Yamaha HTR-5250 User manual

SAFETY INSTRUCTIONS
•Explanation of Graphical Symbols
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO
RAIN OR MOISTURE
11 Power-Cord Protection -Power-supply cords should be
routed so that they are not likely to be walked
on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit
12 Cleaning -The unit should be cleaned only as
recommended by the manufacturer
13 Nonuse Periods -The power cord of the unit should be
unplugged from the outlet when left unused for along
period of time
14 Object and Liquid Entry -Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit
8Ventilation -The unit should be situated so that its
location or position does not interfere with its proper
ventilation For example, the unit should not be situated
on abed, sofa, rug, or similar surface, that may block the
ventilation openings, or placed
in abuilt-in installation,
such as abookcase or cabinet that may impede the flow
of air through the ventilation openings
9Heat -The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat
10 Power Sources -The unit should be connected to a
power supply only of the type described
in the operating
instructions or as marked
on the unit
The exclamation point within an equilateral
triangle is intended to alert you to the presence
01 important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance
The lightning flash with arrowhead symbol,
within an equilateral triangle,
is intended to
alert you to the presence
01 uninsulated
"dangerous voltage" within the product's
enclosure that may be
01 sullicient magnitude
to constitute arisk
01 electric shock to persons
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER-SERVICEABLE
PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
& &
L- -----'
Read Instructions -All the safety and operating
instructions should be read before the unit
is operated
2Retain Instructions -The safety and operating
instructions should be retained for future reference
3Heed Warnings -All warnings
on the unit and in the
operating instructions should
be adhered to
4Follow Instructions -All operating and other instructions
should be followed
5Water and Moisture -The unit should not be used near
water -for example, near abathtub, washbowl, kitchen
sink, laundry tub,
in awet basement, or near aswimming
pool, etc
6Carts and Stands -The unit should be used only with a
cart or stand that
is recommended by the
manufacturer
6A Aunit and cart combination should be
moved with care Quick stops, excessive
force, and uneven surfaces may cause
the unit and cart combination to overturn
15 Damage Requiring Service -The unit should be serviced
by qualified service personnel when
AThe power-supply cord or the plug has been
damaged, or
BObjects have fallen, or liquid has been spilled into the
unit, or
CThe unit has been exposed to rain, or
oThe unit does not appear to operate normally or exhibits
amarked change
in performance, or
EThe unit has been dropped, or the cabinet damaged
16 Servicing -The user should not attempt to service the
unit beyond those means described
in the operating
instructions All other servicing should be referred to
qualified service personnel
17 Power Lines -
An outdoor antenna should be located
away from power lines
18 Grounding or Polarization -Precautions should be taken
so that the grounding or polarization
is not defeated
7Wall or Ceiling Mounting -The unit should be mounted to
awall or ceiling only as recommended by the
manufacturer
CAUTION
SAFETY INSTRUCTIONS
•Explanation of Graphical Symbols
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO
RAIN OR MOISTURE
11 Power-Cord Protection -Power-supply cords should be
routed so that they are not likely to be walked
on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit
12 Cleaning -The unit should be cleaned only as
recommended by the manufacturer
13 Nonuse Periods -The power cord of the unit should be
unplugged from the outlet when left unused for along
period of time
14 Object and Liquid Entry -Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit
8Ventilation -The unit should be situated so that its
location or position does not interfere with its proper
ventilation For example, the unit should not be situated
on abed, sofa, rug, or similar surface, that may block the
ventilation openings, or placed
in abuilt-in installation,
such as abookcase or cabinet that may impede the flow
of air through the ventilation openings
9Heat -The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat
10 Power Sources -The unit should be connected to a
power supply only of the type described
in the operating
instructions or as marked
on the unit
The exclamation point within an equilateral
triangle is intended to alert you to the presence
01 important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance
The lightning flash with arrowhead symbol,
within an equilateral triangle,
is intended to
alert you to the presence
01 uninsulated
"dangerous voltage" within the product's
enclosure that may be
01 sullicient magnitude
to constitute arisk
01 electric shock to persons
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER-SERVICEABLE
PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
& &
L- -----'
Read Instructions -All the safety and operating
instructions should be read before the unit
is operated
2Retain Instructions -The safety and operating
instructions should be retained for future reference
3Heed Warnings -All warnings
on the unit and in the
operating instructions should
be adhered to
4Follow Instructions -All operating and other instructions
should be followed
5Water and Moisture -The unit should not be used near
water -for example, near abathtub, washbowl, kitchen
sink, laundry tub,
in awet basement, or near aswimming
pool, etc
6Carts and Stands -The unit should be used only with a
cart or stand that
is recommended by the
manufacturer
6A Aunit and cart combination should be
moved with care Quick stops, excessive
force, and uneven surfaces may cause
the unit and cart combination to overturn
15 Damage Requiring Service -The unit should be serviced
by qualified service personnel when
AThe power-supply cord or the plug has been
damaged, or
BObjects have fallen, or liquid has been spilled into the
unit, or
CThe unit has been exposed to rain, or
oThe unit does not appear to operate normally or exhibits
amarked change
in performance, or
EThe unit has been dropped, or the cabinet damaged
16 Servicing -The user should not attempt to service the
unit beyond those means described
in the operating
instructions All other servicing should be referred to
qualified service personnel
17 Power Lines -
An outdoor antenna should be located
away from power lines
18 Grounding or Polarization -Precautions should be taken
so that the grounding or polarization
is not defeated
7Wall or Ceiling Mounting -The unit should be mounted to
awall or ceiling only as recommended by the
manufacturer
CAUTION

SAFETYINSTRUCTIONS
NEG -NATIONAL ELECTRICAL CODe
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
DISCHARGE UNIT
(NEC SECTION 81G-20)
ANTENNA
LEAD IN
WIFIE
GROUNDING CONDUCTORS
INEC SECTION B'O-21j
___________ POWER SERVICE GROUNDING
'" ELECTRoDe SYSTEM
INECART250 PARTHj
ELECTRIC
SERVICE
EQUIPMENT
Note to CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and,
in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry
as practical
19 For US customers only:
OutdoorAntenna Grounding -If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode
FCC INFORMATION (for US customers only)
1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated
in the
instructions contained
in this manual, meets FCC
requirements Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product
2IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables Cable/s supplied with this
product MUST be used Follow all installation instruc-
tions Failure to follow instructions could void your FCC
authorization to use this product
in the USA
3
NOTE: This product has been tested and found to
comply with the requirements listed
in FCC Regula-
tions, Part 15 for Class "B" digital devices Compliance
with these requirements provides areasonable level of
assurance that your use of this product
in aresidential
environment will not result
in harmful interference with
other electronic devices
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found
in the users manual, may cause interference
harmful to the operation of other electronic devices
Compliance with FCC regulations does not guarantee
that interference will not occur
in all installations If
this product is found to be the source of interference,
which can be determined by turning the unit "OFF"
and "ON", please try to eliminate the problem by using
one of the following measures
Relocate either this product or the device that
is being
affected by the interference
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install
AC line filter/s
In the case of radio or TV interference, relocate/
reorient the antenna If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to coaxial type
cable
If these corrective measures do not produce satisfac-
tory results, please contact the local retailer autho-
rized to distribute this type of product If you can not
locate the appropriate retailer, please contact Yamaha
Electronics
Corp, USA 6660 Orangethorpe Ave,
Buena Park, CA 90620
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries
We Want You Listening For ALifetime
YAMAHA and the Electronic Industries Association's
Consumer Electronics Group want you to get the most out of
your equipment by playing it at asafe level One that lets the
sound come through loud and clear without annoying blaring
or distortion -and, most importantly, without affecting your
sensitive hearing
Since hearing damage from loud sounds is often gI
undetectable until it is too late, YAMAHA and the .
Electronic Industries Association's Consumer
o.
Electronics Group recommend you to avoid w.
prolonged exposure from excessive volume g¥i~~
levels
CAUTION
SAFETYINSTRUCTIONS
NEG -NATIONAL ELECTRICAL CODe
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
DISCHARGE UNIT
(NEC SECTION 81G-20)
ANTENNA
LEAD IN
WIFIE
GROUNDING CONDUCTORS
INEC SECTION B'O-21j
___________ POWER SERVICE GROUNDING
'" ELECTRoDe SYSTEM
INECART250 PARTHj
ELECTRIC
SERVICE
EQUIPMENT
Note to CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and,
in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry
as practical
19 For US customers only:
OutdoorAntenna Grounding -If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode
FCC INFORMATION (for US customers only)
1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated
in the
instructions contained
in this manual, meets FCC
requirements Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product
2IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables Cable/s supplied with this
product MUST be used Follow all installation instruc-
tions Failure to follow instructions could void your FCC
authorization to use this product
in the USA
3
NOTE: This product has been tested and found to
comply with the requirements listed
in FCC Regula-
tions, Part 15 for Class "B" digital devices Compliance
with these requirements provides areasonable level of
assurance that your use of this product
in aresidential
environment will not result
in harmful interference with
other electronic devices
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found
in the users manual, may cause interference
harmful to the operation of other electronic devices
Compliance with FCC regulations does not guarantee
that interference will not occur
in all installations If
this product is found to be the source of interference,
which can be determined by turning the unit "OFF"
and "ON", please try to eliminate the problem by using
one of the following measures
Relocate either this product or the device that
is being
affected by the interference
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install
AC line filter/s
In the case of radio or TV interference, relocate/
reorient the antenna If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to coaxial type
cable
If these corrective measures do not produce satisfac-
tory results, please contact the local retailer autho-
rized to distribute this type of product If you can not
locate the appropriate retailer, please contact Yamaha
Electronics
Corp, USA 6660 Orangethorpe Ave,
Buena Park, CA 90620
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries
We Want You Listening For ALifetime
YAMAHA and the Electronic Industries Association's
Consumer Electronics Group want you to get the most out of
your equipment by playing it at asafe level One that lets the
sound come through loud and clear without annoying blaring
or distortion -and, most importantly, without affecting your
sensitive hearing
Since hearing damage from loud sounds is often gI
undetectable until it is too late, YAMAHA and the .
Electronic Industries Association's Consumer
o.
Electronics Group recommend you to avoid w.
prolonged exposure from excessive volume g¥i~~
levels
CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
To assure the finest performance, please read this
manual carefully Keep it in asafe place for future
reference
2Install this
unit in acool, dry, clean place -away
from windows, heat sources, sources
of excessive
vibration, dust, moisture and cold Avoid sources
of
humming (transformers, motors) To preventfire or
electrical shock, do not expose the unit to rain or
water
3Never open the cabinet
If something drops into the
unit, contact your dealer
4Do
not use force on switches, controls or connection
cables When moving the unit,
first disconnect the
power cord and then the cables connected
to other
component Never pull the cables themselves
5The openings
on the cover assure proper ventilation
of the unit If these openings are obstructed, the
temperature inside the
unit will rise rapidly
Therefore, avoid placing objects against these
openings, and install the
unit in awell-ventilated area
to prevent fire and damage
6The voltage used
must be the same as that specified
on
this unit Using this unit with ahigher voltage than
specified is dangerous and may result in fire
or other
accidents YAMAHA will
not be held responsible for
any damage resulting from the use of this unit with a
voltage
other than that specified
7Digital signals generated by
this unit may interfere
with other component such as tuners, receivers and
TVs Move
this unit farther away from such
component
if interference is observed
8Always setVOLUME
to the "00" position before
starting the audio source play Increase the volume
gradually
to an appropriate level after playback has
been started
9Do
not attempt to clean the unit with chemical
solvents; this
might damage the finish Use aclean,
dry cloth
10 Be sure to read the"TROUBLESHOOTING" section
regarding common operating errors before
concluding that the unit
is faulty
11 When not planning to use this unit for along period
of time (e g ,a vacation), disconnect the
AC power
cord from the wall outlet
CAUTION
12 To prevent lightning damage, disconnectthe AC
power cord and disconnectthe antenna cable when
there
is an electrical storm
13 Grounding or polarization -Precautions should be
taken
so thatthe grounding or polarization of the unit
is not defeated
14
AC outlet -Do not connect audio component to the
AC outlet on the rear panel if that component
requires more power than the outlet
is rated to
provide
This unit is not disconnected from the AC power source
as long
as it is connected to the wall outlet, even if this
unit itself
is turned off This state is called the standby
mode In this state, this unit is designed to consume a
very small quantity
of power
IMPORTANT
Please record the serial number of this unit in the space
below
MODEL:
Serial No :
The serial number
is located on the rear of the unit
Retain this Owner's Manual in asafe place for future
reference
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert
This Class Bdigital apparatus complies with Canadian
ICES-003
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
To assure the finest performance, please read this
manual carefully Keep it in asafe place for future
reference
2Install this
unit in acool, dry, clean place -away
from windows, heat sources, sources
of excessive
vibration, dust, moisture and cold Avoid sources
of
humming (transformers, motors) To preventfire or
electrical shock, do not expose the unit to rain or
water
3Never open the cabinet
If something drops into the
unit, contact your dealer
4Do
not use force on switches, controls or connection
cables When moving the unit,
first disconnect the
power cord and then the cables connected
to other
component Never pull the cables themselves
5The openings
on the cover assure proper ventilation
of the unit If these openings are obstructed, the
temperature inside the
unit will rise rapidly
Therefore, avoid placing objects against these
openings, and install the
unit in awell-ventilated area
to prevent fire and damage
6The voltage used
must be the same as that specified
on
this unit Using this unit with ahigher voltage than
specified is dangerous and may result in fire
or other
accidents YAMAHA will
not be held responsible for
any damage resulting from the use of this unit with a
voltage
other than that specified
7Digital signals generated by
this unit may interfere
with other component such as tuners, receivers and
TVs Move
this unit farther away from such
component
if interference is observed
8Always setVOLUME
to the "00" position before
starting the audio source play Increase the volume
gradually
to an appropriate level after playback has
been started
9Do
not attempt to clean the unit with chemical
solvents; this
might damage the finish Use aclean,
dry cloth
10 Be sure to read the"TROUBLESHOOTING" section
regarding common operating errors before
concluding that the unit
is faulty
11 When not planning to use this unit for along period
of time (e g ,a vacation), disconnect the
AC power
cord from the wall outlet
CAUTION
12 To prevent lightning damage, disconnectthe AC
power cord and disconnectthe antenna cable when
there
is an electrical storm
13 Grounding or polarization -Precautions should be
taken
so thatthe grounding or polarization of the unit
is not defeated
14
AC outlet -Do not connect audio component to the
AC outlet on the rear panel if that component
requires more power than the outlet
is rated to
provide
This unit is not disconnected from the AC power source
as long
as it is connected to the wall outlet, even if this
unit itself
is turned off This state is called the standby
mode In this state, this unit is designed to consume a
very small quantity
of power
IMPORTANT
Please record the serial number of this unit in the space
below
MODEL:
Serial No :
The serial number
is located on the rear of the unit
Retain this Owner's Manual in asafe place for future
reference
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert
This Class Bdigital apparatus complies with Canadian
ICES-003

5-Channel Power Amplification
+ Minimum RMS Output
(0 06% THD, 20 Hz - 20 kHz)
[U SA and Canada models]
Main 1oow+1oow(8Q)
Center 100 W (8 Q)
Rear lOOW+lOOW(8Q)
[Australia model]
Main 7OW+7OW(8Q)
Center 70 W (8 a)
Rear 7OW+7OW(852)
Multi-Mode Digital Sound Field
Processing
+ Digital Sound Field Processor (DSP)
+ Dolby Pro Logic Decoder
+ Dolby Digital Decoder
+ DTS Decoder
+ CINEMA DSP Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital or
DTS
Sophisticated FM/AM Tuner
+ 40-Station Random AccessPreset Tuning
+ Automatic PresetTuning
+ Preset Station Shifting Capability (Preset Editing)
Other Features
+ 96-kHz/24-bit D/A Converter
+ “SET MENU” which Provides You with 12 Items
for Optimizing This Unit for Your AudioiVideo
System
+ TestTone Generator for Easier Speaker Balance
Adjustment
+ 6-Channel External Decoder Input for Other Future
Formats
+ SVideo Signal Input/Output Capability
+ 3 Optical/2 Coaxial Digital Signal Input Terminals
+ SLEEPTimer
+ Remote Control with Preset Manufacturer Codes
a[1 m Manufactured under license from Dolby Laboratories “Dolby”, “Plo Logic” and the
DIGITAL
double-l) symbol are trademarks of Dolby
Labotatortes Confidential Unpublished Works
01992 - 1997 Dolby Laboratories, lnc All
rights reserved
DIGITAL
m
SURROUND
Manufactured under license from D&al Theatet Systems, Inc
US Pat No 5.45 I 942 and other world-wide patents issued and
pending ‘DTS”, ‘ DTS Digital Suttound”, ale tladematks 01
Digital Theate! Systems, Inc Copylight 1996 Digital Theater
Systems. Inc All Rights Recaved
s& indicates a tip for your operation
.
When buttons on this unit and the remote control are
noted togethel in this Owner’s Manual, these button
names are in principle noted in the order of “button name
(lemote control button name)”
FEATURES CONTENTS
D[] IDOLBY I
DIGITAL
I
::'<il~ indicates atip for your operation
•When buttons on this unit and the remote control are
noted togethel in this Owner's Manual, these button
names are in principle noted in the order
of "button name
(lemote control button name)"
5-Channel Power Amplification
•Minimum RMS Output
(0 06% THD, 20 Hz -20 kHz)
[U S A and Canada models]
Main 100 W+100 W (8 Q)
Center 100 W(8 Q)
Rear 100 W+100 W (8 Q)
[Australia model]
Main 70 W+70 W (8 Q)
Center 70 W (8 Q)
Rear 70 W+70 W (8 Q)
Multi-Mode Digital Sound Field
Processing
•Digital Sound Field Processor (DSP)
•Dolby Pro Logic Decoder
•Dolby Digital Decoder
•DTS Decoder
•CINEMA DSP Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital or
DTS
Sophisticated FM/AM Tuner
•40-Station Random Access Preset Tuning
•Automatic Preset Tuning
•Preset Station Shifting Capability (Preset Editing)
Other Features
•96-kHzI24-bit D/A Converter
•"SET MENU" which Provides You with 12 Items
for Optimizing This Unit for Your AudioNideo
System
•Test Tone Generator for Easier Speaker Balance
Adjustment
•6-Channel External Decoder Input for Other Future
Formats
• S Video Signal Input/Output Capability
• 3 Opticall2 Coaxial Digital Signal Input Terminals
•SLEEPTimer
•Remote Control with Preset Manufacturer Codes
Manufactuted under license hom Dolby
LabOlatories "Dolby", "PIO Logic" and the
double-D symbol are trademarks
of Dolby
LabOlatories Confidential Unpublished Works
©1992 -1997 Dolby Laboratories, Inc All
rights reselved
DIG I TAL Manufactured under license from Digital Theatel Systems, Inc
~ US Pat No 5,451 942 and othel world-wide patents issued and
SU~ROUND pending 'DTS",' DTS Digital SUllound", ate ttademalks of
Digital Thcatel Systems, Inc Copy! ight 1996 Digital Theme!
Systems, Inc All Rights Reselved
1
FEATURES CONTENTS
D[] IDOLBY I
DIGITAL
I
::'<il~ indicates atip for your operation
•When buttons on this unit and the remote control are
noted togethel in this Owner's Manual, these button
names are in principle noted in the order
of "button name
(lemote control button name)"
5-Channel Power Amplification
•Minimum RMS Output
(0 06% THD, 20 Hz -20 kHz)
[U S A and Canada models]
Main 100 W+100 W (8 Q)
Center 100 W(8 Q)
Rear 100 W+100 W (8 Q)
[Australia model]
Main 70 W+70 W (8 Q)
Center 70 W (8 Q)
Rear 70 W+70 W (8 Q)
Multi-Mode Digital Sound Field
Processing
•Digital Sound Field Processor (DSP)
•Dolby Pro Logic Decoder
•Dolby Digital Decoder
•DTS Decoder
•CINEMA DSP Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital or
DTS
Sophisticated FM/AM Tuner
•40-Station Random Access Preset Tuning
•Automatic Preset Tuning
•Preset Station Shifting Capability (Preset Editing)
Other Features
•96-kHzI24-bit D/A Converter
•"SET MENU" which Provides You with 12 Items
for Optimizing This Unit for Your AudioNideo
System
•Test Tone Generator for Easier Speaker Balance
Adjustment
•6-Channel External Decoder Input for Other Future
Formats
• S Video Signal Input/Output Capability
• 3 Opticall2 Coaxial Digital Signal Input Terminals
•SLEEPTimer
•Remote Control with Preset Manufacturer Codes
Manufactuted under license hom Dolby
LabOlatories "Dolby", "PIO Logic" and the
double-D symbol are trademarks
of Dolby
LabOlatories Confidential Unpublished Works
©1992 -1997 Dolby Laboratories, Inc All
rights reselved
DIG I TAL Manufactured under license from Digital Theatel Systems, Inc
~ US Pat No 5,451 942 and othel world-wide patents issued and
SU~ROUND pending 'DTS",' DTS Digital SUllound", ate ttademalks of
Digital Thcatel Systems, Inc Copy! ight 1996 Digital Theme!
Systems, Inc All Rights Reselved
1

GETTING STARTED
Check that the following items are included in your package
Remote control
@YAMAIIA
Batteries (AAA, ROa, UM-4 type)
Indoor FM antenna
AM loop antenna
Antenna adapter
(U 5 A and Canada models only)
Quick reference card
Connection guide
If the remote control operates only when it is close to the
unit, the batteries are weak Replace all the batteries with
new ones
Be sure to replace the battelies within about two minutes
If it takes longer than two minutes, the codes set for the
lemote control will return to the factory settings (Refer
to pages 42 to 49 about the remote control)
oTurn the remote control over and slide the
battery compartment cover in the direction of
the arrow.
fa Insert the batteries (AAA, R03 or UM-4 type)
according the polarity markings on the inside
of the battery compartment.
6Close the battery compartment cover.
2
•Use only AAA, R03 01 UM-4 batteIies fOt leplacement
•Be SUle the battery polatity is conect (See the illustration inside
the battely compattment)
•Remove the batteries if the remote conllo! will not be used fOt an
extended period of time
• If the battelies have leaked, dispose of them immediately Avoid
touching the leaked matetial Ot letting it come into contact with
clothing, etc Clean the battety compartment tholOughly befOte
installing new batteries
GETTING STARTED
Check that the following items are included in your package
Remote control
@YAMAIIA
Batteries (AAA, ROa, UM-4 type)
Indoor FM antenna
AM loop antenna
Antenna adapter
(U 5 A and Canada models only)
Quick reference card
Connection guide
If the remote control operates only when it is close to the
unit, the batteries are weak Replace all the batteries with
new ones
Be sure to replace the battelies within about two minutes
If it takes longer than two minutes, the codes set for the
lemote control will return to the factory settings (Refer
to pages 42 to 49 about the remote control)
oTurn the remote control over and slide the
battery compartment cover in the direction of
the arrow.
fa Insert the batteries (AAA, R03 or UM-4 type)
according the polarity markings on the inside
of the battery compartment.
6Close the battery compartment cover.
2
•Use only AAA, R03 01 UM-4 batteIies fOt leplacement
•Be SUle the battery polatity is conect (See the illustration inside
the battely compattment)
•Remove the batteries if the remote conllo! will not be used fOt an
extended period of time
• If the battelies have leaked, dispose of them immediately Avoid
touching the leaked matetial Ot letting it come into contact with
clothing, etc Clean the battety compartment tholOughly befOte
installing new batteries

GETTING STARTED
The remote control transmits adirectional infrared beam Be
sure to aim the remote control directly at the infrared sensor
during operation When the sensor
is covered or there is a
large object between the remote control and the sensor, the
sensOl cannot receive signals The sensor may not be able to
receive signals properly when it is exposed to direct sunlight
01 astrong artificial light (such as af]uOlescent or strobe
light)
In this case, change the direction of the light or
reposition the unit to avoid direct lighting
•Handle Ihe temote contlOl with Cale
•
Do not spill watel, tea 01 othet liquids on the lemote control
•Do not dlOP the [emote control
•Do not leave
01 stOle the remote contlO! in the following
conditions:
-high humidity
Ot tempetatute such as near aheatel, stove 01
bath;
-dusty places;
01
-exttemely low tempetatute
I
3
GETTING STARTED
The remote control transmits adirectional infrared beam Be
sure to aim the remote control directly at the infrared sensor
during operation When the sensor
is covered or there is a
large object between the remote control and the sensor, the
sensOl cannot receive signals The sensor may not be able to
receive signals properly when it is exposed to direct sunlight
01 astrong artificial light (such as af]uOlescent or strobe
light)
In this case, change the direction of the light or
reposition the unit to avoid direct lighting
•Handle Ihe temote contlOl with Cale
•
Do not spill watel, tea 01 othet liquids on the lemote control
•Do not dlOP the [emote control
•Do not leave
01 stOle the remote contlO! in the following
conditions:
-high humidity
Ot tempetatute such as near aheatel, stove 01
bath;
-dusty places;
01
-exttemely low tempetatute
I
3

CONTROLS AND FUNCTIONS
4»
4t
4:'
4,t
4~
4~
@YA
~AHA
~
ffi~
tra:l
INPUT S~LECTDR
IT
[----- - -
--
------- ------- -
--
- - - - - -- - - --
~
0-
~
~
--------------------- ------------- - --
-'
NPcJTwOOe
1/
iii
; m""1
C::,:.:~
I~
11
-"'
j!
II "i-
ii it
~~~~
BASS
Q
BALANGE
PHONES
I ~OA",R~ II
QQ
VIDEO AUX-
@)
I§ I§
0
~~~
s"''"'o
"'"''''
'''''''-0 P
-
--
[I-I=
1""'-""
4~
41)
4!) 4~
4~ 4~ 49 4D
l~ l~ 4
D4i)
4~
EID
oSTANDBY/ON
Ptess this switch
to tum on the powet of this unit Ot to set
this unit in the standby mode Before tUlning the powet on,
set VOLUME to the
"00" position
Standby mode
In this mode, this unit consumes avety small quantity
of
power to teceive infrated-signals from the temote
conttol
8Remote control sensor
This teceives signals from the remote conttol
eDisplay
This shows vatious infotmation (Refer to page 6fot
details)
oINPUT MODE
Press this button to select the input mode among AUTO,
DTS and ANALOG for the DVDILD, TV/digital TV and
cable TV/satellite tuner sources
oINPUT SELECTOR
Turn this selector
to select the input sOUlce (TUNER, CD,
PHONO, CBL/SAT, V-AUX, VCR, D-
TV, DVDILD) that
you want to listen to or watch The arrow
f01 the selected
input source indicator lights up on the display
4
•VOLUME
Turn this control to turn up or down the volume
•PHONES jack
Connect the headphones to the PHONES
jack You can
listen to the sound to be output from the main speakers
thtough the headphones
When listening with headphones privately, set both
SPEAKERS Aand B
to the OFF position, press EFFECT to
tUln offthe effect speakers (centet and rear) and set "BASS
OUT" on the SET MENU to the MAIN position (so that no
DSP program name appears on the display)
oSPEAKERS
Set A
or B(or both Aand B) to the ON position for the main
speaker system (connected to this unit) that you want to use
Set the button(s) to the OFF position for the main speaker
system that you don't want to use
oPROGRAM selector
Press
-<J or C> to select aDSP program when the effect
speakets (center and rear) are turned on The name
of the
selected program appears on the display
~ EFFECT
Press this button
to tum on or off the effect speakets (center
and tear) If you turn them off, the signals
of the center and
tear channels are directed to the right and left main speakers
when playing a
sOUlce encoded with Dolby Digital and
DTS In this case, the output levels
of the right and left
speakers may not match
CONTROLS AND FUNCTIONS
4»
4t
4:'
4,t
4~
4~
@YA
~AHA
~
ffi~
tra:l
INPUT S~LECTDR
IT
[----- - -
--
------- ------- -
--
- - - - - -- - - --
~
0-
~
~
--------------------- ------------- - --
-'
NPcJTwOOe
1/
iii
; m""1
C::,:.:~
I~
11
-"'
j!
II "i-
ii it
~~~~
BASS
Q
BALANGE
PHONES
I ~OA",R~ II
QQ
VIDEO AUX-
@)
I§ I§
0
~~~
s"''"'o
"'"''''
'''''''-0 P
-
--
[I-I=
1""'-""
4~
41)
4!) 4~
4~ 4~ 49 4D
l~ l~ 4
D4i)
4~
EID
oSTANDBY/ON
Ptess this switch
to tum on the powet of this unit Ot to set
this unit in the standby mode Before tUlning the powet on,
set VOLUME to the
"00" position
Standby mode
In this mode, this unit consumes avety small quantity
of
power to teceive infrated-signals from the temote
conttol
8Remote control sensor
This teceives signals from the remote conttol
eDisplay
This shows vatious infotmation (Refer to page 6fot
details)
oINPUT MODE
Press this button to select the input mode among AUTO,
DTS and ANALOG for the DVDILD, TV/digital TV and
cable TV/satellite tuner sources
oINPUT SELECTOR
Turn this selector
to select the input sOUlce (TUNER, CD,
PHONO, CBL/SAT, V-AUX, VCR, D-
TV, DVDILD) that
you want to listen to or watch The arrow
f01 the selected
input source indicator lights up on the display
4
•VOLUME
Turn this control to turn up or down the volume
•PHONES jack
Connect the headphones to the PHONES
jack You can
listen to the sound to be output from the main speakers
thtough the headphones
When listening with headphones privately, set both
SPEAKERS Aand B
to the OFF position, press EFFECT to
tUln offthe effect speakers (centet and rear) and set "BASS
OUT" on the SET MENU to the MAIN position (so that no
DSP program name appears on the display)
oSPEAKERS
Set A
or B(or both Aand B) to the ON position for the main
speaker system (connected to this unit) that you want to use
Set the button(s) to the OFF position for the main speaker
system that you don't want to use
oPROGRAM selector
Press
-<J or C> to select aDSP program when the effect
speakets (center and rear) are turned on The name
of the
selected program appears on the display
~ EFFECT
Press this button
to tum on or off the effect speakets (center
and tear) If you turn them off, the signals
of the center and
tear channels are directed to the right and left main speakers
when playing a
sOUlce encoded with Dolby Digital and
DTS In this case, the output levels
of the right and left
speakers may not match

4D Tone controls
These controls are only effective for the sound from the
main speakels
a) BASS
Tum this control clockwise to increase or counterclockwise
to decrease the low-frequency response The "0" position
ploduces aflat response
b) TREBLE
Tum this control clockwise
to increase or counterclockwise
to decrease the high-frequency response The "0" position
produces aflat lesponse <
~ TAPElMD MON I EXT. DECODER
Press this button to select atape or an MD source The
"TAPE/MD MONITOR" indicator lights up on the display
When you press the button again, the "TAPEIMD
MONITOR" indicator goes off, "EXT DECODER" appears
on the display and you can listen to asource connected to
the EXTERNAL DECODER INPUT terminals
4i) BALANCE
This control
is only effective for the sound from the main
speakels
Tum the control
to adjust the balance of the output volume
from the light and left main speakers to compensate for
sound imbalance caused by the speakel location or listening
room conditions
4D AlB/C/D/E
Press this button to select one of agroup (A to E) of preset
stations
CONTROLS AND FUNCTIONS
~ PRESETITUNING
When" : " appears on the display
This button is used to select apreset station number
(1 to 8)
Press
l> to select ahigher and <J to select alower preset
station number
When" : " goes off from the display
This button
is used for tuning Press l> to tune in to higher
frequencies, and <J to tune
in to lower frequencies
~ PRESETITUNING, EDIT
Pless this button
to turn on or off" : " on the display, and
switch the function between storing abroadcasting station
(preset tuning) and tuning This button
is also used to
exchange the assignment of two preset stations with each
other
4D FM/AM
Pless this button to switch the reception band between FM
and AM
4ID MEMORY (MAN'UAUTO FM)
Press this button to store broadcasting stations Hold down
this button for
mOle than three seconds to begin automatic
preset tuning
4i> TUNING MODE (AUTO/MAN'L MONO)
Pless this button
to switch the tuning mode between
automatic and manual
To use the automatic tuning method,
press this button so that the "AUTO" indicator lights up on
the display
To use the manual tuning method, press this
button
so that the "AUTO" indicator goes off
~ VIDEO AUX terminals
Connect an auxiliary audio or video input source such
as a
camcorder to these terminals
If the connected video unit
has an Svideo output terminal, connect it to the SVIDEO
terminal to obtain ahigh-resolution picture Use INPUT
SELECTOR to select the source connected to these
terminals
I
5
4D Tone controls
These controls are only effective for the sound from the
main speakels
a) BASS
Tum this control clockwise to increase or counterclockwise
to decrease the low-frequency response The "0" position
ploduces aflat response
b) TREBLE
Tum this control clockwise
to increase or counterclockwise
to decrease the high-frequency response The "0" position
produces aflat lesponse <
~ TAPElMD MON I EXT. DECODER
Press this button to select atape or an MD source The
"TAPE/MD MONITOR" indicator lights up on the display
When you press the button again, the "TAPEIMD
MONITOR" indicator goes off, "EXT DECODER" appears
on the display and you can listen to asource connected to
the EXTERNAL DECODER INPUT terminals
4i) BALANCE
This control
is only effective for the sound from the main
speakels
Tum the control
to adjust the balance of the output volume
from the light and left main speakers to compensate for
sound imbalance caused by the speakel location or listening
room conditions
4D AlB/C/D/E
Press this button to select one of agroup (A to E) of preset
stations
CONTROLS AND FUNCTIONS
~ PRESETITUNING
When" : " appears on the display
This button is used to select apreset station number
(1 to 8)
Press
l> to select ahigher and <J to select alower preset
station number
When" : " goes off from the display
This button
is used for tuning Press l> to tune in to higher
frequencies, and <J to tune
in to lower frequencies
~ PRESETITUNING, EDIT
Pless this button
to turn on or off" : " on the display, and
switch the function between storing abroadcasting station
(preset tuning) and tuning This button
is also used to
exchange the assignment of two preset stations with each
other
4D FM/AM
Pless this button to switch the reception band between FM
and AM
4ID MEMORY (MAN'UAUTO FM)
Press this button to store broadcasting stations Hold down
this button for
mOle than three seconds to begin automatic
preset tuning
4i> TUNING MODE (AUTO/MAN'L MONO)
Pless this button
to switch the tuning mode between
automatic and manual
To use the automatic tuning method,
press this button so that the "AUTO" indicator lights up on
the display
To use the manual tuning method, press this
button
so that the "AUTO" indicator goes off
~ VIDEO AUX terminals
Connect an auxiliary audio or video input source such
as a
camcorder to these terminals
If the connected video unit
has an Svideo output terminal, connect it to the SVIDEO
terminal to obtain ahigh-resolution picture Use INPUT
SELECTOR to select the source connected to these
terminals
I
5

CONTROLS AND FUNCTIONS
1'tI Iftl 1'tI 1'tI liJil 1'tI 1'tI 1'tI 1'tI 1'tI IW IW IW Iftl DVO /CO <l' I> nX<,c ]
I III DIGITAL I IZ!SI JZ!SI JZ!SI JZ!SI IZ!SI IZ!SI IZ!SI JZ!SI IZ!SI IZ!SI IZ!SI IZ!SI IZ!SI IZ!SI g,~ 0- TV <J [> CD
1 III PRO LOGIC) VCR <J [> PHONO
II I ~r'~~ ~"~O -~-" ~M~' ~['_O ... <om V-AUX<l .. C</MO
__ ~A==r_S_p_OR_T_S OI_SC_O __ §_g_8K_CE_~O_TN_~_~E_1~O';;";~fii~'L~C:B:L:/:SA:T:<J= __ M_O_N~~i::J
• dts indicator
The "dts" indicatOl lights up when the built-in DTS
decoder
is on
•DSP program indicators
The name of the selected DSP progtam lights up in the
following cases:
•When the tuner
is selected as the input source
•When DSP program No
2, 3or the subprogram
"ENHANCED"
of No I is selected
eMulti-information display
This display shows various information: for example the
name
of the selected DSP program and the various settings
during adjustment with the SET MENU The current station
frequency and band (FM or AM) also appear when the tuner
is selected as the input source
eInput source indicators
One of the arrows for these indicatorslights up depending
on which source is selected
oTAPElMD MONITOR indicator
This lights up when the tape deck or MD recorder, etc is
selected
as the input source by pressing TAPEIMD MON /
EXT DECODER
(Ot TAPEIMD)
6
o ( III DIGITAL Iand (III PRO LOGIC) indicators
" I III DIGITAL I" lights up when the built-in Dolby Digital
decoder
is on "I III PRO LOGIC I" lights up when the built-in
Dolby Pro Logic decoder is
on
• 1 DSP )indicator
" I DSP I" lights up when the built-in digital sound
field processor is on
eMEMORY indicator
This flashes for about five seconds after pressing
MEMORY During this period, the displayed station can be
stored in the memory
oAUTO indicator
This lights up when the unit is in the automatic tuning
mode
4@ STEREO indicator
This lights up when an FM stereo blOadcast with sufficient
signal strength is being received
mSignal-level indicator
This indicates the signal level of the station being received
If multipath interference is detected, the indication
decreases
48 SLEEP indicator
This lights up while the built-in SLEEP timer is on
CONTROLS AND FUNCTIONS
1'tI Iftl 1'tI 1'tI liJil 1'tI 1'tI 1'tI 1'tI 1'tI IW IW IW Iftl DVO /CO <l' I> nX<,c ]
I III DIGITAL I IZ!SI JZ!SI JZ!SI JZ!SI IZ!SI IZ!SI IZ!SI JZ!SI IZ!SI IZ!SI IZ!SI IZ!SI IZ!SI IZ!SI g,~ 0- TV <J [> CD
1 III PRO LOGIC) VCR <J [> PHONO
II I ~r'~~ ~"~O -~-" ~M~' ~['_O ... <om V-AUX<l .. C</MO
__ ~A==r_S_p_OR_T_S OI_SC_O __ §_g_8K_CE_~O_TN_~_~E_1~O';;";~fii~'L~C:B:L:/:SA:T:<J= __ M_O_N~~i::J
• dts indicator
The "dts" indicatOl lights up when the built-in DTS
decoder
is on
•DSP program indicators
The name of the selected DSP progtam lights up in the
following cases:
•When the tuner
is selected as the input source
•When DSP program No
2, 3or the subprogram
"ENHANCED"
of No I is selected
eMulti-information display
This display shows various information: for example the
name
of the selected DSP program and the various settings
during adjustment with the SET MENU The current station
frequency and band (FM or AM) also appear when the tuner
is selected as the input source
eInput source indicators
One of the arrows for these indicatorslights up depending
on which source is selected
oTAPElMD MONITOR indicator
This lights up when the tape deck or MD recorder, etc is
selected
as the input source by pressing TAPEIMD MON /
EXT DECODER
(Ot TAPEIMD)
6
o ( III DIGITAL Iand (III PRO LOGIC) indicators
" I III DIGITAL I" lights up when the built-in Dolby Digital
decoder
is on "I III PRO LOGIC I" lights up when the built-in
Dolby Pro Logic decoder is
on
• 1 DSP )indicator
" I DSP I" lights up when the built-in digital sound
field processor is on
eMEMORY indicator
This flashes for about five seconds after pressing
MEMORY During this period, the displayed station can be
stored in the memory
oAUTO indicator
This lights up when the unit is in the automatic tuning
mode
4@ STEREO indicator
This lights up when an FM stereo blOadcast with sufficient
signal strength is being received
mSignal-level indicator
This indicates the signal level of the station being received
If multipath interference is detected, the indication
decreases
48 SLEEP indicator
This lights up while the built-in SLEEP timer is on

CONTROLS AND FUNCTIONS
This section describes the basic operation of this unit with
the remote control First, set the selector dial
to the AMP/
TUN position Refer to "PRESET REMOTE CONTROL"
on page 42 for full details
Select the
AMP/TUN
position
EFFECT
Refer to
pageS
TV POWER
TV VOLUME
oDSP
Pless this button to switch the function of the numeric
buttons
to the DSP plOgram selector (Refer to page 8 )
8Indicator window
This displays the name of components which can be
controlled
eNumeric buttons (Input selector buttons)
These buttons select the input source
CD:
To playa CD
TUNER
To listen to an FM OJ AM blOadcast
TAPE/MD:
To playa tape OJ MD
DVD/LD:
To playa DVD 01 LD
0- TV: To watch aTV
VCR:
To playa video cassette
PHONO:
To play an analog record
CBL/SAT:
To watch cable TV OJ satellite blOadcast
V-AUX:
To use acamcordel
EXT
DEC: To play anothel multi-channel source
Refel
to page 8 fOJ details
GTEST
Press this button to output the test tone for each speaker
o<(left), >(right)
These buttons adjust the settings of the SET MENU and
TIMEILEVEL mode
eTIME/LEVEL
Press this button to select the items in the TIMEILEVEL
mode
f) SLEEP
Pless this button to set the SLEEP timer
Ci) INPUT
Press this button to switch the function of the numeric
buttons to the input selector (Refer to page 8 )
oIndicator
This flashes in led when pressing abutton on the remote
contlol
G> Selector dial
Turn this dial to select the position for the component to be
contlOlled (The plOper code must be set for
yoU!
component Refel to "Setup codes" on page 48 )When the
position
is selected, the lemote contlOl is set to that
component operation mode I
7
CONTROLS AND FUNCTIONS
This section describes the basic operation of this unit with
the remote control First, set the selector dial
to the AMP/
TUN position Refer to "PRESET REMOTE CONTROL"
on page 42 for full details
Select the
AMP/TUN
position
EFFECT
Refer to
pageS
TV POWER
TV VOLUME
oDSP
Pless this button to switch the function of the numeric
buttons
to the DSP plOgram selector (Refer to page 8 )
8Indicator window
This displays the name of components which can be
controlled
eNumeric buttons (Input selector buttons)
These buttons select the input source
CD:
To playa CD
TUNER
To listen to an FM OJ AM blOadcast
TAPE/MD:
To playa tape OJ MD
DVD/LD:
To playa DVD 01 LD
0- TV: To watch aTV
VCR:
To playa video cassette
PHONO:
To play an analog record
CBL/SAT:
To watch cable TV OJ satellite blOadcast
V-AUX:
To use acamcordel
EXT
DEC: To play anothel multi-channel source
Refel
to page 8 fOJ details
GTEST
Press this button to output the test tone for each speaker
o<(left), >(right)
These buttons adjust the settings of the SET MENU and
TIMEILEVEL mode
eTIME/LEVEL
Press this button to select the items in the TIMEILEVEL
mode
f) SLEEP
Pless this button to set the SLEEP timer
Ci) INPUT
Press this button to switch the function of the numeric
buttons to the input selector (Refer to page 8 )
oIndicator
This flashes in led when pressing abutton on the remote
contlol
G> Selector dial
Turn this dial to select the position for the component to be
contlOlled (The plOper code must be set for
yoU!
component Refel to "Setup codes" on page 48 )When the
position
is selected, the lemote contlOl is set to that
component operation mode I
7

CONTROLS AND FUNCTIONS
4D AlB/C/D/E, PRESET +/-
These buttons are used to select apreset station
AlB/C/DIE: To select one of agroup (A to E) of preset
stations
PRESET +/-:
To select apreset station number (I to 8)
48 v(next), A(back)
These buttons are used to advance or go back one selection
on the SET MENU and TIMEILEVEL mode
~ SET MENU
Press this button to select the items on the SET MENU
4D POWER
Press this button to turn this unit on
4I; STANDBY
Press this button to set this unit in the standby mode
~ VOLUME (+/-)
These buttons are used to adjust the volume level
4fI MUTE
Press this button to mute the sound To cancel mute, press
this button again
EFFECT
Press this button to turn on or offthe effect speakers (center
and teat) in the following cases:
•When the selector dial
is set to the DSP/TUN position
•While the indicator is lit
fOl about three seconds after
ptessing DSP
The Numeric buttons function in various ways depending
on the position
of the selector dial or the combination of
other instructions
•When selecting an input source
DPress INPUT regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6 You can select an input source with the
numeric buttons while the indicator is lit.
8
•When selecting aDSP program
and turning on or off the effect
speakers (center and rear)
A B
A
oPress DSP regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6 You can select aDSP program with the
numeric buttons
(1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT while the indicator is lit.
B
DSet the selector dial to the DSPITUN position.
6 You can select aDSP program directly with the
numeric buttons
(1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT.
•When selecting apreset station
number
DSet code number "0023" in the AMPITUN (or
DSPITUN) position.
Refet to page 48 for setting the code
6Set the selector dial to the AMPITUN (or DSP/
TUN) position.
!J You can select apreset station number directly
with the numeric buttons
(1 to 8).
Refer to page 29
CONTROLS AND FUNCTIONS
4D AlB/C/D/E, PRESET +/-
These buttons are used to select apreset station
AlB/C/DIE: To select one of agroup (A to E) of preset
stations
PRESET +/-:
To select apreset station number (I to 8)
48 v(next), A(back)
These buttons are used to advance or go back one selection
on the SET MENU and TIMEILEVEL mode
~ SET MENU
Press this button to select the items on the SET MENU
4D POWER
Press this button to turn this unit on
4I; STANDBY
Press this button to set this unit in the standby mode
~ VOLUME (+/-)
These buttons are used to adjust the volume level
4fI MUTE
Press this button to mute the sound To cancel mute, press
this button again
EFFECT
Press this button to turn on or offthe effect speakers (center
and teat) in the following cases:
•When the selector dial
is set to the DSP/TUN position
•While the indicator is lit
fOl about three seconds after
ptessing DSP
The Numeric buttons function in various ways depending
on the position
of the selector dial or the combination of
other instructions
•When selecting an input source
DPress INPUT regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6 You can select an input source with the
numeric buttons while the indicator is lit.
8
•When selecting aDSP program
and turning on or off the effect
speakers (center and rear)
A B
A
oPress DSP regardless of the position of the
selector dial.
The indicator lights up for about three seconds
6 You can select aDSP program with the
numeric buttons
(1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT while the indicator is lit.
B
DSet the selector dial to the DSPITUN position.
6 You can select aDSP program directly with the
numeric buttons
(1 to 8) and turn on or off the
effect speakers (center and rear) by pressing
EFFECT.
•When selecting apreset station
number
DSet code number "0023" in the AMPITUN (or
DSPITUN) position.
Refet to page 48 for setting the code
6Set the selector dial to the AMPITUN (or DSP/
TUN) position.
!J You can select apreset station number directly
with the numeric buttons
(1 to 8).
Refer to page 29

SPEAKER SETUP
Rear speaker (L)
Main speaker (R)
~,:
Refer to the following diagram when you place the
speakels
Main
speaker (L)
Center speaker
•Main speakers
Place the light and left main speakers an equal distance
from the ideal listening position The distance
of each
speaker from each side
of the TV monitor should be the
same
•Rear speakers
Place these speakels behind your listening position, facing
slightly inwards, neaI1y
18m (approx 6feet) above the
floO!
•If the cenler speakeI is not used, the centel channel sound will be
heatd flom the tight and left main speakels In that case,
"CENTER SP" on the SET MENU
is set to the NONE position
(Refet to page 36
fOJ details)
•Center speaker
Align the flOnt face of the center speaker with the flOnt face
of yoU! TV monitor Place the speaker as close to the
monitor
as possible, such as directly over or under the
monitol and centrally between the main speakers
The main speakels are used for the main soU!ce sound plus
the effect sounds They will probably be the speakels from
yoU! present stereo system The rear speakers are used for
the effect and surround sounds, and the center speaker
is for
the center sounds (dialog, vocals,
etc) If fO! some leason it
is not practical to use acenter speakel, you can do without
it Best results, however, are obtained with the full system
This unit is designed to provide the best sound-field quality
with a5-speaker system, using main speakers, rear speakels
and acenter speaker
If you use different brands of speakers
(with different tonal qualities) in your system, the tone
of a
moving human voice and other types
of sound may not shift
smoothly
We recommend that you use speakels from the
same manufacture
or speakers with the same tonal quality
The main speakers should be high-pelfO!mance models and
have enough power-handling capacity
to accept the
maximum output
of your audio system The other speakels
do not have to be equal to the main speakers For precise
sound localization, however, it is ideal
to use high-
performance models that can reproduce sounds ovel the full
range for the center speaker and the leal speakers
•Use of asubwoofer expands your
sound field
It is also possible to fU!ther expand yoU! system with the
addition
of asubwoofer The use of asubwoofer is effective
not only for reinforcing bass frequencies from any or all
channels, but also for replOducing the LFE (low frequency
effect) channel with high fidelity when playing back a
source encoded with Dolby Digital or DTS The YAMAHA
Active Servo Processing Subwoofer System
is ideal for
natural and lively bass reproduction
•Subwoofer
The position of the subwoofer is not so critical, because low
bass sounds are not highly directional But it is better to
place the subwoofer neal the main speakers
TUlll it slightly
toward the centel
of the 100m to reduce the wallieflections
CAUTION
Some types
of speakers interfere with aTV monitor If
this problem occu!s, move the speakers away from the
monitO!
If you cannot avoid installing the center speaker
or subwoofer neal the
TV monitor, use magnetically
shielded speakers I
9
SPEAKER SETUP
Rear speaker (L)
Main speaker (R)
~,:
Refer to the following diagram when you place the
speakels
Main
speaker (L)
Center speaker
•Main speakers
Place the light and left main speakers an equal distance
from the ideal listening position The distance
of each
speaker from each side
of the TV monitor should be the
same
•Rear speakers
Place these speakels behind your listening position, facing
slightly inwards, neaI1y
18m (approx 6feet) above the
floO!
•If the cenler speakeI is not used, the centel channel sound will be
heatd flom the tight and left main speakels In that case,
"CENTER SP" on the SET MENU
is set to the NONE position
(Refet to page 36
fOJ details)
•Center speaker
Align the flOnt face of the center speaker with the flOnt face
of yoU! TV monitor Place the speaker as close to the
monitor
as possible, such as directly over or under the
monitol and centrally between the main speakers
The main speakels are used for the main soU!ce sound plus
the effect sounds They will probably be the speakels from
yoU! present stereo system The rear speakers are used for
the effect and surround sounds, and the center speaker
is for
the center sounds (dialog, vocals,
etc) If fO! some leason it
is not practical to use acenter speakel, you can do without
it Best results, however, are obtained with the full system
This unit is designed to provide the best sound-field quality
with a5-speaker system, using main speakers, rear speakels
and acenter speaker
If you use different brands of speakers
(with different tonal qualities) in your system, the tone
of a
moving human voice and other types
of sound may not shift
smoothly
We recommend that you use speakels from the
same manufacture
or speakers with the same tonal quality
The main speakers should be high-pelfO!mance models and
have enough power-handling capacity
to accept the
maximum output
of your audio system The other speakels
do not have to be equal to the main speakers For precise
sound localization, however, it is ideal
to use high-
performance models that can reproduce sounds ovel the full
range for the center speaker and the leal speakers
•Use of asubwoofer expands your
sound field
It is also possible to fU!ther expand yoU! system with the
addition
of asubwoofer The use of asubwoofer is effective
not only for reinforcing bass frequencies from any or all
channels, but also for replOducing the LFE (low frequency
effect) channel with high fidelity when playing back a
source encoded with Dolby Digital or DTS The YAMAHA
Active Servo Processing Subwoofer System
is ideal for
natural and lively bass reproduction
•Subwoofer
The position of the subwoofer is not so critical, because low
bass sounds are not highly directional But it is better to
place the subwoofer neal the main speakers
TUlll it slightly
toward the centel
of the 100m to reduce the wallieflections
CAUTION
Some types
of speakers interfere with aTV monitor If
this problem occu!s, move the speakers away from the
monitO!
If you cannot avoid installing the center speaker
or subwoofer neal the
TV monitor, use magnetically
shielded speakers I
9

CONNECTIONS
CAUTION
Never connect this unit and othel components to mains power until all connections between components have been
completed
Be sure all connections are made correctly, that
is to say L(left) to L, R(light) to R, "+" to "+" and "-" to "-" Some
components require different connection methods and have different terminal names Refer to the instructions for each
component to be connected to this unit
When you connect other YAMAHA audio components (such
as atape deck, MD recorder and CD player or changer), connect
it to the terminals with the same numbel labels as
[n W, @J etc YAMAHA applies this labeling system to all its products
Use RCA-type pin plug cables for connecting audio/video components with the exception described later
The input and output terminals for pin plugs can be distinguished as follows:
Yellow video signals (composite) ~
(SIJP
White analog audio signals
fOl the left channel .~
r:: Red analog audio signals fOl the Iight channel
=§IiII
coaxial digital signals c=§TIl Uill§=
After completing all connections, check them again to make sure they are correct
120VGOH,
100WMAX.TOTAl
SWITCHED
ACOlrTlJ;TS
IMPEDANCE SELECTOR
I SET BEFORE POWERQN t
W. .. AOR84llMINiSl'EAKER
AE:6IlMINISPEMER
REAR :511MINSPEAKER
CENTER :OllIdIN,·SPEMER
MA"'I~ORB_ 8ilMIN 'SPEAKER
18:!;;ll/,IINSPEAKEFl
REAR :1flII,lINSPEAKER
CENTER ;fIllMIIl.;SPEAKER
Connecting the Power
Supply Cords (page 18)
(U S A model)
Connecting the Speakers
(pages 16 and 17)
OUTPUT
MA!N
<90
®0 B
0Q 0\®J\®J0000
00 ®0 \®J \®J 0000 0
INIPLAY)OUT{FlE SUB
liJI TAI'ElMO WOOFEA
Connecting the Antenna Connecting to an External
(pages 11 and 12) Decoder (page 15)
Connecting an Audio
Component (page 13) Connecting aVideo Component (pages 14 and 15) IMPEDANCE SELECTOR switch (page 18)
10
CONNECTIONS
CAUTION
Never connect this unit and othel components to mains power until all connections between components have been
completed
Be sure all connections are made correctly, that
is to say L(left) to L, R(light) to R, "+" to "+" and "-" to "-" Some
components require different connection methods and have different terminal names Refer to the instructions for each
component to be connected to this unit
When you connect other YAMAHA audio components (such
as atape deck, MD recorder and CD player or changer), connect
it to the terminals with the same numbel labels as
[n W, @J etc YAMAHA applies this labeling system to all its products
Use RCA-type pin plug cables for connecting audio/video components with the exception described later
The input and output terminals for pin plugs can be distinguished as follows:
Yellow video signals (composite) ~
(SIJP
White analog audio signals
fOl the left channel .~
r:: Red analog audio signals fOl the Iight channel
=§IiII
coaxial digital signals c=§TIl Uill§=
After completing all connections, check them again to make sure they are correct
120VGOH,
100WMAX.TOTAl
SWITCHED
ACOlrTlJ;TS
IMPEDANCE SELECTOR
I SET BEFORE POWERQN t
W. .. AOR84llMINiSl'EAKER
AE:6IlMINISPEMER
REAR :511MINSPEAKER
CENTER :OllIdIN,·SPEMER
MA"'I~ORB_ 8ilMIN 'SPEAKER
18:!;;ll/,IINSPEAKEFl
REAR :1flII,lINSPEAKER
CENTER ;fIllMIIl.;SPEAKER
Connecting the Power
Supply Cords (page 18)
(U S A model)
Connecting the Speakers
(pages 16 and 17)
OUTPUT
MA!N
<90
®0 B
0Q 0\®J\®J0000
00 ®0 \®J \®J 0000 0
INIPLAY)OUT{FlE SUB
liJI TAI'ElMO WOOFEA
Connecting the Antenna Connecting to an External
(pages 11 and 12) Decoder (page 15)
Connecting an Audio
Component (page 13) Connecting aVideo Component (pages 14 and 15) IMPEDANCE SELECTOR switch (page 18)
10

CONNECTIONS
Both AM and FM indoor antennas ale included with this unit In geneial, these antennas should plOvide sufficient signal
sttength Howevet, apropetly installed outdoor antenna plOvides clealet teception than an indoot one
If you experience pOOt
reception quality, an outdoot antenna may implOve the quality
Connect each antenna conectly to the designated tetminals
•Indoor FM antenna (included)
•Use this adaptel to match
with F-type connectol
•Do not
connect an outdool FM antenna and the indoOl FM
antenna at the same tinlC
Fiunly insett the connectot into the FM ANT terminal The
indoor FM antenna
is only asimple antenna For reception
with better sound quality, installing the outdoor
FM antenna
(commetcially available)
is tecommended
You may be unable to obtain good FM radio reception
depending on yom local conditions (distance from the
blOadcasting station, interposing buildings and
mountains,
etc) Consult your dealer 01 authotized setvice
centet and be SUleto install
an antenna that suits your local
conditions
Install the
outdOOl FM antenna (commercially available) in
ahigh place
as fat away flOm any lOads as possible to avoid
being affected
by automobile ignition noise
A
iI
Indoor FM
antenna
1
1
75-ohm coaxial cable 1
I
1
1
[11 ,- -7~-~h';;f;;O:o-h~-a~;e~~a- - - __ I
--r adapter
1
1
,-----
U
--- .~
+ ... r
! Ant~nna adapter
'.. (included for USA and
.Canada models)
I
•Outdoor FM antenna
I
11
CONNECTIONS
Both AM and FM indoor antennas ale included with this unit In geneial, these antennas should plOvide sufficient signal
sttength Howevet, apropetly installed outdoor antenna plOvides clealet teception than an indoot one
If you experience pOOt
reception quality, an outdoot antenna may implOve the quality
Connect each antenna conectly to the designated tetminals
•Indoor FM antenna (included)
•Use this adaptel to match
with F-type connectol
•Do not
connect an outdool FM antenna and the indoOl FM
antenna at the same tinlC
Fiunly insett the connectot into the FM ANT terminal The
indoor FM antenna
is only asimple antenna For reception
with better sound quality, installing the outdoor
FM antenna
(commetcially available)
is tecommended
You may be unable to obtain good FM radio reception
depending on yom local conditions (distance from the
blOadcasting station, interposing buildings and
mountains,
etc) Consult your dealer 01 authotized setvice
centet and be SUleto install
an antenna that suits your local
conditions
Install the
outdOOl FM antenna (commercially available) in
ahigh place
as fat away flOm any lOads as possible to avoid
being affected
by automobile ignition noise
A
iI
Indoor FM
antenna
1
1
75-ohm coaxial cable 1
I
1
1
[11 ,- -7~-~h';;f;;O:o-h~-a~;e~~a- - - __ I
--r adapter
1
1
,-----
U
--- .~
+ ... r
! Ant~nna adapter
'.. (included for USA and
.Canada models)
I
•Outdoor FM antenna
I
11

CONNECTIONS
• AM loop antenna (included)
AM loop antenna
o
I
1:
'N; II.III--------~
The AM loop antenna can be removed from the stand and
attached to awall, etc However, note that the reception
sensitivity may deteriorate
if the antenna is attached to a
metal or steel reinforced wall
• 'J he AM loop antenna should be placed away flOm this unit
•The AM loop antenna should always be connected, even if an
outdOOl AM antenna is connected to this unit
•Connecting the AM loop antenna oPress the tab and unlock the terminal hole.
~Insert the AM loop antenna lead wires into the
AM ANT and GND terminals.
oAttach the loop antenna to the antenna stand.
mOrient the AM loop antenna so that the best
reception is obtained.
!J Return the tab to its original position to lock
the lead wires. Lightly pull the lead wires
to
confirm agood connection.
5
4
+~
Antenna stand
•Outdoor AM antenna
Vinyl covered wire (5 m to 10 m)
o
-------_ ..
I
--------,
If you cannot obtain good reception with the AM loop
antenna, connect 5 m to
10 m of vinyl covered wire to the
AM ANT terminal and extend it outdoors from awindow
•Ground (GND terminal)
------------,I
a
~
~
For maximum safety and minimum interference, connect
the antenna GND terminal to agood earth ground Agood
eatth glOund
is ametal stake driven into moist earth
12
CONNECTIONS
• AM loop antenna (included)
AM loop antenna
o
I
1:
'N; II.III--------~
The AM loop antenna can be removed from the stand and
attached to awall, etc However, note that the reception
sensitivity may deteriorate
if the antenna is attached to a
metal or steel reinforced wall
• 'J he AM loop antenna should be placed away flOm this unit
•The AM loop antenna should always be connected, even if an
outdOOl AM antenna is connected to this unit
•Connecting the AM loop antenna oPress the tab and unlock the terminal hole.
~Insert the AM loop antenna lead wires into the
AM ANT and GND terminals.
oAttach the loop antenna to the antenna stand.
mOrient the AM loop antenna so that the best
reception is obtained.
!J Return the tab to its original position to lock
the lead wires. Lightly pull the lead wires
to
confirm agood connection.
5
4
+~
Antenna stand
•Outdoor AM antenna
Vinyl covered wire (5 m to 10 m)
o
-------_ ..
I
--------,
If you cannot obtain good reception with the AM loop
antenna, connect 5 m to
10 m of vinyl covered wire to the
AM ANT terminal and extend it outdoors from awindow
•Ground (GND terminal)
------------,I
a
~
~
For maximum safety and minimum interference, connect
the antenna GND terminal to agood earth ground Agood
eatth glOund
is ametal stake driven into moist earth
12

CONNECTIONS
Turntable
CD player
© ~ © ~
Jii'i~~.;.1 "F, "
~,-,-""-",,,,~,,~:,
Tape deck or
MD recorder
Analog signal
Signal flow
Be sure to connect the light channel (R), left channel (L),
input (IN) and output (OUT) properly •PHONO terminals
These terminals ale used to connect aturntable with an MM
or high-output MC cartridge If you have aturntable with a
low-output MC cartridge, use an inline boosting tJansfolmer
01 MC head amplifier when connecting to these telminals
'"
~(j)-:'
Connecting the glOund (emth) wile of the tlllntable to the GND
tellninal will nOllnally minimize hum, but in some cases, bette!
lesults may be obtained with the glOund wire disconnected
I
13
CONNECTIONS
Turntable
CD player
© ~ © ~
Jii'i~~.;.1 "F, "
~,-,-""-",,,,~,,~:,
Tape deck or
MD recorder
Analog signal
Signal flow
Be sure to connect the light channel (R), left channel (L),
input (IN) and output (OUT) properly •PHONO terminals
These terminals ale used to connect aturntable with an MM
or high-output MC cartridge If you have aturntable with a
low-output MC cartridge, use an inline boosting tJansfolmer
01 MC head amplifier when connecting to these telminals
'"
~(j)-:'
Connecting the glOund (emth) wile of the tlllntable to the GND
tellninal will nOllnally minimize hum, but in some cases, bette!
lesults may be obtained with the glOund wire disconnected
I
13

CONNECTIONS
Analog signal
QSlJ\::= SVideo signal
;:(9]}o __ ,Digital signal
(optical)
~ _. Digital signal
(coaxial)
-+- Signal flow
Cable TV Isatellite tuner
I
@VCR
I
J,..
IOPTICAL
IDIGITAL OUT
--,
,-----------
I ,---
ICOAXIAL IOPTICAL
+DIGITAL OUT +oIGITAL OUT
II
~ ~
I I
I I
I I
-----------------; I
I
------,
~ COAXIAL :OPTICAL
IDIGITAL OUT IDIGITAL OUT
... ...
I I
, ~
I
I I
"'--------~
D
DVD/LD player
~ ~J
,.. )1""
SVIDEO ANALOG
OUT AUDIO OUT
TV monitor
(U S A model)
TV/digital TV
•Audio signal terminals
Be sure to connect the right channel (R), left channel (L),
input (IN) and output (OUT) properly
•SVideo signal terminals
Use aspecial SVIDEO cable (commercially available) for
the SVIDEO connection
•Digital audio signal terminals
If your DVDILD player, TVIdigital TV OJ cable TVIsatellite
tuner, etc has coaxial or optical digital signal output
telminals, they can be connected to this unit's COAXIAL
and/or OPTICAL digital signal input terminals
To make a
connection between the optical digital signal terminals,
remove the covel from each terminal, and then connect
them by using acommercially available optical fiber cable
that conforms to EIA standards Othel cables might not
function correctly
•Be SUle to attach the covers when the OPTICAL telminals are not
being used in Oldel to plOtect them
flOm dust
•
If YOUl LD playel has aDolby Digital RF signal output tel minai,
be
SUle to use the RF demodulatOl (sepmately pUlchased)
•No sound will be hemd when connecting
YOUl LD playel's Dolby
Digital
RF signal output telminal dilectly to this unit's COAXIAL
DVD/LD digital signal input telminal
'"
'::$':.
•The input signal flOm the DVD/LD Ol CBL/SAT input terminals
is selected in the following ordel
of pliOlity with the input mode
set to AUTO:
COAXIAL telll1inal -j OPTICAL telminal -j
Analog telll1inal Refel to page 23 fOl details
•All digital signal input telminals me applicable to sampling
flequencies
of 32 kHz, 44 IkHz, 48 kHz and 96 kHz (Refel to
page 24 about 96-kHz sampling 24-bit digital
signals)
When making connections between the digital signal
terminals, you should connect the components
to the same-
named analog audio signal terminals
of this unit, because a
digital signal cannot be recorded by atape deck, MD
recorder or VCR connected to this unit
14
CONNECTIONS
Analog signal
QSlJ\::= SVideo signal
;:(9]}o __ ,Digital signal
(optical)
~ _. Digital signal
(coaxial)
-+- Signal flow
Cable TV Isatellite tuner
I
@VCR
I
J,..
IOPTICAL
IDIGITAL OUT
--,
,-----------
I ,---
ICOAXIAL IOPTICAL
+DIGITAL OUT +oIGITAL OUT
II
~ ~
I I
I I
I I
-----------------; I
I
------,
~ COAXIAL :OPTICAL
IDIGITAL OUT IDIGITAL OUT
... ...
I I
, ~
I
I I
"'--------~
D
DVD/LD player
~ ~J
,.. )1""
SVIDEO ANALOG
OUT AUDIO OUT
TV monitor
(U S A model)
TV/digital TV
•Audio signal terminals
Be sure to connect the right channel (R), left channel (L),
input (IN) and output (OUT) properly
•SVideo signal terminals
Use aspecial SVIDEO cable (commercially available) for
the SVIDEO connection
•Digital audio signal terminals
If your DVDILD player, TVIdigital TV OJ cable TVIsatellite
tuner, etc has coaxial or optical digital signal output
telminals, they can be connected to this unit's COAXIAL
and/or OPTICAL digital signal input terminals
To make a
connection between the optical digital signal terminals,
remove the covel from each terminal, and then connect
them by using acommercially available optical fiber cable
that conforms to EIA standards Othel cables might not
function correctly
•Be SUle to attach the covers when the OPTICAL telminals are not
being used in Oldel to plOtect them
flOm dust
•
If YOUl LD playel has aDolby Digital RF signal output tel minai,
be
SUle to use the RF demodulatOl (sepmately pUlchased)
•No sound will be hemd when connecting
YOUl LD playel's Dolby
Digital
RF signal output telminal dilectly to this unit's COAXIAL
DVD/LD digital signal input telminal
'"
'::$':.
•The input signal flOm the DVD/LD Ol CBL/SAT input terminals
is selected in the following ordel
of pliOlity with the input mode
set to AUTO:
COAXIAL telll1inal -j OPTICAL telminal -j
Analog telll1inal Refel to page 23 fOl details
•All digital signal input telminals me applicable to sampling
flequencies
of 32 kHz, 44 IkHz, 48 kHz and 96 kHz (Refel to
page 24 about 96-kHz sampling 24-bit digital
signals)
When making connections between the digital signal
terminals, you should connect the components
to the same-
named analog audio signal terminals
of this unit, because a
digital signal cannot be recorded by atape deck, MD
recorder or VCR connected to this unit
14

CONNECTIONS
-+- Signal flow
•If video signals ale input flom both the SVIDEO input and
composite input telminals, the signals will be dilected to their
lespective output telminals
If your video components do not have "S" video terminals,
they can be connected to this unit's VIDEO terminals Be
sure
to connect the input (IN) and output (OUT) properly
VIDEO VIDEO
OUT IN
CableTV/satellite tuner
~¥,o;:;~",
~
TV monitor TV/digital TV
~ Video signal
DD
•VIDEO terminals (composite)
DVD/LD player
r';'l:Poo",
~
These telminals are used to connect any video input source
such
as acamcorder to this unit
Camcorder
[c;1 ~)
AUDIOOUTR
AUDIOOUTL
•VIDEO AUX terminals (on the front panel)
--V'OEOAUX-
O~~~
, I'~ , '0
External decoder
(U S A model)
This unit has additional 6-channel audio signal input
terminals for connecting an external decoder to this unit
Connect the 6-channel audio signal output terminals
of the
decoder to the EXTERNAL DECODER INPUT terminals
of this unit
•When asoUtce connected to these telminals is selected, the digital
sound field
plOceSSot cannot be used
•The settings
of "CENTER SP", "REAR SP", "MAIN SP" and
"BASS OUT" on the SET MENU have no effect on asource
connected to these telminals The setting
of "MAIN LVL" is
effective (Refet to pages 36 and 37
fot details)
•Adjustment of the output level of the centel speaker, leal speakels
and subwoofel
is effective when a SOUlce connected to these
tellninals
is selected as the input soutce (Refel to page 39 fot
details)
I
15
CONNECTIONS
-+- Signal flow
•If video signals ale input flom both the SVIDEO input and
composite input telminals, the signals will be dilected to their
lespective output telminals
If your video components do not have "S" video terminals,
they can be connected to this unit's VIDEO terminals Be
sure
to connect the input (IN) and output (OUT) properly
VIDEO VIDEO
OUT IN
CableTV/satellite tuner
~¥,o;:;~",
~
TV monitor TV/digital TV
~ Video signal
DD
•VIDEO terminals (composite)
DVD/LD player
r';'l:Poo",
~
These telminals are used to connect any video input source
such
as acamcorder to this unit
Camcorder
[c;1 ~)
AUDIOOUTR
AUDIOOUTL
•VIDEO AUX terminals (on the front panel)
--V'OEOAUX-
O~~~
, I'~ , '0
External decoder
(U S A model)
This unit has additional 6-channel audio signal input
terminals for connecting an external decoder to this unit
Connect the 6-channel audio signal output terminals
of the
decoder to the EXTERNAL DECODER INPUT terminals
of this unit
•When asoUtce connected to these telminals is selected, the digital
sound field
plOceSSot cannot be used
•The settings
of "CENTER SP", "REAR SP", "MAIN SP" and
"BASS OUT" on the SET MENU have no effect on asource
connected to these telminals The setting
of "MAIN LVL" is
effective (Refet to pages 36 and 37
fot details)
•Adjustment of the output level of the centel speaker, leal speakels
and subwoofel
is effective when a SOUlce connected to these
tellninals
is selected as the input soutce (Refel to page 39 fot
details)
I
15

CONNECTIONS
Main speakers A
Subwoofer connection
When using asubwoofet with built-
in amplifier, including the
YAMAHA Active Servo Processing
Subwoofer System, connect the
input tet minal
of the subwoofer
system to the SUBWOOFER
OUTPUT terminal
of this unit
Low bass signals distributed
flOm
the main, center and/or tear
channels are directed to this
tetminal (The cut-offtiequency
of
this terminals is 90 Hz )The LFE
(low ftequency effect) signals
generated when Dolby Digital OJ
DTS is decoded are also ditected if
they are assigned to this terminal
Main speakers B
Subwoofer
system Center speaker Rear speakers
Be sure to connect the right channel (R), left channel (L),
"+" (red) and "-" (black) properly If the connections are
faulty, no sound will be heard from the speakers, and
if the
polarity
of the speaker connections is incorrect, the sound
will be unnatural and lack bass
CAUTIONS
•Use speakers with the specified impedance shown on
the rear panel
of this unit
•Do not let the bare speaker wires touch each other and
do not let them touch any metal part
of this unit This
could damage the unit and/or speakers
16
•MAIN SPEAKERS terminals
One or two speaker systems can be connected to these
terminals
If you use only one speaker system, connect it to
either of the SPEAKERS A or Bterminals
•REAR SPEAKERS terminals
Arear speaker system can be connected to these terminals
•CENTER SPEAKER terminals
Acenter speaker can be connected to these terminals
CONNECTIONS
Main speakers A
Subwoofer connection
When using asubwoofet with built-
in amplifier, including the
YAMAHA Active Servo Processing
Subwoofer System, connect the
input tet minal
of the subwoofer
system to the SUBWOOFER
OUTPUT terminal
of this unit
Low bass signals distributed
flOm
the main, center and/or tear
channels are directed to this
tetminal (The cut-offtiequency
of
this terminals is 90 Hz )The LFE
(low ftequency effect) signals
generated when Dolby Digital OJ
DTS is decoded are also ditected if
they are assigned to this terminal
Main speakers B
Subwoofer
system Center speaker Rear speakers
Be sure to connect the right channel (R), left channel (L),
"+" (red) and "-" (black) properly If the connections are
faulty, no sound will be heard from the speakers, and
if the
polarity
of the speaker connections is incorrect, the sound
will be unnatural and lack bass
CAUTIONS
•Use speakers with the specified impedance shown on
the rear panel
of this unit
•Do not let the bare speaker wires touch each other and
do not let them touch any metal part
of this unit This
could damage the unit and/or speakers
16
•MAIN SPEAKERS terminals
One or two speaker systems can be connected to these
terminals
If you use only one speaker system, connect it to
either of the SPEAKERS A or Bterminals
•REAR SPEAKERS terminals
Arear speaker system can be connected to these terminals
•CENTER SPEAKER terminals
Acenter speaker can be connected to these terminals