Yard Works 060-3895-8 User manual

model number 060-3895-8
Please read and understand this manual before beginning
any use or assembly of the product, and make sure all
parts are present.
Questions?
If you have any questions or need replacement parts,
please call our toll-free helpline at 1-866-523-5218.
Instruction
Manual
5-Ton Dual-Wedge Log Splitter

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
2 3
Specifications Table of Contents
Product Name 5-Ton Dual-Wedge Log Splitter
Model Number 060-3895-8
Motor 120 V 60 Hz 15 A 1 3/4 HP
Log Capacity
(Diameter)
10" (25 cm) (single wedge)
10" (25 cm) (dual wedge)
Log Capacity (Length) 20 1/2" (52 cm) (single wedge)
17 11/32" (44 cm) (dual wedge)
Splitting Force 5 Tons
Hydraulic Pressure 20 MPa
Hydraulic Oil Capacity 3.2 L
DIMENSIONS
Length 37" (94 cm)
Width 10 1/2" (27 cm)
Height 20" (51 cm)
Product Weight 103 lb (46.8 kg)
Specifications 3
Important Safety Instructions 4
Symbols 6
Parts List 7
Exploded View 10
Parts Location 11
Important Information 12
Before Assembly 13
Assembly 15
Operation 16
Maintenance 21
Storage 23
Troubleshooting 24
Environmental Protection 25
Warranty 25
NOTE: The log capacity in diameter is only a guideline. A small
log can be difficult to split if it has knots or very tough fibre.

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
5
Important Safety Instructions
4
IMPORTANT! READ AND UNDERSTAND
ALL INSTRUCTIONS.
Failure to follow safety instructions may
result in electric shock, fire, and/or serious
personal injury.
• Read and understand all instructions and
all labels affixed to the log splitter. Learn
the applications, limitations, and specific
potential hazards before using this log
splitter.
PERSONAL SAFETY
• Do not operate the log splitter while under
the influence of drugs, alcohol, or any
medication.
• Stay alert, watch what you are doing, and
use common sense. Do not operate the log
splitter when you are tired.
• Dress properly. Do not wear loose clothing,
neckties, or jewellery that can get caught
and draw you into moving parts. Rubber
gloves and non-skid, steel-toed footwear
should be worn when working with the log
splitter. Wear protective hair covering to
contain long hair and prevent it from getting
caught in the log splitter.
• Always wear safety goggles. The use of a
log splitter can result in foreign objects being
thrown into your eyes which can result in
severe or permanent eye damage. Everyday
eyeglasses only have impact-resistant
lenses; they are not safety glasses.
• Never stand on the log splitter. Never allow
anyone to ride on the machine. Do not
transport anything or anyone on the log
splitter. Serious injury could occur if the
machine is tipped or jarred.
• Do not remove jammed logs using your
hand.
• Keep hands away from moving parts. Do not
place your hands in splits and cracks that
open in the log. They may close suddenly
which could cause severe crushing or
amputation.
• Keep your hands away from the controls
while logs are being loaded and unloaded.
Ensure that the loader and the operator are
positioned in the safe area at the control
end of the log splitter while the log pusher
is moving.
ELECTRICAL SAFETY
• Always unplug the log splitter from the
power supply when it is not in use, and
before making adjustments, changing parts,
cleaning, or servicing the log splitter.
• If an extension cord is needed, make sure
to use a proper extension cord. The cord
should be no longer than 32.5’ (10 m) with a
cross-section of no less than 1/8” (2.5 mm)
and a wire size (A.W.G.) of 12 in order to
allow sufficient flow of electric current to the
motor. An undersized cord may result in loss
of power and overheating.
• Electrical connections must be made with
protected material suitable for outdoor
use. Avoid using loose and inadequately
insulated connections.
• Only use an electrical circuit having
adequate protection and capacity
corresponding to the power, voltage,
and frequency of the log splitter. Ensure
that there is a ground connection and a
regulation differential switch upstream.
• Ground the log splitter. This log splitter is
equipped with an electric cord having an
equipment-grounding conductor and a
grounding pin. Insert the plug to a matching
electrical outlet. Do not modify the plug or
remove the grounding pin.
• Do not touch the metal prongs of the electric
cord plug when inserting or removing the
plug from an electrical outlet. Prevent body
contact with grounded surfaces such as
pipes, radiators, rangers, and refrigerators.
• Never open the pushbutton box. Contact a
qualified electrician if it is necessary to open
this box.
WORK AREA SAFETY
• Place the log splitter on a flat, stable, and
level surface that is 24–30” (60–75 cm) high.
Operate the log splitter in a location where
there is plenty of room for handling.
• To prevent unintended movement during
operation, anchor the log splitter to the work
area if it tends to slip, move, or slide.
• Keep the work area clean. A cluttered
workplace invites accidents. Do not leave
tools or pieces of wood on the log splitter
during operation.
• Before beginning any work using the log
splitter, make sure the work area has
sufficient lighting and that no obstructions
will interfere with the safety of operation.
• Do not operate the log splitter in dangerous
environments. Do not use the log splitter
in wet or damp conditions, and do not
expose it to rain. In order to avoid potential
fire hazards, never use the log splitter in
an explosive atmosphere where there
are fumes from paint, solvents, and other
flammable liquids.
• Keep children and visitors away. Never
allow children or untrained adults to
operate the log splitter.
• Make the workshop childproof. Disconnect
the power cord. Store the log splitter away
from children and other individuals not
qualified to use it. Keep the workshop
locked.
SAFE OPERATION
• Always check the oil level before using the
log splitter.
• Keep all guards in place and in working
order.
• Always inspect the log splitter before
turning it on. Make it a habit to check the
log splitter for oil leaks around the ram
cylinder. Do not operate the log splitter if
oil is leaking. Refer to the Troubleshooting
section in this manual.
• Check for damaged parts. Inspect the log
splitter, including the splitting wedge and
guards, for any malfunctioning or damaged
components, cracks, and deformation.
Replace damaged, missing, or faulty parts
before using the log splitter.
• Check for alignment of moving parts,
binding of moving parts, mounting and
any other conditions that may affect the
operation of the log splitter.
• Do not place the log splitter on the ground
during operation. Doing so creates an
awkward operating position in which the
operator’s face is close to the machine thus
increasing the risk of being struck by wood
chips or debris.
• The log splitter must always be operated
by only one person. If another person is
helping to load logs to be split, do not start
the machine until that person is clear of the
operating zone. Never ask another person
for help in freeing a jammed log.
• Inspect the log before loading it on the
log splitter. Ensure there are no nails or
foreign objects in the logs to be split. The
logs should be cut as squarely as possible.
Branches must be cut off flush with the
trunk.
• Always pay attention to the movement of
the log pusher. Do not load a log until the
log pusher has stopped. Do not attempt
to remove split logs until the machine has
totally completed its work cycle and has
stopped.
• Never attempt to split more than one log
at a time.
• Do not force the log splitter. It will do the job
better and safer at the feed rate for which it
was designed.
• Do not attempt to split logs that are
larger than the log capacity indicated in
the Specifications section. Doing so is
dangerous and may damage the machine.
• Only use the log splitter for its intended
purpose. Do not force the machine to do a
job for which it was not designed.
• Never leave the log splitter unattended
while it is running. Turn the power off. Do
not leave the machine until it comes to a
complete stop.
• Consult the instruction manual before
servicing. Product repairs and service
must be performed only by qualified repair
personnel.
• Maintain the log splitter with care. Keep
the log splitter clean and the blade sharp
for better and safer performance. Follow
instructions for lubricating and changing
accessories.
• Do not dump used oil into drains, soil,
or water. Dispose of used oil only at an
authorized collection point, or follow the
regulations that are in effect in your area.
• Only use the parts and accessories
supplied with this product or specifically
designated for use with this product
by the manufacturer. Using other parts
and accessories not designated by the
manufacturer could result in personal injury
or property damage.
Important Safety Instructions
SAVE THESE INSTRUCTIONS.

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
76
Part List
Item Description Qty
1 Lever Mount Nut 1
2 Nut Cap M10 3
3 Lever 1
4 Lever Knob 1
5 Guard Plate 1
6 Nut 2
7 Copper gasket 4
8 Screw M8 1
9 O-Ring 5.5 x 2 1
10 Snap Washer – Shaft 1
11 Valve Retract Spring 1
12 O-Ring 6.7 x 1.8 1
13 Valve Core Rod 1
18 Aluminum Cover (Rear) 1
19 O-Ring 55 x 3.1 1
20 Piston 1
21 Piston ring 1
22 O-Ring 32 x 3.5 1
23 Spring 1
24 Stud 4
25 Hydraulic Cylinder 1
26 Aluminum Cover (Front) 1
27 Piston Rod Seal 1
28 O-Ring 7 x 1.9 1
29 Bleed Screw 1
30 Flat Washer Groupware M14 1
31 Dipstick 1
32 Piston Rod 1
34 Screw M6 x 16 2
35 Frame Tube 1
36 Lead Plank 2
37 Spring Washer M6 4
38 Screw M6x10 6
39 Nut M14 2
40 Flat Washer 2
Symbols
Symbol Name Designation/Explanation
Read the
instruction
manual.
User must read and
understand the instruction
manual and all labels
affixed to the product
before using this product.
Inspect the
log splitter.
Inspect the log splitter
for any malfunctioning or
damaged components.
Dress properly.
Do not wear loose
clothing, gloves, neckties,
or jewellery (rings, wrist
watches), because
they can get caught in
moving parts. Wear non-
conductive protective
gloves and non-skid,
steel-toed footwear. Wear
protective hair covering to
contain long hair.
Protect your
eyes and face.
Always wear
safety goggles.
Everyday eyeglasses
only have impact-resistant
lenses. They are not
safety glasses.
Keep visitors
and children
away.
Always keep other people
a safe distance away from
the work area, especially
when the log splitter is in
use. The log splitter must
always be operated by
only one person.
Symbol Name Designation/Explanation
Avoid
injury from
unexpected
accidents.
Always pay attention to
the movement of the log
pusher. Keep hands and
body out of the way of all
moving parts.
Protect your
hands.
Keep your hands away
from splits and cracks
that open in the log. Do
not remove jammed logs
using your hands. Keep
hands off the controls
while logs are being
loaded and unloaded.
Disconnect
the power.
Unplug the log splitter
when it is not in use
and before making
adjustments, changing
parts, cleaning, or
servicing.
Protect the
environment.
Dispose of used oil
only at an authorized
collection point, or follow
the regulations that are in
effect in the area where
the log splitter is used.
Warning
Indicates a potentially
hazardous situation,
which, if not avoided
could result in death or
serious injury.
Caution
Indicates a potentially
hazardous situation,
which, if not avoided,
may result in minor or
moderate injury.
Note Notes and reminders for
the operator.

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
8 9
Item Description Qty
41 Nut 2
42 Nut plug 1
43 Flat Washer Groupware M18 1
44 Valve Sleeve 1
45 O-Ring 12.5 x 1.8 5
46 Adjusting Screw 1
47 Steel Ball 1
48 Pressure Limited Valve Spring 1
49 Adjusting Screw 1
50 Log Pusher Connection Weldment 1
51 Plastic Insert 1 1
52 Plastic Insert 2 1
53 Log Pusher 1
54 Nut M10 4
55 Flat Washer 5
56 Screw M10 x 25 4
57 Wheel Cover 2
58 Block Turn 2
59 Wheel 2
60 Washer 4
61 Wheel Shelf 1
62 Bolt 6
63 Spring Washer 9
64 Washer 9
65 Gear Pump Cover 1
66 O-Ring 10.6 x 2.65 2
67 Gear Housing Plate 1
68 C-Clip 2
69 Gear Shaft 1
70 Steel Ball 1
71 Gear 2
72 Pin 1
73 Washer 6
74 Bolt 3
75 Motor Cover 1
Item Description Qty
76 Seal 1
77 Nut 1
78 Screw 1
79 Motor 1
80 Fan 1
81 Block Turn 1
82 Shroud 1
83 Spring Washer 3
84 Screw 3
85 Leg 1
86 Washer 2
87 Bolt 2
88 Leg Cover 1
89 Cable & Plug 1
91 Cord Stop 1
93 Screw 11
94 Switch Box Cover 1
95 Airproof Underlay 1
96 Connection Terminal 1
97 Capacitor 1
98 Switch 1
99 Switch Box 1
100 Waterproof Underlay 1
101 Left Motor Support Shoe 1
102 Right Motor Support Shoe 1
103 Pin 2
104 Spring 2
105 Sliding Sleeve 4
106 Bolt 3
107 Fuse 1
108 Manual 1
110 Retaining Valve 1
111 Duo-Cut Blade 1
Parts List
Parts List

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
10 11
Item Description
1 Log pusher
2 Work table
3 Wedge
4 Support leg
5 Log retaining plates
6 Motor
7 Pushbutton box
8 Pushbutton switch
9 Wheels (for minor moving only)
10 Hydraulic control lever
11 Control lever guard
12 Bleed screw
13 Oil drain bolt with dipstick
14 Maximum pressure limiting screw
15 Dual wedge wedge
Exploded View
Parts Location
111
57
56 55 54 53 55
52
51
50
49
48
47
46 45 44 43
42
64 63
58 59 38 60
61
38
62 63 64 65 66 67 68 69 70 71 72 73
DE
F
C
AB
74 75 76
77 78
79 90 80 81
99 98 97
96
95 93 91 89
94
93
73 82 83 84 85
60
34
35
36
37
38
39
40
41
12
3
4
6
27
8
9
5
30
29
28
27
26
25
24
232221
20
19
18
13
12
11
10 31 32
86 87 88
108
110
106 105 104 103 102 101 100 107
105
11
10
9
32
12
13
8 7 6 5 4
1
14
10
15

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
12 13
Important Information
UNPACKING INSTRUCTIONS
This log splitter is shipped completely assembled with the exception of installing the wheels.
• Carefully remove the log splitter and its accessories from the box.
• Check and make sure all parts and accessories are included before using the log splitter
for the first time. Refer to the Parts Location section.
• Inspect the log splitter and its accessories for any damage.
• If there is any damage or missing parts and/or accessories, contact the customer service
helpline at 1-866-523-5218 before using the log splitter.
CHOOSING A LOCATION
• Choose a location where there is plenty of room for handling. Carefully lift the log splitter
from both ends and place the log splitter on a stable, flat, and level work surface that is
24–30" (60–75 cm) high.
TOOLS NEEDED FOR ASSEMBLY NOT SUPPLIED:
#6 Hex wrench
7/16 Box end wrench
WARNING! Failure to loosen the bleed screw may cause the seals in the
hydraulic system to rupture and cause serious physical injuries and/
or permanent damage to the log splitter. Make sure to loosen the bleed
screw prior to operating the log splitter.
WARNING! Do not adjust the maximum pressure limiting screw.
Unauthorized resetting may cause the hydraulic pump to weaken its
splitting pressure or it may result in serious personal injury and/or
damage to the log splitter.
1. INTENDED USE
This log splitter is intended for household use only. Do not use this log splitter for industrial
or other commercial application. Do not use the log splitter for processing any material
other than wood.
2. OPERATING FEATURES
2.1 BLEED SCREW
The bleed screw allows air to flow in and out of the oil tank.
2.2 MAXIMUM PRESSURE LIMITING SCREW
The maximum pressure was set at 5 tons in the factory. The limiting screw is sealed with
glue to ensure this setting will not change and the log splitter does not operate in splitting
pressures less than or exceeding 5 tons. The pressure was set by a qualified mechanic
using professional instruments.
2.3 DUAL WEDGE WEDGE
The Dual wedge wedge allows twice the effective splitting capacity of other similarly rated
electric log splitters
3. SAFETY FEATURES
3.1 ZHB CONTROL SYSTEM
This log splitter is equipped with a ZHB control system which means that the operator
must use both hands. The left hand controls the hydraulic lever, while the right hand controls
the pushbutton switch. If one hand lets go of either the switch or the lever, the log splitter
stops immediately.
model no. 060-3895-8 | contact us 1.866.523.5218
NOTE: The safe use of this product requires an understanding of
the information on the product and this operator’s manual as well as
knowledge of the project you are attempting. Before use of this product,
familiarize yourself with all operating features and safety rules.
Before Assembly
NOTE: This log splitter is designed to operate in ambient temperatures
between -20° and 40° C (-4° and 104° F). It can be stored or transported
in ambient temperatures between -25° and 55° C (-13° and 131° F).
24-30” (60-75 cm)

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
14 15
Before Assembly
ELECTRICAL REQUIREMENTS
• Use a standard 120 V (±10%) 60 Hz (±1 Hz) AC only electrical supply that has under-
voltage, over-voltage, and over-current protection devices as well as a residual current
device (RCD) with a maximum residual current rated at 0.03 A for the log splitter.
M
L
KH
SB
M
C
PE
N
Wiring diagram Plumbing diagram
WARNING! To reduce the risk of electric shock, this equipment has a
grounding type plug that has a third (grounding) pin. This plug will only
fit into a grounding type outlet. If the plug does not fit into the outlet,
please contact a qualified electrician to install the proper outlet.
Do not modify the plug or remove the grounding pin.
WARNING! Keep the extension cord clear of the working area. Route
the cord away from foot traffic so that it will not be tripped over or get
caught in lumber, tools, or other obstructions. Failure to do so can
result in serious physical injuries.
CAUTION! To avoid possible electric shock, switch off the power supply
at the main fuse or circuit breaker box before assembling, servicing, or
cleaning the log splitter.
CAUTION! Check and make sure that the log splitter is disconnected
from the power supply before installing the Dual wedge wedge.
WARNING! Always check all cords before each use. Never use a
damaged cord in order to avoid electrical shock resulting in serious
injury. Replace damaged cords before operating the log splitter.
120V
• If an extension cord is needed, use only a 3-wire
extension cord that has a 3-prong grounded
plug. The cord must be plugged into a matching
outlet that has 3 poles in the receptacle.
The extension cord must be no longer than
32.5' (10 m), have a cross-section of no less
than 1/8" (2.5 mm), and a wire size (A.W.G.) of
12. When working with the log splitter outdoors,
use only extension cords that are clearly marked
for outdoor use.
Assembly
1. ASSEMBLING THE WHEELS
• Install the wheel onto the axle with the front
side of the wheel facing outward.
• Push the hitch pin through the hole in the
axle until it locks.
• Place the wheel cover in the centre where
the axle protrudes from the wheel and push
to lock the wheel cover in place.
2. INSTALLING THE DUAL WEDGE WEDGE
• Remove the 4 sets of bolts and nuts from
the log pusher using a #6 Hex wrench for
the bolts and a 7/16 box end wrench for the
nuts. Set aside for later use.
• Remove the log pusher.
• Place the Dual wedge wedge in the welded
log pusher connection.
• Align the holes of the wedge to the holes on
the connection.
• Insert all the previously removed bolts and
nuts into the holes.
• Ensure that the wedge is in correct
position and then proceed to tighten all
bolts and nuts using the wrenches.
Log Pusher
Duo-cut Splitting Wedge

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
16 17
Operation
Operation
CAUTION!
• Before using the log splitter, make sure that the work area is clear of obstructions, clutter,
children, and pets. Work only in an area with ample lighting.
• Dress properly. Wear rubber gloves and non-skid, steel-toed footwear.
• When splitting logs, wear safety goggles to protect against eye injury.
1. CHECK THE OIL
• Ensure the log splitter is disconnected from the power supply.
• Using the support leg handle, stand the log splitter on the end with the wheels.
• Loosen the oil drain bolt and remove from the oil tank to see the attached oil dipstick.
• Wipe the dipstick clean and then re-insert
it back into the oil tank. Pull up the dipstick
and check if the oil level is between the
2 grooves on the dipstick.
• If there is not enough oil in the tank, refer
to “Replacing the Hydraulic Oil” in the
Maintenance section.
• After verifying that the oil level is correct,
insert the bolt with dipstick back into the
oil tank. Tighten the drain bolt in order to
avoid leakage, and then place the
log splitter back to its normal
horizontal position.
NOTE: Also check for oil leaks around the ram cylinder and other
points. Refer to the Troubleshooting section if there are oil leaks.
2. LOOSEN THE BLEED SCREW
• Turn the bleed screw 3 full turns.
• Leave the bleed screw in a vertical position
aligned behind the wedge or in a horizontal
position aligned with the work table in order
to avoid being sheared off by the split log
during operation.
3. USING THE LOG SPLITTER
a. Plug the power cord of the log splitter into the power supply.
b. Load the log into the log splitter
by placing the log lengthwise,
lying flat on the work table within
the log retaining plates, and in the
direction of the grain (fig. 1).
Bleed
screw
WARNING! Always loosen the bleed screw before operating the log
splitter. Failure to loosen the bleed screw may cause the seals in the
hydraulic system to rupture and cause serious physical injuries
and/or permanent damage to the log splitter.
Oil level
Oil drain bolt
with dipstick
1
WARNING! After 5 seconds of activation and the wood is not moving,
the pressurized oil becomes overheated and could damage the motor.
Never keep pressure on the wood by trying to force the log splitter for
more than 5 seconds. If the log is extremely hard, rotate the log 90°
in order to split it from the other side. If this doesn’t work, it means
that the hardness of the log exceeds the capacity of the log splitter
therefore, the log should be discarded. Do not force the log splitter to
split very hard wood.

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
18 19
Operation
c. The operator must be positioned at the
control end of the log splitter behind
the wheels as shown in figure 4.
WARNING!
• Do not place the log at an angle against the wedge to split the log on the upper part (fig. 2).
Doing so can break the wedge or damage the machine.
• Do not place the log crosswise on the splitter (fig. 3). This is dangerous and may seriously
damage the machine.
• Do not split more than one log at a time. One of them may fly out the splitter and cause injury.
• If the log is small, place it against the log pusher before starting the splitter.
• Do not try to split logs that are larger than the log capacity indicated in the Specifications
section.
WARNING! Do not crouch on the ground, sit down on a log beside the
splitter, or kneel down by the log splitter (fig. 5). Always keep your
hands and body out of the splitting or operating zone while using the
log splitter.
Operation
23
4
5
WARNING! After 5 seconds, the pressurized oil becomes overheated
and could damage the motor. Never keep pressure on the wood by
trying to force the log splitter for more than 5 seconds. If the log
is extremely hard, rotate the log 90° and try to split it in a different
direction. If this doesn’t work, it means that the hardness of the log
exceeds the capacity of the log splitter therefore, the log should be
discarded. Do not force the log splitter to split very hard wood.
NOTE: Both hands are required to start the log splitter.
Simultaneously holding the switch with your right hand and
pushing the hydraulic control lever down with your left hand
starts the hydraulic pump which pushes the log into the wedge.
If either hand is removed from either one of the controls, the log
splitter will automatically return to the starting position.
d. Using your right hand, push and hold down the pushbutton switch (fig. 6).
e. While holding down the switch with your right hand, use your left hand to push the
hydraulic control lever down (fig. 6).
6

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
20 21
Operation
REPLACING THE HYDRAULIC OIL
Replace the hydraulic oil in the log splitter after every 150 hours of use.
When replacing the hydraulic oil, it is recommended to use one of the following:
• 10W AW32
• ASLE H-150
• ISO 32
• Check and make sure that all moving parts have
come to a complete stop.
• Turn off the log splitter and unplug it from the power
supply.
• Using the support leg handle, stand the log splitter on
the end with the wheels.
• Unscrew the oil drain bolt with dipstick and remove it.
• Tilt the log splitter onto the support leg over a 4-liter
container in order to drain the hydraulic oil (fig. 11).
WARNING! To avoid possible electric shock, always disconnect the
log splitter from the power supply and tighten the bleed screw before
cleaning, making adjustments, or conducting maintenance work on
the log splitter.
Maintenance
11
3.2 L
HYDRAULIC
OIL
12
• Using the support leg, tilt the log splitter
back onto the motor side.
• Using a funnel (not provided), refill the
oil tank with the proper volume of fresh
hydraulic oil (fig. 12).
g. Repeat steps b through f for the other logs.
h. When the splitting of all logs is complete
or if the machine will be unattended for any
period of time, unplug the cord from the
power supply (fig. 8).
i. To avoid oil leakage, tighten the bleed screw
when moving the log splitter or when the log
splitter is no longer in use.
4. FREEING A JAMMED LOG
• Release both the switch and the hydraulic control lever.
• After the log pusher moves back to its starting position
and comes to a complete stop, insert a piece of wood
or wood wedge that fits on the splitter behind or under
the jammed log (fig. 9).
• Simultaneously hold down the switch using your right
hand and push the hydraulic control lever down using
your left hand to start the log splitter. The piece of
wood will move forward freeing the jammed log.
• If the log is not freed, repeat this procedure with a
steeper sloped piece of wood until the log is free.
WARNING! Do not try to knock the jammed log off the log splitter
(fig. 10). Doing so will damage the machine or cause the log to fly out
of the splitter which could result in an injury.
f. Stop the log splitter by simultaneously
releasing the hydraulic control lever and
the switch (fig. 7). Wait for the log pusher
to return to its starting position.
7
120V
120V
8
9
10

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
22 23
Maintenance
• Wipe the dipstick clean and insert it back into the oil tank to check for the oil level.
• Remove the dipstick and check for oil level. The level of the refilled oil should be between
the 2 grooves of the dipstick. If not, add or decrease the amount of oil in the tank until the
level is between the 2 grooves of the dipstick.
• After verifying that the oil level is
correct, insert the bolt with dipstick
back into the oil tank. Tighten the
drain bolt in order to avoid leakage,
and then place the log splitter back
to its normal horizontal position.
Note:
• Check the oil level regularly and before starting the log splitter. Ensure that the oil level is
between the 2 grooves on the dipstick. When the oil level is below the lower groove, refill
the oil tank before operating the log splitter.
• Dispose of used oil only at an authorized collection point, or follow the regulations that
are in effect in your area.
Maintenance
SHARPENING THE BLADE
After using the log splitter for some time, sharpen the blade or wedge using a fine-toothed
file. Smooth out any burns or crushed areas along the cutting edge.
CLEANING
• Use a clean cloth to remove dirt, dust, oil, and grease. Use a soft brush on the splitting
area and the motor ventilation area to remove any wood debris.
• DO NOT immerse the log splitter in water or other cleaning agents.
STORAGE
• Turn off the motor and unplug the log splitter from the power supply.
• Close the bleed screw to prevent oil leakage and clean any debris from the log
splitter before storing.
• Store the log splitter in a cool, dry location that is not accessible to children and
other unauthorized persons. Secure the log splitter and make sure it cannot fall
over and cause damage or injury.
Storage
Oil level
Oil drain bolt
with dipstick

model no. 060-3895-8 | contact us 1.866.523.5218 model no. 060-3895-8 | contact us 1.866.523.5218
24 25
Problem Possible Reason Solution
The log
splitter
does not
split logs.
The log is not positioned correctly. Refer to the Operation section for
instructions on proper log loading.
The size or hardness of the log
exceeds the capacity of the machine.
Reduce the size of the log before
splitting it on the log splitter.
The wedge cutting edge is blunt.
Refer to “Sharpening the blade”
under the Maintenance section for
instructions on how to sharpen the
cutting edge.
There is an oil leak. Locate the leak, and call the
helpline.
An unauthorized adjustment was
made to the maximum pressure
limiting screw—a lower maximum
pressure was set.
Call the helpline.
The log pusher
moves jerkily,
makes an
unfamiliar
noise, or
vibrates
excessively.
Not enough hydraulic oil and too
much air in the hydraulic system.
Check the oil level, and refill the
oil if necessary. If the problem
persists, call the helpline.
Oil leaks
around the
ram cylinder
or from other
points.
Air was sealed in the hydraulic
system during operation.
Loosen the bleed screw by
3 or 4 rotations before operating
the log splitter.
The bleed screw was not tightened
before moving the log splitter.
Tighten the bleed screw before
moving the log splitter.
The hydraulic control valve
assembly and/or seal are worn. Call the helpline.
Troubleshooting
Used electrical products are recyclable and should not be discarded
in your regular domestic waste. Please actively support us in
conserving resources and protecting the environment by returning
this appliance to a collection centre (if available).
Do not dump used oil into drains, soil, or water. Dispose of used oil
only at an authorized collection point or follow the regulations that
are in effect in your area.
Environmental ProtectionWarranty
WARRANTY
For TWO YEARS from the date of purchase within Canada, YARDWORKS CANADA will, at its
option, repair or replace for the original purchaser, free or charge, any part or parts found to be
defective in material or workmanship.
This warranty does not cover:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident,
improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Full One Hundred Twenty Days Warranty on Normal Wear Parts: Normal wear parts are defined as
blade adaptors, blades, grass bags and tires. These parts are warranted to the original purchaser to
be free from defects in material and workmanship for a period of one hundred twenty (120) days from
the date of retail purchase.
How to Obtain Service: Warranty service is available by calling the toll-free helpline, at
1 866-523-5218. The factory will not accept the return of a complete unit unless prior written
permission has been extended by YARDWORKS CANADA.
Transportation Charges: Transportation charges for the movement of any power equipment unit or
attachment are the responsibility of the purchaser. The purchaser must pay transportation charges
for any part submitted for replacement under this warranty unless such return is requested in writing
by YARDWORKS CANADA.
Other Warranties: All other warranties, express or implied, including any implied warranty of
merchantability is limited in its duration to that set forth in this express limited warranty. The
provisions as set forth in this warranty provide the sole and exclusive remedy of YARDWORKS
CANADA obligations arising from the sale of its products.
YARDWORKS CANADA will not be liable for incidental or consequential loss or damage.

Imported by YardWorks Canada
Toronto, Canada M4S 2B8