital periphery ground of 3.3 V supply
SDRAM address bus output
1.8 V digital core power supply
SDRAM address bus output
Digital core ground of 1.8 V supply
SDRAM address bus output
3.3 V digital periphery power supply
SDRAM address bus output
SDRAM chip select (active low)
SDRAM bank select output
SDRAM bank select output
Digital periphery ground of 3.3 V supply
SDRAM chip select (active low) output
SDRAM row select (active low) output
SDRAM column select (active low) output
3.3 V digital periphery power supply
SDRAM write enable (active low) output
SDRAM data masking (active high) output
Digital ground of filtered 3.3 V supply for PCLK
SDRAM clock output (same as internal processing clock)
3.3 V filtered digital power supply for PCLK
SDRAM bi-directional data bus
Digital periphery ground of 3.3 V supply
SDRAM bi-directional data bus
3.3 V digital periphery power supply
SDRAM bi-directional data bus
Digital periphery ground of 3.3 V supply
Pin Functions Direction Description
No.

DVD-S1700
15
DVD-S1700
92
93
94
95
96
97
98-100
101
102-104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
RAMDAT[4]
VDDC
RAMDAT[12]
GNDC
RAMDAT[3]
VDDP
RAMDAT
[13, 2, 14]
GNDP
RAMDAT
[1, 15, 0]
VDDP
GPCI/O[20]
CPUNMI
SDATA[0]
PM[0]
GNDP
ICGPCI/O[0]
AOUT[3]
SDATA[1]
PM[1]
IDGPCI/O[0]
RAMCKE
SDATA[2]
PM[2]
S/PDIFOUT
SDATA[3]
PM[3]
AOUT[2]
GPCI/O[21]
SDATA[4]
PM[4]
AOUT[1]
GPCI/O[22]
PM[5]
AOUT[0]
SDATA[6]
PM[6]
GPAI/O
AOUT[3]
IDGPCI/O[0]
PM[7]
ALRCLK
ABCLK
GNDP-A2
AMCLK
VDDP-A2
AIN
GPCI/O[23]
PM[8]
GNDC
VSYNC#
HDFI
GPI/O[24]
DACTEST[9]
PM[9]
VDDC
HSYNC#
HDHS
GPCI/O[25]
GNDP
VCLKx2
I/O
S
I/O
S
I/O
S
I/O
S
I/O
S
I/O
I
I
O
S
I/O
O
I
O
I/O
O
I
O
O
I
O
O
I/O
I
O
O
I/O
O
O
I
O
I/O
O
I/O
O
O
O
S
I/O
S
I
I/O
O
S
O
I
I/O
I
O
S
O
I
I/O
S
O
SDRAM bi-directional data bus
1.8 V digital core power supply
SDRAM bi-directional data bus
Digital core ground of 1.8 V supply
SDRAM bi-directional data bus
3.3 V digital periphery power supply
SDRAM bi-directional data bus
Digital periphery ground of 3.3 V supply
SDRAM bi-directional data bus
3.3 V digital periphery power supply
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Microprocessor non-maskable interrupt input
SERVO channel sample data input for AFE by-pass
Probe mux data output
Digital periphery ground of 3.3 V supply
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
Serial output of digital stereo audio
SERVO channel sample data input for AFE by-pass
Probe mux data output
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Clock enable signal to the SDRAM (for power down)
SERVO channel sample data input for AFE by-pass
Probe mux data output
S/PDIF transmitter output for digital coded or reconstructed audio data
SERVO channel sample data input for AFE by-pass
Probe mux data output
Serial outputs of digital stereo audio
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
SERVO channel sample data inputs for AFE by-pass
Probe mux data outputs
Serial output of digital stereo audio
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Probe mux data outputs
Serial output of digital stereo audio
SERVO channel sample data input for AFE by-pass
Probe mux data outputs
General purpose I/O, monitored/controlled by the ADP SW
Serial output of digital stereo audio
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Probe mux data output
Digital audio left/right select output for the audio port / Square wave, at the sampling frequency / Programmable polarity
Digital audio bit-clock output / Data on AOUT and AIN is output or latched, respectively, with the rising or
falling (programmable) edge of this clock
Digital ground filtered 3.3 V supply for AMCLK
Audio master clock I/O / 128, 192, 256 or 384 times the sampling frequency (programmable)
3.3 V filtered digital power supply for AMCLK
Serial input of digital stereo audio
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Probe mux data output
Digital core ground of 1.8 V supply
SD digital video vertical sync output signal
HD digital video field index input signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
DACs test input
Probe mux data output
1.8 V digital core power supply
SD digital video horizontal sync output signal
HD digital video horizontal sync input signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Digital periphery ground of 3.3 V supply
Digital video clock output / 27,000 (for SD interlaced), 54,000 (SD progressive) or 135,000 (for HD) MHz
Pin Functions Direction DescriptionNo.

DVD-S1700
16
DVD-S1700
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
COSYNC
ICGPCI/O[1]
VDDP
VID[7]
GPCI/O[26]
VID[6]
ICGPCI/O[2]
VID[5]
IDGPCI[1]
GNDP
VID[4]
GPCI/O[27]
VID[3]
GPCI/O[28]
SERVOCLK
VID[2]
GPCI/O[29]
SSEL[0]
VDDP
VID[1]
GPCI/O[30]
SSEL[1]
VID[0]
ICGPCI/O[3]
GNDP
GNDA
RESET#
VDDA
XO
GCLKP
GCLKA
GPCI/O[31]
GCLKPOUT
VDDP
ICGPCI/O[4]
S/PDIFIN[0]
GPCI/O[33]
ICGPCI/O[5]
S/PDIFIN[1]
GPCI/O[34]
IDGPCI/O[3]
FCUIF[33]
GNDP
DUPRD0
GPCI/O[35]
DUPTD0
GPCI/O[36]
VDD-IP
DUPRD1
GPCI/O[37]
DUPTD1
GPCI/O[38]
GNDDACD
CVBS/G/Y
(DAC A)
CVBS/C
(DAC D)
O
I/O
S
O
I/O
O
I/O
O
I/O
S
O
I/O
O
I/O
O
O
I/O
O
S
O
I/O
O
O
I/O
S
S
ID
S
AO
ID
ID
I/O
O
S
I/O
I
I/O
I/O
I
I/O
I/O
I
S
I
I/O
O
I/O
S
I
I/O
O
I/O
S
AO
AO
Composite sync output / Active only when component analog output is selected
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
3.3 V digital periphery power supply
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Digital periphery ground of 3.3 V supply
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
SERVO channel clock output for AFE by-pass
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
SERVO channel select output for AFE by-pass
3.3 V digital periphery power supply
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
SERVO channel output for AFE by-pass
Digital 4: 2: 2 video luma/chroma output, interleaved U, Y V Y
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
Digital periphery ground of 3.3 V supply
Ground plane of internal PLL circuit
Reset input (active low)
1.8 V power supply for internal PLL circuit
Output to a crystal that is connected to GCLKP
If a crystal is not used at GCLKP, XO must be left not connected.
27.000MHz clock or crystal input for main processing clock generation.
27.000MHz clock input for audio master clock generation.
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
GCLKP output
3.3 V digital periphery power supply
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
S/PDIF receiver input for digital coded or reconstructed audio data
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
S/PDIF receiver input for digital coded or reconstructed audio data
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Flash card interface unit input signal
Digital periphery ground of 3.3 V supply
First debug UART data input
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
First debug UART data output
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
3.3 V periphery reference voltage
Second debug UART data output
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Second debug UART data output
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Ground for the video DACs 3.3 V analog power supply
When the Vaddis 778 outputs composite (SCART or non-SCART) video, this line is CVBS output
When the Vaddis 778 outputs RGB, this line is the Green output
When the Vaddis 778 outputs YUV, this line is the Y output
When the other Vaddis 778 output are not SCART video, the output on this line can be either CVBS or C / the
selection is independent of the specific selection of the other three DACs
Pin Functions Direction DescriptionNo.

DVD-S1700
17
DVD-S1700
Pin Functions Direction DescriptionNo.
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178-183
184,185
186
187
188
189
190
191
192
193
194
195
196
197
198
VDDDAC
Y/R/V
(DAC B)
C/B/U
(DAC C)
RSET
GNDDACP
GNDDABS2
GNDDACPS
DACDRIVE[0]
VDDDACS
DACDRIVE[1]
GNDDACDS
VDDAFERF
RFINP
RFINN
GNDAFERF
VDDAFES
ADCIN[7]
ADCIN[6]
ADCIN[5-0]
VBIASS[0, 1]
GNDAFES
PWMACT[0]
GPCI/O[39]
DVDDAT[0]
NRZDATA
PWMACT[1]
GPCI/O[40]
DVDDAT[1]
NRZCLK
PWMCO[0]
GPCI/O[41]
DVDDAT[2]
NRZLOCK
GNDC
PWMCO[1]
GPCI/O[42]
DVDDAT[3]
NRZDFCT
VDDC
PWMCO[2]
GPCI/O[43]
FCUIF[34]
DVDDAT[4]
PWMCO[3]
GPCI[44]
FCUIF[35]
IDGPCI/O[2]
DVDDAT[5]
GNDPWMS
PWMCO[4]
GPCI/O[45]
DVDDAT[6]
VDDPWMS
PWMCO[5]
GPCI/O[46]
FCUIF[36]
DVDDAT[7]
S
AO
AO
AI
S
S
S
AO
S
AO
S
S
AI
AI
S
S
AI
AI
AI
AI
S
O
I/O
I
I
O
I/O
I
I
O
I/O
I
I
S
O
I/O
I
I
S
O
I/O
O
I
O
I/O
I/O
I/O
I
S
O
I/O
I
S
O
I/O
I/O
I
When the Vaddis 778 outputs composite SCART video, this line is the Y output
3.3 V analog power supply for the video DACs
When the Vaddis 778 outputs composite non-SCART video, this line is Y output
When the Vaddis 778 output RGB, this line is the Red output
When the Vaddis 778 outputs YUV, this line is the V output
When the Vaddis 778 outputs composite SCART video, this line is the C output
When the Vaddis 778 outputs composite (SCART or non-SCART) video, this line is C output
When the Vaddis 778 outputs RGB, this line is the Blue output
When the Vaddis 778 outputs YUV, this line is the U output
Resistive load for gain adjustment of the DACs
Ground for the video DACs 3.3 V analog power supply
Common ground for the video and SERVO DACs
Ground for the SERVO DAC 3.3 V analog power
Drive DACs output signal
3.3 V SERVO DACs power supply
Drive DACs output signal
Ground for the SERVO DAC 3.3 V analog power supply
3.3 V analog RF (AFE) power supply
RF positive input signal (differential input) //
RF input signal (single ended)
RF negative input signal (differential input) //
RF reference input signal
Analog RF (AFE) ground of 3.3 V supply
3.3 V analog SERVO (AFE) power supply
SERVO ADC input signal (e.g. from RF amplifier)
SERVO ADC input signal from RF amplifier
SERVO ADC input signal (e.g. from RF amplifier)
Servo analog signal reference voltage inputs
Analog SERVO (AFE) ground of 3.3 V supply
PWM0 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP or FCU SW
AV data input for FE by-pass
NRZ data input for AFE and DRC by-pass
PWM1 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP or FCU SW
AV data input for FE by-pass
NRZ clock input for AFE and DRC by-pass
PWM2 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
AV data input for FE by-pass
NRZ lock input for AFE and DRC by-pass
Digital core ground of 1.8 V supply
PWM3 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
AV data input for FE by-pass
NRZ defect input for AFE and DRC by-pass
1.8 V digital core power supply
PWM4 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Flash card interface unit input signal
AV data input for FE by-pass
PWM5 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Flash card interface unit I/O signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
AV data input for FE by-pass
SERVO PWMs ground of 3.3 V supply
PWM6 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
AV data input for FE by-pass
3.3 V SERVO PWM power supply
PWM7 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
Flash card interface unit I/O signal
AV data input for FE by-pass

DVD-S1700
18
DVD-S1700
Pin Functions Direction DescriptionNo.
199
200
201
202
203
204
205
206
207
208
PWMCO[6]
IDGPCI/O[4]
FCUIF[32]
DVDSTRB
RFDAT[4]
DEFFCT
IDGPCI/O[5]
FCUIF[37]
DVDREQ
ICGPI/O[6]
DVDVALID
GNDP
ICGPI/O[7]
DVDERR
VDDP
SLEDPULSE
IDGPCI/O[6]
FCUIF[30]
DVDSOS
SPIND LEPULSE
IDGPCI/O[7]
FCUIF[31]
SSCCLK
GPCI/O[47]
SSCTXD
GPCI/O[16]
O
I/O
I/O
I
I
I/O
I/O
I/O
O
I/O
I
S
I/O
I
S
I
I/O
I
I
I
I/O
I/O
I/O
I/O
O
I/O
PMW8 output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Flash card interface unit I/O signal
AV data input for FE by-pass
RF channel sample data inputs for AFE by-pass
Disc defect input or output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Flash card interface unit I/O signal
AV data request output for FE by-pass / Programmable polarity
General purpose I/O, monitored/controlled by the microprocessor or DSP or FCU SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
AV data valid input for FE by-pass / Programmable polarity
Digital periphery ground of 3.3 V supply
General purpose I/O, monitored/controlled by the microprocessor or DSP or FCU SW
When input, the pin can be used as general purpose external interrupt to the microprocessor
AV error input for FE by-pass / Programmable polarity
3.3 V digital periphery power supply
Sled optical encoder input
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Flash card interface unit output signal
AV start of sector indication input for FE by-pass / Programmable polarity
Spindle optical encoder input
General purpose I/O, monitored/controlled by the microprocessor or DSP SW
When input, the pin can be used as general purpose external interrupt to the DSP
Flash card interface unit I/O signal
SSC clock input signal
General purpose I/O, monitored/controlled by the microprocessor or DSP or FCU SW
SSC data output signal
General purpose I/O, monitored/controlled by the microprocessor or DSP SW

DVD-S1700
19
DVD-S1700
IC20: SAA7893HLC2 (MAIN P.C.B.)
DSD decoder
SAA7893HL
HOST
INTERFACE
SDRAM
INTERFACE
SAA7893HL
to 64 Mbit
SDRAM
to host
host_sel
sys_clk
27-35 MHz
external PCM
MBL615
to
DSD/PCM
DAC
aud_clk
256/384/512/768*fs
MEMORY
MANAGER
PI-bus
controlkey
HF
data-bus
REGISTER
HOST
INTERFACE
DEMUX
DECRYPTION/
SECTOR
PROCESSOR
PSP-KEY
DECODER
ADCAGC
SACD
AUDIO
INTERFACE
PI-BUS
CONTROL
2, 5 or 6-channel
LOSSLESS
DECODER
SPEAKER SETUP
VOLUME CONTROL
DELAY
8-CHANNEL
DSD2PCM
CONVERSION
SWITCH
MATRIX
FRONT-
END
INTERFACE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
128 127 126 125 124 123 122 121 120
119 118 117 116 115 114 113 112
111
110
109 108 107 106 105 104 103
H_A[1]
H_DQ[15]
H_DQ[14]
GND_IO1
H_DQ[13]
H_DQ[12]
H_DQ[11]
H_DQ[10]
H_DQ[9]
VCC_IO1
H_DQ[8]
H_DQ[7]
H_DQ[6]
H_DQ[5]
H_DQ[4]
H_DQ[3]
GND_IO2
H_procclock
VCC_Core1
GND_Core1
sys_clk
H_DQ[2]
H_DQ[1]
H_CSn
H_DQ[0]
H_RWn
H_WAIT
H_IRQn
aud_clk
PCM_dclk_in
PCM_wclk_in
VDDA
VSSA
biasin
Agcinp
Adcrefl
VCC_IO7
GND_IO7
PCM_CeLf_in
PCM_LeRi_in
PCM_LsRs_in
B_FLAG/SERR
B_SYNC/Sync
B_WCLK/SENB
B_DATA/Be_dat(0)
B_BCLK/SDCLK
UDE_req
Data_req
Be_dat(1) Be_dat(2) Be_dat(3) Be_dat(4) Be_dat(5) Be_dat(6) Be_dat(7)
TRST
TMS
VCC_IO2
TDO
TDI
TCK
H_sel[0] H_sel[1]
D_ADDR[3]
D_DQ[13]
D_DQ[2]
D_DQ[12]
GND_IO5
D_DQ[3]
D_DQ[11]
D_DQ[4]
D_DQ[10]
D_DQ[9]
D_DQ[6]
VCC_IO4
D_DQ[8]
D_DQ[7]
D_LDQM
D_UDQM
D_DQ[5]
D_clk
VCC_Core2
GND_Core2
GND_IO4
D_CASn
D_RASn
D_Wen
D_ADDR[11]
D_ADDR[12]
D_ADDR[9]
VCC_IO3
D_ADDR[13]
D_ADDR[8]
D_ADDR[10]
D_ADDR[7]
D_ADDR[0]
D_ADDR[6]
GND_IO3
D_ADDR[1]
D_ADDR[5]
D_ADDR[2]
D_ADDR[4]
H_A[2] H_A[3] H_A[4] H_A[5] H_A[6] H_A_sel RESETn DSD_PCM_11 DSD_PCM_9 DSD_PCM_10 VCC_IO6 DSD_PCM_8 DSD_PCM_7 DSD_PCM_6 DSD_PCM_5 DSD_PCM_4 GND_IO6 DSD_PCM_3 DSD_PCM_2 DSD_PCM_1 DSD_PCM_0 D_DQ[15] VCC_IO5 D_DQ[0] D_DQ[14] D_DQ[1]

DVD-S1700
20
DVD-S1700
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
H_A[1]
H_DQ[15]
H_DQ[14]
GND_IO1
H_DQ[13]
H_DQ[12]
H_DQ[11]
H_DQ[10]
H_DQ[9]
VCC_IO1
H_DQ[8]
H_DQ[7]
H_DQ[6]
H_DQ[5]
H_DQ[4]
H_DQ[3]
GND_IO2
H_procclock
VCC_Core1
GND_Core1
sys_clk
H_DQ[2]
H_DQ[1]
H_CSn
H_DQ[0]
H_RWn
H_WAIT
H_IRQn
aud_clk
PCM_dclk_in
PCM_wclk_in
VDDA
VSSA
biasin
Agcinp
Adcrefl
VCC_IO7
GND_IO7
PCM_CeLf_in
PCM_LeRi_in
PCM_LsRs_in
B_FLAG/SERR
B_SYNC/Sync
B_WCLK/SENB
B_DATA/Be_dat(0)
B_BCLK/SDCLK
UDE_req
Data_req
Be_dat(1)
Be_dat(2)
Be_dat(3)
Be_dat(4)
Be_dat(5)
Be_dat(6)
Be_dat(7)
TRST
TMS
VCC_IO2
TDO
TDI
TCK
H_sel[0]
H_sel[1]
Address bus
Data bus
Data bus
GND I/O pads
Data bus
Data bus
Data bus
Data bus
Data bus
Vcc_I/O pads
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
GND I/O pads
Host processor EMI interface clock
Core supply voltage
Core ground
System clock
Data bus
Data bus
Host chip select; active LOW
Data bus
Read = 1; Write = 0
Wait signal
Interrupt request; active LOW
DSD audio clock
PCM data clock
PCM word clock
VDD of ADC
VSS of AGC and ADC;
Connected to substrate
Bias current input
AGC positive input signal; HF in
ADC decoupling
VCC I/O pads
GND I/O pads
PCM data center or LFE
PCM data left or right
PCM data left or right surround
I2S-bus flag (EDC flag)
Sector sync or absolute time sync
I2S-bus word clock or UDE data
sense from host
I2S-bus data or LSB data of parallel interface
I2S-bus bit clock
Host request data from front-end;
routed via the SAA7893HL
Data request for UDE
Front-end parallel data interface
Front-end parallel data interface
Front-end parallel data interface
Front-end parallel data interface
Front-end parallel data interface
Front-end parallel data interface
Front-end parallel data interface
Boundary scan reset
Boundary scan mode select
VCC I/O pads
Output
Boundary scan data input
Boundary scan clock
Host select signals: SAD16,
MAD16 and SAD08
Host select signals: SAD16,
MAD16 and SAD08
IN
I/O10
I/O10
GND_IO
I/O10
I/O10
I/O10
I/O10
I/O10
VCC_IO1
I/O10
I/O10
I/O10
I/O10
I/O10
I/O10
GND_IO
IN
VCC_core
GND_core
IN
I/O10
I/O10
IN
I/O10
IN
O10
O10
IN
IN
IN
VDDCO
VSSCO
APIO
APIO
APIO
VCC_IO
GND_IO
IN
IN
IN
IN
IN
IN
IN
IN
IN
O10
IN
IN
IN
IN
IN
IN
IN
IN1
IN1
VCC_IO
O10
IN1
IN
IN
IN
Pin
Symbol Description
Type[1]
Pin.
Symbol Type[1] Description
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
D_ADDR[3]
D_ADDR[4]
D_ADDR[2]
D_ADDR[5]
D_ADDR[1]
GND_IO3
D_ADDR[6]
D_ADDR[0]
D_ADDR[7]
D_ADDR[10]
D_ADDR[8]
D_ADDR[13]
VCC_IO3
D_ADDR[9]
D_ADDR[12]
D_ADDR[11]
D_Wen
D_RASn
D_CASn
GND_IO4
GND_Core2
VCC_Core2
D_clk
D_DQ[5]
D_UDQM
D_LDQM
D_DQ[7]
D_DQ[8]
VCC_IO4
D_DQ[6]
D_DQ[9]
D_DQ[10]
D_DQ[4]
D_DQ[11]
D_DQ[3]
GND_IO5
D_DQ[12]
D_DQ[2]
D_DQ[13]
D_DQ[1]
D_DQ[14]
D_DQ[0]
VCC_IO5
D_DQ[15]
DSD_PCM_0
DSD_PCM_1
DSD_PCM_2
DSD_PCM_3
GND_IO6
DSD_PCM_4
DSD_PCM_5
DSD_PCM_6
DSD_PCM_7
DSD_PCM_8
VCC_IO6
DSD_PCM_10
DSD_PCM_9
DSD_PCM_11
RESETn
H_A_sel
H_A[6]
H_A[5]
H_A[4]
H_A[3]
H_A[2]
O10
O10
O10
O10
O10
GND_IO
O10
O10
O10
O10
O10
O10
VCC_IO
O10
O10
O10
O10
O10
O10
GND_IO
GND_core
VCC_core
O10
I/O10
O10
O10
I/O10
I/O10
VCC_IO
I/O10
I/O10
I/O10
I/O10
I/O10
I/O10
GND_IO
I/O10
I/O10
I/O10
I/O10
I/O10
I/O10
VCC_IO
I/O10
O10
O10
O10
O10
GND_IO
O10
O10
O10
O10
O10
VCC_IO
O10
O10
O10
IN
IN
IN
IN
IN
IN
IN
SDRAM address bus
SDRAM address bus
SDRAM address bus
SDRAM address bus
SDRAM address bus
GND I/O pads
SDRAM address bus
SDRAM address bus
SDRAM address bus
SDRAM address bus
SDRAM address bus
SDRAM address bus
Vcc I/O pads
SDRAM address bus
SDRAM address bus
SDRAM address bus
Read or write
Row address select; active LOW
Column address select; active LOW
GND I/O pads
Core ground
Core supply voltage
Clock signal needed for SDRAM
Data bus
DQ mask enable (upper)
DQ mask enable (lower)
Data bus
Data bus
Vcc I/O pads
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
GND I/O pads
Data bus
Data bus
Data bus
Data bus
Data bus
Data bus
Vcc_IO pads
Data bus
6-channel data output
6-channel data output
6-channel data output
6-channel data output
GND I/O pads
6-channel data output
6-channel data output
6-channel data output
6-channel data output
2-channel data output
VCC I/O pads
2-channel data output
2-channel clock or control
2-channel data output
Asynchronous reset; active LOW
Address select
Address bus
Address bus
Address bus
Address bus
Address bus