Yamakin Luna-Wing User manual

INT 20130111
Certification Number
Controlled Medical Devices
Light Cure Composite Resin for Crows and Bridges
Instructions Manual
Yamamoto Precious Metal Co., Ltd.
Please read through this manual
before using the product.

1
Warning
Warning
Warning
Luna-Wing strikes a good balance between excellent properties and easy handling, with filler
developed by nanotechnology. Biological safety tests based on global standard ISO 10993 “Biological
evaluation of medical devices” have been conducted on Luna-Wing. Also, our company’s original
biogenetic evaluation tests on cell, tissue have also revealed further details of the effect Luna-Wing
in the mouth.
[ Contraindications and Prohibitions ］
Do not use this product on patients who have a history of allergy (such as irritation ) to
this product or methacryl monomer.
[ Shapes, Composition and Principles ］
This product consists of the following items and contains ingredients below.
Principles: This material is a light-cure type, cured by visible light.
[ N.B.:Technical Directions and Points for Attention ］
1. For light-curing this product, use a halogen lamp, xenon lamp, metal halide lamp or LED with an
effective wavelength of 400-500 nano-meters.
In cases where other medical curing equipment is to be used, or if you have any questions about
curing machines, please feel free to contact us.
2. As fractures may happen, this product cannot be used for molars.
3. In cases where this product is used for anterior tooth and facing crown, the occlusal area of the
opposing tooth must be metal-coated to avoid fracture.
4. Close the cap promptly and tightly after using this product.
5. Use separate brushes for primer paste, opaque, stain, and repair liquid.
6. When in use on a pallet or mixing paper, this product should be covered by a shade cover.
7. Do not mix body resin with other materials, and do not mix more than one type of body resin to
prevent air bubble entrapping and deterioration in quality of material properties.
8. Stain must be applied on internal layer; please use Enamel or other products after Stain application.
9. Avoid exposures to strong light or sunlight ( near windows or laboratory lights, etc. ) in order to
prevent hardening of paste.
10. Do not use base on facing part, as base is designed only for the pontic area.
Controlled Medical Devices
Light Cure Composite Resin for Crowns and Bridges
Luna-Wing
Table of Contents
2
2 Contraindications and Prohibitions
2 Shapes, Composition and Principles
2 N.B.: Technical Directions and Points for Attention
3 Precautions
1. Precautions
2. Important Basic Cautions
3. Other Cautions
3 Handling, Storage and Expiry Date
1. Handling and Storage
2. Expiry Date
4 Intended use and effect / efficacy
4 Characteristics
1. Safety
2. Properties
3. Handling
4. Colors
5-6 Luna-Wing Shade Color Table
7 Luna-Wing Compositions
1. Primer Paste
2. Opaque Resin
3. Body Resin
4. Stain
5. Repair Liquid
7-8 Instructions for Use
1. Primer Paste
2.1 Invisible Opaque
2.2 Opaque
2.3 Special Opaque Color
3.1 Opaque Dentine
3.2 Cervical
3.3 Dentine
3.4 Enamel
3.5 Trans Enamel
3.6 Translucent
3.7 Effect
3.8 Base
4. Stain
5. Repair Liquid
9 Light Curing Schedule
9 Basic Layering Technique
10 Luna-Wing Basic Layering Step
11-21 Basic Layering Technique
Basic Build-Up Layering for Facing Crown
Basic Build-Up Layering for Crown Bridge
Basic Build-Up Layering for Jacket Crown
22 Line Up
Item
Opaque Resin metacrylate monomer, inorganic fillers, pigments, etc.
metacrylate monomer, organic fillers, inorganic fillers, pigments, etc.
Body Resin
metacrylate monomer, inorganic fillers, pigments, etc.
Stain
metacrylate monomer, etc.
Repair Liquid
Silane Coupling Agent, etc.
Primer Paste
Paste
Paste
Paste/Liquid
Liquid
Paste
State Ingredients

3 4
[ Precautions ］
1. Precautions
① Provide adequate ventilation (several times per hour ).
② When cutting and polishing cured product, use exhaust fan and anti-dust mask as approved by your
local public safety agency in order to avoid inhaling dust. Wear safety goggles to protect the eyes.
③ Do not use this product outside the scope of recommended indications, effects or potency.
④ Do not use this product in combination with other products.
⑤ Only adequately certified personnel should handle this product.
⑥ Do not loosen or screw the syringe at low temperature as it may break. Please use this product at
an ambient temperature of around 20℃. For example, in cases where the product has been
stored at 4℃, leave it at a room temperature of around 20℃ for more than 20 min. in order to
prepare product for use. 20℃-25℃ is the optimal temperature for easy handling.
2. Important Basic Cautions
① Stop using this product immediately if any signs of allergy, such as irritation or rush, appears in
patients. If symptoms persist, seek medical advice.
② Operators must discontinue use if any signs of irritation or rash appear. If symptoms persist, seek
medical attention.
③ Do not handle non-cured material of this product with bare hands. Wear plastic gloves and safety
goggles to protect from irritation. Avoid direct skin and eye contact. In case of skin contact, wipe
with alcohol cotton swabs, and flush with plenty of running water. In case of eye contact,
immediately flush with plenty of running water, and consult a physician.
3. Other Cautions
Crown restoration area may be stained and plaque-adherent depending on patients’ dietary habits.
Advise daily oral cleaning.
[ Handling, Storage and Expiry Date ］
1. Handling and Storage
① This product must be stored in out of contact with direct light sources at a temperature of 4-25℃.
② Do not store too many products in the same storage area.
③ Storage and working areas must be equipped with fire extinguisher.
④ Keep out of reach of personnel other than dental staff.
2. Expiry Date
① This product must be used before the expiry date printed on the package.
② The expiry date printed on the package is based on our authentication.
③ The expiry date printed on the package refers to use the expiry date.
*(ex.; YYYY-MM means the last day of YYYY ’year’/MM ’month’ as the expiry date)
[ Intended use and effect / efficacy ］
This product is a light-cure type composite resin for dental crown restoration and temporary
crowns, such as facing crowns, jacket crowns, and bridges. Do not use this product for other
purposes.
[ Product Specification ］
This product is a light-cure type composite resin
for dental crowns and bridges classified as
ISO 10477, Dentistry-polymer-based crown and
bridge materials that contain a light or
UV-sensitive initiator;Type 2, Class 2
[ Characteristics ］
1. Safety
This product conforms to ISO 10993-1 and biocompatibility has been confirmed through evaluation
testing. This product has also passed our own biological safety tests based on biogenetic, cell and
tissue evaluation.
2. Properties
Fillers’ particle size is well-adjusted, and fillers are formulated with high density and good balance.
Properties such as bending strength, hardness and abrasion resistance are improved by strengthening
the bonding between matrix and fillers. Fillers’ high filling rate works to decrease cure shrinkage,
prevents cracks and improves fitting accuracy. In the mouth, the degree of abrasion by brushing is
decreased and luster is long-lasting.
3. Handling
The Opaque resin line-up includes highly flowable Invisible Opaque, which flows into the undercut of
retention beads evenly. With Opaque, light curing is secured with a deep light cure depth.
Luna-Wing Body resin paste is such an easy molding material that it maintains its form without
dripping off during the forming process. Enamel, Trans Enamel, Translucent, Effect and Base prevent
air bubble formation by having a viscosity 30% lower than Cervical, Opaque Dentine and Dentine.
Also, we have lineup of hard type of Enamel, Trans Enamel and Translucent, and their consistency
(viscosity) is same as Dentine.
4. Colors
Luna-Wing reproduces the colors of general-use shade guides. For frequently used A2, A3, and A3.5
shades, Red Plus Shade is available to increase redness in the mouth. Red Plus Shade reproduces
the typical redness and brightness of Japanese teeth. In cases where sufficient thickness is not
secured, apply Opaque Dentine thinly to reproduce color easily. The Opaque Dentine shade lineup is
available in the A series only. There are a variety of characterizing colors, such as Effect and Stain,
which work effectively to make partial accents. Furthermore, Luna-Wing has fluorescence similar to
natural teeth for even more beautiful restoration.
Warning
Warning
Hardness(HV) 59
Flexural Strength(MPa) 116
Water Sorption(μg/mm3)29
1.0
Solubility (μg/mm3)
Body Resin
(Standard)
59
105
28
0.9
Hard Type*
* We have lineup of hard type of Enamel, Trans Enamel
and Translucent, and their viscosity is same as Dentine.

5 6
[ Luna-Wing Shade Color Table ］
■ Basic Shades
TE
■ Trans Enamel
OA3.5 OA4OA0 OA1 OA2 OA3
A0 A1 A2 A3 A3.5 A4
CA1 CA2
DA3.5 DA4DA0 DA1 DA2 DA3
E0 E2 E3 E4
ODA3.5 ODA4ODA0 ODA1 ODA2 ODA3
OB1 OB2 OB3 OB4 OC1 OC2 OC3 OC4 OD2 OD3 OD4
IvO
B1 B2 B3 B4 C1 C2 C3 C4 D2 D3 D4
CC1 CC2 CD1 CD2CB1 CB2
DB1 DB2 DB3 DB4 DC1 DC2 DC3 DC4 DD2 DD3 DD4
E1
Invisible Opaque
Opaque
Cervical
Opaque Dentine
Dentine
Enamel
E2 E2E2E3 E3 E3E4
■ Base
Base
■ Effect
HV WE WE AM OC Coffee Orange L GUM GUM D GUM
■ Stain
Milky Pink Salmon Pink White Violet Violet Orange Dark Orange RedWhite
Mky Pnk S Pn k W V l t Vlt Org Dk Org RedWht
ClearGray Black
ClearGry Bl k
Dark Brown A Shift B Shift C Shift D Shift Reb Brown
R Brn
Yellow
Yel
Blue
Blu
Brown
Brn Dk Brn A Sft B Sft C Sft D Sft
■ Special Opaque Color
InO1 InO2 PO MO
■ Translucent
HVT T LVT C T
■ Red Plus Shade
Opaque
Cervical
Dentine
CA2 RCA1 R
DA2 R DA3 R DA3.5 R
OA2 R OA3 R OA3.5 R
*We also have Lineup of hard type of Enamel, Trans Enamel and Translucent.
Enamel : E0 Hard, E1 Hard, E2 Hard, E3 Hard, E4 Hard
Trans Enamel : TE Hard
Translucent : HVT Hard, T Hard, LVT Hard, CT Hard

7 8
* Base has deep cure depth, and was developed exclusively
for pontic cutback with improved hardness. It cannot be
used on front, as other types of body resin can.
Incisal Opaque
In01 (gray), In02 (gray, purple); Basic color to give artificial translucency
to connector of connected teeth and anterior incisal edge (when there is
metal close to incisal edge).
Margin Opaque Orange and beige color to emphasize cervical color.
InO1
InO2
MO
Basic color for gum color resin.
PO Pink Opaque
Expresses orange clearness.
AM Amber
Light orange color. Expresses color of posterior occusal surface.
OC Occlusal
Emphasizes brown colors such as coffee.
Coffee Coffee
Dark gum color to express gum.
Emphasizes orange color.
Orange Orange
Enamel with High brightness. Expresses proximal surface and white bands.
WE White Enamel
D GUM
Normal gum color to express gum.
GUM Gum
Expresses light gum color.
L GUM Light Gum
Dark Gum
HVWE High Value White Enamel Enamel brighter than WE.
HVT High Value Translucent Translucent with high brightness.
TTranslucent Standard translucent.
LTV Low Value Translucent Translucent with low brightness.
CT Cervical Translucent Light orange and pink translucent for gum color.
For cervical area expression.
[ Luna-Wing Composition ］
[ Instructions for Use ］
1. Primer Paste
Apply before Invisible Opaque for surface treatment. Primer paste has strong bonding to
non-precious alloys. It can be used as Invisible Opaque, so the use of Invisible Opaque is not
necessary. In this case, Primer Paste should be applied thickly enough to cover retention beads.
※Primer Paste can not be used for gold alloys.
2.1 Invisible Opaque
Invisible Opaque is a flowable opaque resin that flows into the undercut of retention beads to
enhance mechanical retention between metal and resin.
2.2 Opaque
Opaque is used to cover metal color.
2.3 Special Opaque Color
This Opaque is used for natural color expression. Use on incisal or cervical area when reflection
of Opaque color is strong.
3.1 Opaque Dentine
Opaque Dentine is used to prevent percolation of opaque color ( when there is an extremely thin
space for build-up )(when sufficient thickness for Dentine is not secured ). When build-up thickness
is less than 0.5mm, apply it thinly to express color depth with a thin layer.
3.2 Cervical
Body resin for natural color expression around cervical area.
3.3 Dentine
Body resin to express dentine.
3.4 Enamel
Body resin to express enamel.
3.5 Trans Enamel
Body resin to express translucency.
It’s used to express translucency is between Translucent and Enamel.
3.6 Translucent
Body resin to express translucency.
3.7 Effect
Characterizing body resin to express discolored tooth, etc.
3.8 Base
Base is used to fill pontic part of bridges.
Base is translucent color with deep light-cure depth, designed only for pontic part.
It cannot be used on facing part.
4. Stain
Characterizing item to express discolored tooth. Additional color tone is expressed effectively by
thin layer. After light curing of opaque or body resin, apply with a round brush and light cure for
about 60 sec.
Stain should be used as an internal color expression. After applying stain, light cure for about 60
sec.; it is necessary to apply body resin afterward.
* Stain cannot be used for surface.
All “shift” stains are basically brown colors adjusted to general shades from A to D.
There are 4 kinds of shift: A shift (red and brown), B shift (red and yellow), C shift (gray), and D
shift (red and gray).
Clear is dilute liquid to adjust viscosity of Stain. Clear can be used to emphasize translucency.
5. Repair Liquid
Repair Liquid is used when non-cured surface is removed after correction of shape.
It improves the adaptation of cured surface before additional application.
1. Primer Paste
Primer Paste is a bonding primer for non-precious
alloys. It cannot be used on gold alloys.
4. Stain
Light-cure type paste containing methacryl
monomer for color adjustment.
‘Clear’ is a diluent liquid for Stain, and also is
applicable to emphasize translucency.
5. Repair Liquid
Light-cure type liquid containing methacryl
monomer. For additional build-up after shape
adjustment, apply Repair Liquid thinly then apply
body resin. It improves adaptability of hardened
surface.
3. Body Resin
Light-cure type paste containing methacryl
monomer. Body resin is a generic term for
Opaque Dentine, Cervical, Dentine, Enamel,
Trans Enamel, Translucent, and Effect.
2. Opaque Resin
Light-cure type paste containing methacryl
monomer intended to conceal metal color.
Apply Invisible Opaque first to seal undercut
retention beads, and then light cure. Then, apply
each opaque and light cure.

9 10
E3
OA3
IvO
DA3
E3
IvO
DA3
T
CA1
OA3
Multi-layer build-up
Invisible Opaque
Primer Paste
Name
Conventional
Curing Time
（Seconds）
Yamakin
LED CURE Master
About 90 sec.
About 90 sec.
About 180 sec.
About 180 sec.
About 60 sec.
About 60 sec.
About 180 sec.
About 10 sec.
About 10 sec.
About 30 sec.
About 90 sec.
About 10 sec.
About 10 sec.
About 90 sec.
Stain
Final Light Cure
Opaque
Base
Others
Body Resin*
[ Light Curing Schedule ］
[ Basic Layering Technique ］
[ Luna Wing Basic Layering Step ］
Curing procedure is as
given in the table.
Final Light Cure：light
cure after finishing the
build-up completely.
*Body Resin
Cervical, Opaque
Dentine,
Dentine, Enamel,
Translucent Enamel
Translucent, Effect,
Base
2-layer build-up
Almina particle size: about 50μm
Pressure: about 0.2～0.25Mpa *TWiNY Resin Spacer
*TWiNY Resin Separator
*Apply Primer Paste and leave
it for 120sec.,then light cure
[about 90sec.] [LED:about 10sec.]
[about 180sec.] [LED:about 90sec.]
Correction to Shape & Polish
Final light curing
Internal Treatment
COMPLETE
Jacket CrownFacing Crown
*Apply Invisible Opaque to covering
a top of retention beads., then light cure
[about 90sec.] [LED:about 10sec.]
Stain & light cure
Characterize on body resin
*Stain cannot be used for surface.
[about 60sec.] [LED:about 10sec.]
Body & light cure
Repeat Opaque process until the metal
color is concealed., then light cure
[about 180sec.] [LED: 30sec.]
・Sand-blasting (about0.1～0.2Mpa) the
inside of the jacket crown using alumina
powder(about 50μm)
・Steam cleaning or ultrasonic cleaning
Special Opaque Color & light cure
Characterize on Opaque
[about 180sec.] [LED:about 30sec.]
[about 180sec.] [LED: 90sec.]
Opaque & light cure
Apply Separator
Primer Paste & light cure
Invisible Opaque & light cure
Base on pontic & light cure
Secure cement paste
Plaster modeling
Almina sandblasting
Metal frame preparation
Body (Cervical, Dentine & Enamel) & light cure
[about 60sec.] [LED:about 10sec.]
[about 60sec.] [LED:about 10sec.]

11 12
Forming Examples
6. Dentine Application and Light Curing
Apply Dentine to form the required dentine core
shape and light cure for about 60 sec.
(Apply desired color of Stain with round brush if
necessary to adjust color tone and for partial
characterization. Then light cure for about 60
sec.)
*When non-cured surface is removed after
correction of shape, use Repair Liquid.
It improves the adaptation of cured surface
before additional application
7. Enamel Application and Light Curing
Apply Enamel to form the required crown shape
and light cure for about 60 sec.
2. Alumina Treatment of Metal Frame
Sand-blast (about 0.2～0.25Mpa ) the surface with
alumina powder (about 50μm ) ;then use steam
cleaner or ultrasonic cleaner to wash, then dry.
1. Metal Frame Preparation
Make a plaster model in accordance with normal
practice. Make the crown shape using wax, and
make space between crowns; then apply
bonding material and retention beads on facing
part to make wax pattern (mould of metal
frame ). Use 100μm-200μm particle size
retention beads.
Then cast the metal following product instruction.
*Conventional curing time is indicated in the following steps.
In case, the LED CURE Master is used, please confirm "Light Curing Schedule" on pade 9.
Make metal frame
Almina treatment of metal frame
Apply and dry primer
4. Opaque Application and Light Curing
Apply opaque with a flat brush thinly and light
cure for about 180 sec. In cases where the
metal color is visible, repeat this step until the
metal color is concealed.
*Do not apply thickly at one time.
Use Special Opaque Color to express
transparency of the incisal area or color of the
neck.
Apply and light cure opaque
5. Cervical (Opaque Dentine) Application
and Light Curing
Apply Cervical or Opaque Dentine starting from
the neck to the incisal area, applying
progressively thinner, taking subsequent color
gradation into consideration. Light cure for about
60 sec.
Form and Light Cure Body Resin
3. Primer Paste and Invisible Opaque
Application and Light Curing
Apply Primer Paste evenly with a flat brush.
Leave it for 120 sec., to enhance bonding
strength. Light cure for about 90sec.Then apply
Invisible Opaque to cover retention beads. Apply
thinly in margin area with no beads. Light cure
about 90 sec. again. Primer Paste is a bonding
material, but at the same time it can be used as
Invisible Opaque, the use of Invisible Opaque is
not necessary. In this case, Primer Paste should
be applied thickly enough to cover retention
beads.
*Primer Paste can not be used for gold alloys.
Apply and light cure Invisible Opaque
[ Basic Build-Up Layering for Facing Crown ］
Facing Crown

12. Polishing
Polish by using brush, fabric buff, with C&B
Diamond polisher or C&B Nano Diamond Polisher.
13 14
8. Translucent Application and Light
Curing
In cases where Translucent is required, apply
Translucent and light cure for about 60 sec.
11. Finishing
Remove any scars with paper cone and silicon
point to make the surface smooth.
13. Complete
Finish
[ Basic Build-Up Layering for Facing Crown ］
Facing Crown
Forming Examples
Final Light Cure
9. Final Light Curing
After final layering, light Cure for about 180 sec
as a final light curing.
Figure Adjustment 10. Correction to Shape
Correct the shape using a carborundum or
diamond point.
*Additional Layering
In case of additional layering after corrections to
shape, apply Repair Liquid thinly and apply
needed body resin. Light cure for 60 sec., the
same steps as 5-9.
*Conventional curing time is indicated in the following steps.
In case, the LED CURE Master is used, please confirm "Light Curing Schedule" on pade 9.

15 16
2. Apply Retention Beads
Apply bonding material and retention beads on
facing part to make wax pattern.
Use 100μm -200μm particle size retention beads.
Then cast the metal following product instructions.
2. Primer Paste and Invisible Opaque
Application and Light Curing
Apply Primer Paste evenly with a slim round
brush. Leave it for 120 sec., to enhance bonding
strength. Light cure for about 90sec.Then apply
Invisible Opaque to cover retention beads. Apply
thinly in margin area with no beads. Light cure
about 90 sec. again. Primer paste is a bonding
material, but at the same time it can be used as
Invisible Opaque, the use of Invisible Opaque is
not necessary. In this case, Primer Paste should
be applied thickly enough to cover retention
beads.
*Primer Paste can not be used for gold alloys.
1. Cut Back
Cut back forming crown. In cases where
Luna-Wing is used for anterior tooth or facing
crown, the occlusal area of the opposing tooth
must be metal-coated to avoid fracture.
Metal Frame Preparation
Basic Build-Up Layering for Crown Bridge 4. Opaque Application and Light Curing
Apply opaque with a flat brush thinly and light
cure for about 180 sec. In cases where the
metal color is visible, repeat this step until the
metal color is concealed.
*Do not apply thickly at one time.
Use Special Opaque Color to express
transparency of the incisal area or color of the
neck.
Form and light cure base to pontic area
Apply and light cure Opaque
1. Surface Treatment of Metal Frame
Sand-blast (about 0.2～0.25Mpa ) the surface using
alumina powder (about 50μm ), then use steam
cleaner or ultrasonic cleaner to wash and dry.
Alumina treatment of metal frame
Apply and dry primer
[ Basic Build-Up Layering for Crown Bridge］
Forming Examples
Facing Crown
3. Base Application and Light Curing
For pontic part, apply Primer Paste with a flat
brush to pontic area and light cure for about 90
sec. then apply base.
Adjust facing adjacent thickness, and light cure
for about 180 sec.
Make metal frame
*Conventional curing time is indicated in the following steps.
In case, the LED CURE Master is used, please confirm "Light Curing Schedule" on pade 9.

17 18
12. Polishing
Polish by using brush, fabric buff, and polishing
material to finish.
11. Finishing
Remove any scars with paper cone and silicon
point to make the surface smooth.
13. Complete
9. Final Light Curing
After final layering, light cure for about 180 sec.
as a final light curing.
8. Translucent Application and Light
Curing
In cases where Translucent is required, apply
Translucent and light cure for about 60 sec.
For the intermediate color expression between
Translucent and Enamel, apply Translucent
Enamel. For discoloring expressions, apply Effect
partially.
6. Dentine Application and Light Curing
Apply Dentine to form the required dentine core
shape and light cure for about 60 sec.
(If partial characterization of color adjustment is
necessary, apply desired color of Stain with
round brush and light cure for about 60 sec. )
Forming Examples
Facing Crown
[ Basic Build-Up Layering for Crown Bridge ］
5. Cervical (Opaque Dentine) Application
and Light Curing
Apply Cervical or Opaque Dentine starting from
the neck to the incisal area, applying
progressively thinner, taking subsequent color
gradation into consideration. Light cure for about
60 sec.
Form and light cure Body Resin
10. Corrections to Shape
Correct the shape using a carborundum or
diamond point.
*Additional Layering
In the case of additional layering after
corrections to shape, apply Repair Liquid thinly
and apply needed body resin. Light cure for 60
sec., the same steps as 5-10.
Figure adjustment and polish
Final light cure
7. Enamel Application and Light Curing
Apply Enamel to form the required crown shape
and light cure for about 60 sec.
*Conventional curing time is indicated in the following steps.
In case, the LED CURE Master is used, please confirm "Light Curing Schedule" on pade 9.

19 20
5. Dentine Application and Light Curing
Apply Dentine to form the required dentine core
shape and light cure for about 60 sec.
(If partial characterization of color adjustment is
necessary, apply desired color of Stain with
round brush and light cure for about 60 sec.)
6. Enamel Application and Light Curing
Apply Enamel to form contour and light cure for
about 60 sec.
8. Final Light Curing
After final layering, light cure for about 180 sec.
as a final light curing.
7. Translucent Application and Light
Curing
In cases where Translucent is required, apply
Translucent and light cure for about 60 sec.
For the intermediate color expression between
Translucent and Enamel, apply Translucent Enamel.
For discoloring expressions, apply Effect partially.
[ Basic Build-Up Layering for Jacket Crown ］
Forming Examples
Jacket Crown
4. Cervical(Opaque Dentine)Application
and Light Curing
Apply Cervical or Opaque Dentine starting from
the neck to the incisal area, applying
progressively thinner, taking subsequent color
gradation into consideration. Light cure for about
60 sec.
Form and light cure body resin
Final light cure
2. Resin Separator Application
For easier removal of jacket crown mould, apply
TWiNY Resin Separator thinly on margin area
and dry. Apply Opaque before TWiNY Resin
Separator gets completely dry.
Apply separator
3. Opaque Application and Light Curing
Apply Opaque with a flat bush thinly and light
cure for about 180 sec. In cases where the
metal color is visible, repeat this step until the
metal color is concealed.
*Do not apply thickly at one time.
Use Special Opaque Color to express
transparency of the incisal area or color of the
neck.
Apply and light cure Opaque
1. Resin Spacer Application
Make a plaster model in accordance with normal
practice.
Apply TWiNY Resin Spacer on surface, except
margin area and dry.
Make cementation
Making Plaster Model
*Conventional curing time is indicated in the following steps.
In case, the LED CURE Master is used, please confirm "Light Curing Schedule" on pade 9.

21 22
Starter Set, (Starter Set Hard)
Invisible Opaque 2.3mL：IvO
Opaque 2.3mL：OA2、OA3、OA3.5
Opaque Specialty Color 2.3mL：InO1、MO
Cervical 5g（3mL）：CA1、CA2
Dentine 5g（3mL）：DA2、DA3、DA3.5
Accessories ・Flat brushes (3) ・Round Brushes (3) ・Mixing Paper (50) ・Pallets (5) with shade cover (1)
Opaque Dentine 5g（3mL）：ODA2、ODA3、ODA3.5
Enamel 5g（3mL）：E2、E3 (or E2 Hard、E3 Hard)
Translucent 5g（3mL）：T (or T Hard)
Primer Paste 2.3mL
Repair Liquid 6mL
Regular Set, (Regular Set Hard)
Invisible Opaque 2.3mL：IvO
Opaque 2.3mL：OA1、OA2、OA3、OA3.5、OA4、OB2、OB3、OC3
Special Opaque Color 2.3mL：InO1、MO
Cervical 5g（3mL）：CA1、CA2、CB1、CC1
Dentine 5g（3mL）：DA1、DA2、DA3、DA3.5、DA4、DB2、DB3、DC3
Opaque Dentine 5g（3mL）：ODA1、ODA2、ODA3、ODA3.5、ODA4
Accessories ・Flat brushes (3) ・Round Brushes (3) ・Mixing Paper (50) ・Pallets (5) with shade cover (1)
Enamel 5g（3mL）：E2、E3、E4
（or E2 Hard、E3 Hard、E4 Hard)
Translucent 5g（3mL）：T (or T Hard)
Primer Paste 2.3mL
Repair Liquid 6mL
Intro Set, (Intro Set Hard)
Invisible Opaque 2.3mL：IvO
Opaque 2.3mL：OA3
Opaque Specialty Color 2.3mL：InO1、MO
Cervical 5g（3mL）：CA1
Dentine 5g（3mL）：DA3
Accessories ・Flat brushes (2) ・Round Brushes (3)
Opaque Dentine 5g（3mL）：ODA3
Enamel 5g（3mL）：E3 (or E3 Hard)
Translucent 5g（3mL）：T (or T Hard)
Primer Paste 2.3mL
Repair Liquid 6mL
Stain Kit
Stain 1mL：Blue、Yellow、Red、Orange、Dark Orange、White、Black、Gray、Brown、A Shift、B Shift
Stain Clear 6mL：Clear
Accessories ・Flat brushes (2) ・Mixing Paper (50) ・Pallets (5) with shade cover (1)
Red Plus Kit
Opaque 2.3mL：OA2R、OA3R、OA3.5R
Cervical 5g（3mL）：CA1R、CA2R
Dentine 5g（3mL）：DA2R、DA3R、DA3.5R
Line Up
For any further information or questions, please feel free to contact us.
[ Basic Build-Up Layering for Jacket Crown ］
Forming Examples
Jacket Crown
9. Corrections to Shape, Polishing and
Complete
Correct the shape using a carborundum or
diamond point.
After taking off jacket crown from plaster model,
adjust the surface with a silicone point, and
polish with brush, fables buff and polishing
material to finish.
*Additional Layering
In the case of additional layering after
corrections to shape, apply Repair Liquid thinly
and apply needed body resin. Light cure for 60
sec., the same steps as 4-8.
Finally, sand-blast (about 0.1～0.2Mpa)the inside
of the jacket crown using alumina powder
(about 50μm), then use steam cleaner or ultrasonic
cleaner to wash, and then dry.
Finish
Figure adjustment and polish
*Conventional curing time is indicated in the following steps.
In case, the LED CURE Master is used, please confirm "Light Curing Schedule" on pade 9.
http://www.yamakin-gold.co.jp
HeadOffice: 3-7 Sanadayama-choTennoji-kuOsaka 543-0015 ,Japan
BranchOffice:Tokyo,Osaka,Sendai,Nagoya,Fukuoka,JAPAN
FactoryandR&D:Kochi,JAPAN
P:+
81 - 6 - 6761 - 8338 F:+ 81 - 6 - 6761 - 0610
E:[e-mail]
YamamotoPreciousMetalCo.,Ltd.