Yazoo/Kees ZKW42170 User manual

Professional Quality Lawn Care Equipment
since 1945
Thank you for buying a YAZOO/KEES ZT Max! Before operating your new mower, read,
understand and follow the important safety instructions and the other instructions con-
tained in this manual. Lawnmowers and all power equipment, can be potentially danger-
ous if used improperly. SAFETY REQUIRES GOOD JUDGEMENT, CAREFUL USE IN
ACCORDANCE WITH INSTRUCTIONS AND COMMON SENSE.
Operator’s Manual for
MODELS: ZKW42170
ZKW48170
MANUAL103337REV.04(12/13/00)

2
Continuous dedication to improve our products require that specifications and design are
subject to change without notice.
Congratulations on the purchase of your Yazoo/Kees mower. This manual has been pre-
pared for the owners and operators of the ZT MAX™ 42" and 48" commercial mowers. Read,
understand and follow the saftey and operating instructions.
! WARNING
Failure to follow cautious operating practices can result in serious injury to the operator or
other persons. The owner must understand these instructions, and must allow only trained
persons who understand these instructions to operate the mower. Each person operating
the mower must be of sound mind and body and must not be under the influence of any mind
altering substance.
If you have any questions pertaining to your mower contact your dealer.
! CAUTION
1. Keep all shields, guards and safety devices in place and in proper working condition.
2. Stop engine and remove spark plug wires or remove key before adjusting, servicing, or
performing maintenance.
WARNING: Engine exhaust, some of it’s constituents, and certain vehicle componets
contain or emit chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
WARNING: Battery posts, terminals and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. Wash hands after handling.

3
TABLE OF CONTENTS
SAFETY:
1.Training
2.Preparation
3.Operation
4.Transportation
5.Maintenance
SETUP AND ADJUSTMENTS:
1. Park brake
2.Cuttingheight
3.Frontdeck belt routing
4.Throttlelever tension
5.Reversespringdetent adjustment
6.Motioncontrollinkageadjustment
OPERATING INSTRUCTIONS:
1.Controls
2.Startingand operation
MAINTENANCE:
1.Engineoil level
2.Pumpcompartment
3.Mower blades
4.Safetyinterlocksystem
5.Hardware
6.Air cleaner
7. Engine oil
8.Hydraulicoil
9.Tire presure
10.Battery
11. Belts
12.Lubrication
13.Fuelfilter
14.Hydraulicfilterandoil
TROUBLE SHOOTING:

4
SAFETY
TRAINING:
1. Read this manual carefully and question your dealer if something is not clear.
2. Be thoroughly familiar with the controls and proper use of the equipment.
3. Never allow children, teenagers, or people unfamiliar with these instructions to use the
mower.
4. Do not mow while people, particularly children, or pets are nearby.
PREPARATION:
1. The use of personal protective equipment such as (but not limited to) protection for the
eyes, ears, feet and head is recommended.
2. Never operate the mower without proper guards, covers, safety switches and devices in
place and properly functioning. Inspect these items daily for their condition and proper op-
eration. If the condition or operation of any of these devices is questionable they must be
replaced or repaired before using the mower.
3. Thoroughly inspect the area to be mowed and remove all stones, sticks, wire and other
debris that may be thrown by the mower. Also note or mark other obstacles such as holes,
stumps, etc..
4. Do not operate the mower when barefoot or wearing open shoes. Always wear substantial
footwear and long pants.
5. Fill gas tank(s) before starting mower. DO NOT SMOKE near gasoline containers. Do not
fill gas tank indoors or when engine is hot or running. Clean off any spilled gasoline before
starting the mower.
OPERATION:
1. Mow only in daylight or good artificial light.
2. Do not operate the mower in wet grass if possible.
3. Mow up and down slopes. Use extreme caution when mowing or turning on slopes.
Always turn to the downhill side. Do not mow excessively steep slopes ( mower may tip
over and cause injury or death ).
4. Use caution when backing up.
5. Stop the blades when crossing surfaces other than grass; or when traveling to and from
the area to be mowed.
6. Never operate the mower with defective, broken or excessively worn parts. Keep all
guards, shields, and safety devices in place and in proper working order.
7. Do not change the engine governor settings or over speed the engine. Operating the
engine at excessive speeds will increase the hazard of injury and can severely damage your
machine.
8. Keep hands, feet and clothing away from rotating parts when operating mower.
9. Stop the blades and engine and set park brake before leaving the operators position for
any reason.
10. Never make adjustments to the mower while engine and/or blades are running.
11. After striking a foreign object, stop mower and remove key. Inspect the mower for any
damage and repair it immediately before continuing to mow.
12. Never operate this equipment in an enclosed or confined area without proper ventilation
of the engine exhaust.
13. Do not allow any passengers to ride on the mower. It is designed for the operator only.
Keep others away from the mower when in operation.

5
SAFETY
TRANSPORTATION:
Use a heavy duty trailer to haul mower. Set park brake, turn off fuel valve and strap mower to
trailer. NOTE: Park brake will not hold mower in place when transporting. Be sure to tie down
the mower to the trailer. Always back onto the trailer to prevent possible tipover.
1. Keep all nuts, bolts and screws tight to keep mower in safe operating condition.
2. Engine maintenance should comply with engine manufactures specifications. See the
engine manual for specifications.
3. Never store the mower with gas in the tank inside a building where fumes can reach an
open flame or spark.
4. To reduce the risk of fire, keep the mower free of grass, leaves and excessive grease or
oil.
5. Have your mower inspected and serviced each year by an authorizedYazoo/Keesdealer.
6. Use only authenticYazoo/Kees replacement parts to insure the safety and quality of your
mower is maintained.
7. Safety decals should be replaced if they are missing or illegible. Decals can be purchased
from your Yazoo/Kees dealer.
8. The hydraulic system including all hoses and fittings should be checked frequently for
wear or leaks. Never check for leaks with your hands, use a piece of cardboard or wood.
Hydraulic oil under pressure could be injected into your body and must be surgically removed
within a few hours.
EQUIPMENT SETUP AND ADJUSTMENTS
1. Uncrate mower
2. Mount drive wheels using the four lug nuts installed on the hub.
3. Check tire pressure in all four tires. Pressure for all four tires is 15 psi
4. Remove the motion control levers and install on the outside of the control arms (See figure
1). Tabs on the motion control levers should be directed to the rear of the mower. Align the
levers so they are even in the neutral position. (See figure 6)
5. Installseatlanyard to the seatframewith 5/16" hardware. Seat lanyardislocated under the
seatinthehydraulicpumparea.Attachthelanyardtotheleftfrontseatstudontheseatframe.
6. Check engine oil with dip stick. Add if needed per engine manufactures specifications.
(SeeKawasakiengine manual for engine specifications.)
7. Loosen the discharge chute slightly and lower into position. Chute should be snug but still
pivotfreely. Figure 1

6
ADJUSTMENTS
PARK BRAKE:
1.Stopengine andremovekey. Whilethe parkbrakelever”A”isintheonpostion. Thedistance
betweentheswivel”C”andthe bolt head”B” should be 3/8” to 1/2”approximately.(SeeFig.2)
2. If adjustment is needed, using two 1/2” wrenchs, loosen the nut”F” above the turnbuckle”G”
whileholdingtheturnbuckle”G”fromturning. Afterthenut”F”islooseandoutoftheway. While
holdingthebolthead”B”fromturning. Turntheturnbuckle”G”theproperdirectiontolengthenthe
distance or to shorten the distance. After the proper distance is obtained retighten the nut”F”
againstthe turnbuckle”G”.
3. While the park brake lever”A” is still in the on postion, measure the lenght of the spring”D”.
Shouldmeasure2”.(See Fig. 2)
4. If adjustment is needed loosen or tighten the nut”E” below the spring”D”. While holding the
turnbuckle”G”tokeep theassemblyfromturning.
CUTTING HEIGHT:
1. Beforechangingcuttingheights make sure the blades are off,keyswitchisoff, and the park
brakeison.(Neverchange the cuttingheightswiththemowerstill running.)
2. Thecuttingheight ranges from 1 1/2”to5.0”in 1/2” increments.(See Fig. 3a)
3. Tochangecuttingheightspullthehairpinsout of the bent arm pins. While hanging on to the
deckhandle,pull thebent armpinsoutofthedeckhangers,front andback. Choosethedesired
cutting height position and relocate bent arm pins and the hairpins. Repeat steps on the other
side.(See Fig. 3b)
FIGURE 2
FIGURE 3a FIGURE 3b

7
ADJUSTMENTS
FRONT DECK BELT ROUTING: (See Fig. 4)
Figure 4
THROTTLE LEVER TENSION:
1. Stop engine and remove key.
2. If throttle lever becomes loose, tension may be adjusted by tightening the pivot bolt. The
pivot bolt holds the throttle arm to the throttle mounting bracket which is located under the
console. Access is gained by removing the foot plate and the kick plate. See page 3.
REVERSE SPRING DETENT ADJUSTMENT:
1.Stop engine and remove key.
2.Pullthemotioncontrollever backtothereversepositionandreleasethelever. Whenthelever
stopsitshould be in line with theneutralslot,soyou can rotate the leveroutwithout hittingthe
sideofthe console.
3. If adjustment is needed put the seat in the rear slide position, tilt seat forward, remove seat
lanyardfromseatframe,androtateseatforwardto rest on the frame.
4.Onthebackof the console where the spring is fastened. Loosen3/8”nutandboltenoughto
allowthe bolt to slide inthe slot.(See Fig. 5a)
5. Rotate the motion control lever out into the neutral slot. While the lever is swung out pull it
againstthebackedgeofthe neutral slot. Holding the lever adjustthespringbyslidingtheboltin
the slot to remove all the slop and retighten the 3/8” nut and bolt.(Repeat steps on other side if
needed.)(See Fig. 5a)
6.Checkyouradjustmentbyrepeatingsteptwo.
7.Ifnomoreadjustmentisneededrefastentheseatlanyardtotheseatframe.

8
Figure 5a
(Leftsidecutawayview)
Figure 5b
(Leftsidecutawayview)

9
ADJUSTMENTS
MOTION CONTROL LINKAGE ADJUSTMENT:
1. This adjustment must be made with the drive wheels rotating. Raise rear of the unit and
block it up so the wheels are free to rotate. CAUTION:Keep hands, feet and clothing away
from rotating tires.
2.Tilt seat forward and remove theseatlanyardfromseat so the seat canrotatedownonto the
frame.Makesure the seat isadjustedtoward the rear of theunitso it clears thecontrolson the
console.
3.Placea2x4boardapproximatly10to12incheslongbetweenthefootplateandthecenterof
theseattoengagetheseatsafetyswitch.NOTE:Youmaywanttocovertheendofthe2x4with
aragto protect the seatfrommarring.
4.Loosenthenutsdirectlybehindeach ball joint on both rods that connect the pump armtothe
motion control assemblies. (See Fig 5b )
5.Starttheengine.Theparkbrakemustbeengagedand themotioncontrolleversmustbeinthe
neutralslot(Seefigure6page10)tostarttheengine.Runengineatapproximately1/2throttle.
6.Releaseparkbraketo allow wheels to rotate.CAUTION:Keephands,feetandclothingaway
fromrotatingtires.
7. Begin with either side and put the motion control lever into the neutral position. Adjust the
motion control linkage by rotating the double nuts on the rod in the proper direction until the
wheel stops rotating (See Fig 5b ).
Move the motion control lever forward then into the neutral position and place it into the
neutral slot. The wheel must be stopped completely at this point. Now do the same in reverse
and release the lever. The lever should return to neutral on its own. If not see reverse spring
detentadjustmentsection.
8.Runengineatfullthrottle to make sure wheels do notrotate.Readjustifanyrotationoccurs.
9.Repeatonthe opposite side and tighten nutsagainstballjoints.
10. Remove the 2x4 board and make sure the seat wiring is connected to the wiring harness.
WARNING: Seat must be connected for safety interlock system to properly function.
OPERATING INSTRUCTIONS
CONTROLS:
1. Be thoroughly familiar with all controls their function and how to operate them before
operating the mower.
2. Motion control levers located on each side of the console control direction of movement.
The left lever controls the flow of oil from the left hydro pump to the left wheel motor. The right
lever controls the flow of oil from the right hydro pump to the right wheel motor.

10
OPERATING INSTRUCTIONS
NOTE: To begin motion the operator must be in the seat and the brake disengaged before
the levers can be moved from the neutral slots or the engine will kill.
By moving the levers an equal amount forward or back the mower will move in a straight line
in that direction.
Movement of the right lever forward will cause the right wheel to rotate in a forward direction.
Movement of the left lever forward will cause the left wheel to rotate in a forward direction. To
stop forward travel pull levers back into the neutral position.
To turn right while moving in a forward direction pull the right lever back towards the neutral
position, this will slow the right wheel and cause the mower to turn in that direction.
To turn left while moving in forward direction pull the left lever back towards the neutral
position, this will slow the left wheel and cause the mower to turn in that direction.
To zero turn pull one lever back beyond neutral while holding the other slightly ahead of
neutral. NOTE: The direction of the zero turn will be determined by which lever is pulled back
beyond neutral. Thus, left lever back, left turn and opposite for right turn. Use caution when
using this maneuver unit can spin very rapidly if one lever is positioned too much
ahead of the other.
3. Blade engagement switch: Located on the console. Pull up on switch to engage blades,
push down to turn blades off. See page 3
4.Chokecontrol:Locatedonthe console.Pushthethrottlecontrolallthewayforward.Use when
startingcoldengine do not run chokewhenengine is warm. See page3
5. Throttle control: Located on the console. Used to control engine RPM. See page 3
6. Park brake: Located at the left end of the console. Pull lever back to engage the park
brake, push lever forward to release brake. NOTE: Use tie downs when transporting unit, the
park brake is not enough to hold the unit in place in this situation. See page 3
7. Key switch: Located on the console. The operator must be in the seat, park brake on,
motion control levers out in the neutral slots and blade switch off before engine will start. See
page 3
8. Fuel shut off valve: Located on the front of console at the top of the kick plate. The valve
has three positions left tank, right tank and straight down is the off position. See page 3
9.Pump release valves: Locatedatthe back left corner ofthepumps. Used to release thesys-
temsounitmaybemovedbyhandwhennotrunning.Tilttheseatuptogainaccesstothepumps.
Rotatevalvetowardsthefrontof the unit to release thesystemusinga5/8wrench.NOTE:Only
rotateabouta 1/4 of a turn toreleasesystem.

11
OPERATING INSTRUCTIONS
STARTING AND OPERATION:
1. Operator must be sitting in the seat. Engage park brake, blades off and place the motion
control levers in the neutral slots. (See figure 6)
2.Adjust throttle tochoke(ifneeded)turnkey and release as soon as engine starts,andadjust
1/2throttle.
3. Release park brake.
4.Closemotioncontrollevers.
5. Engage blades and set RPM to maximum, but not choked. NOTE: Be sure all persons are
clear of area before engaging the blades.To prolong spindle bearing and belt life engage and
disengagebladesatapproximately1\2throttle
MAINTENANCE
1.Engine oil level: Check dailywithengine cold and on a flatsurface.Remove the dipstick and
wipe clean. Reinsert the dipstick all the way,but do not screw down. Remove the dipstick and
checkoillevel.If oil level is low add oil.Useenginemanufacturersspecsfor type of oil.
2. Pump drive belt compartment: Stop engine and remove key. Tilt seat forward and clean all
debrisfrominside.NOTE:Cleaning may need to be done more frequently indryconditions.
3.Mowerblades:Stopengineandremovekey.Inspectbladesandsharpenorreplaceasneeded.
Check daily or more often if needed. The machine requires more power with dull blades and
gives a poor cut. If blades get bent, replace them. Blades shouldn’t have any notches from
hittingobjects. Theair foil ontopoftheblade should besufficienttoraisethe grass forcutting. If
bladesarein good condition,sharpenatanangleof22 to28degreesabout2-1/2inchesin from
the tips. Note: After sharpening, checkbladesfor proper balance, if neededcorrectbalanceto
preventexcessivevibration.
4. Safety interlock system: Check daily and never operate the mower if this system is not
functioning properly. The starter should crank only when the operator is in the seat, the park
brake set, blades off and the motion control levers in the neutral slots. If the mower starts with
any of these controls on or in an operating position, turn the mower off and repair the system
immediately.
Figure 6 (Right side)

12
MAINTENANCE
5. Hardware: Stop engine and remove key thoroughly inspect the entire machine for any
missing or loose hardware. Check daily.
6.Air cleaner: Stop engine and remove key. Remove plastic cover and loosen wingnut on the
air cleaner. Remove the foam pre-cleaner and wash or replace if needed. Inspect paper filter
and replace if dirty. Check every 25 hours, daily if in very dirty conditions. Fuel efficiency,
engine RPM, and available power goes down rapidly if the air filter is dirty. Prolonged effects
could damage the engine.
7.Engine oil: Change oil to manufacturers specifications. Stop engine and remove key. Drain
oil when engine is warm. Thoroughly clean around cap before removing. Remove oil
drain cap from the right side of engine block and replace drain cap. Remove oil filter and re-
place. Put a light coat of clean oil on the filter gasket before installing. Fill engine with oil using
manufacturersspecs,see Kawasakiowner’s manual. Startengineandidle slowlytoallowthe oil
torecoattheinterior of the engine and then inspectforleaks.
8. Hydraulic oil: Check daily. Stop engine and tilt seat forward.Thoroughly clean around
cap. Remove cap. Oil level should be even with the top of the baffle in the tank. If not, add oil.
NOTE:Useonly20w- 50 motor oil.
9. Tire pressure: Check every 25 to 50 hours. All four tires require 15 psi.
10.Battery: Maintance free
11. Belts: Check every 25 hours. Stop engine and remove key. Check the condition of all
belts.
Frontcasterpivots
Frontwheels
12.Lubrication(every25hours): Motion ControlBracketsLeft and Right
Pumpidlerpivot
Deck idler pivot
(Clean grease zerk thoroughly before greasing)

13
13. Fuel filter: Replace annually or as needed.
14. Hydraulic filter and oil: Change every 500 hours or yearly. Stop engine and remove key.
Clean around the filter and the drain plug on the bottom side of the tank. Remove the filter and
allowanyoil to drain from thefilterhead.Thenreplace with new filter. UseonlyYazoo/Kees p/n
102606, filter which has a bypass valve and the correct micron filter. Remove drain plug under
hydraulictankandallowtankto drain, reinstall drain plug. Fill tank with20w-50motoroiltothe
topofthe baffleinthetankand replacecap.Blockupthe rearofunituntilwheels willrotatefreely
andstartengine at a slow idle, movethemotion control levers forward and runforseveral min-
utes.Stop engine and recheck oil level. If wheels don’t responseanairlockhasoccuredwithin
thehydraulicsystem. Bleedair from lines,orletstandovernighttoallow the air timetodissipate
out of the oil. Retry responses & check the oil level. Note: Serious damage to the pumps and
wheelmotorscanoccur if the system is ran withanairlock.
MAINTENANCE

14
TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSES
Enginewon’t start
Mowerwillnotmove
ormovesslowlyor hard
1.Bladeswitchon.
2.Driveleversnotinthe neutral slots.
3.Operatornotinseat.
4. Park brake disengaged.
5.Dead battery or cable off.
....(Ignitionswitch lefton)
6.Fuelvalveclosedorinthe wrong position.
7.Nofuel.
8.Spark plug wires off.
9. Bad spark plugs.
1. Park brake on.
2.Pumpbypassvalvesopen.
3.Pump drive belt loose oroff.
4.Hydraulicsystem failure.
5.Airinthehydraulicsystem.
Blades won’t engage
Unevencut
Cut is ragged
Mowermoveswhen
inneutral position
Mowerpullsleftorright
When a problem occurs, do not overlook the simple causes.
For example, no fuel or battery disconnected when the engine will not start.
1.Tire pressureuneven.
2.Motioncontrollinkage adjustment.
3.Softterrian.
4. Slope too steep.
1.Motioncontrollinkageoutof adjustment.
2.Pumparmslooseoroutofadjustment.
3.Parkbrakeoutofadjustment.
1.Bladesdull.
2.Groundspeed too fast.
3.Grassaccumulationunderdeck.
1.Tire pressure uneven. (15 psi all tires)
2. Blades bent (check tip to tip one blade thickness)
3. Air foil of blade worn or bent.
1.Bladebeltoffofpulleys.
2.Clutchunhooked fromharness.
3.Bladeswitchfailure.
4.Fuseburnt out.

15
WIRING DIAGRAM

16
SERVICE RECORD
DESCRIPTIONOFWORKDONE
DATE SERVICE DONE BY

17
Yazoo/Kees Limited Two Year Warranty
1. This Limited two-year Warranty is issued by Yazoo/Kees Power Equipment, only to the
original purchaser. The warranty period is limited to ninety (90) days when product is or
has been used for rental purposes.
2. Yazoo/Kees warrants that all new equipment manufactured by Yazoo/Kees (Yazoo/Kees
Products), listed in paragraph 9 hereof, shall be free of defects in material and workmanship
for the term described in paragraph 4 below. Component parts, equipment, and accessories
not manufactured by Yazoo/Kees are not warranted hereunder, but are warranted by the
original manufacturer only to the extent of any original manufacturer’s warranty, with the
exceptionof the following;two yearson wheel motors,ninety dayson belts, hoses,tires, and
battery, one year on electrical components, and one yearon Peerless model 700 transmissions
(first ninety days warranted by Peerless, remainder by Yazoo/Kees).
3. In the event that any Yazoo/Kees Product warranted hereunder shall be defective or fail to
conform with this limited warranty, Yazoo/Kees shall, subject to the provisions hereof, pay
for, or provide labor and materials for, the repair or replacement of such defectiveYazoo/
Kees Product.
4. This limited warranty is for two years (24 months) from purchase date for Yazoo/Kees Prod-
ucts.
5. To obtain limited warranty service on a Yazoo/Kees Product use this procedure:
a. Locate the nearestYazoo/Kees dealer or distributor.
b. If you have moved, notify any Yazoo/Kees dealer or distributor in your area. You
must be able to confirm purchase date to validate your warranty.
c. Make arrangements to have the equipment delivered to the dealer or distributor
(refer to paragraph 6a).
d. If you have questions concerning the Yazoo/Kees Limited Warranty, they should be
referred to :
Yazoo/Kees Power Equipment
P.O. Box 8
700 Park Street
Beatrice, NE 68310
Attention:CustomerServiceDepartment
[phone]
e. Warranty service onYazoo/KeesProductsmust beperformed byanauthorizedYazoo/
Kees dealer.
6. This limited warranty does not cover the following:
a. Transportation to and from the Yazoo/Kees dealer or distributor.

18
b. Normal maintenance services and normal maintenance items such as brakes, brake
shoes, spark plugs, oil, air filters, mower blades, gauge wheels, skids and other wear
items.
c. Any Yazoo/Kees Product which had been altered or modified in any way.
d. Any repair or replacement caused by customer neglect or lack of maintenance. (The
purchaseris responsible for making sure thatYazoo/Kees Products are operated and
serviced as directed in the applicable manual or service instruction. Incorrect use or
maintenance will void this Limited Warranty.
7. YAZOO/KEES MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, OR WAR-
RANTIESAS TO THE MERCHANTABILITY OR FITNESS FORA PARTICULAR PUR-
POSE. ALL WARRANTIES ARE LIMITED IN DURATION TO THE TERMS SET OUT
IN PARAGRAPH 4, ABOVE. YAZOO/KEES SHALL HAVE NO LIABILITY FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE BREACH
OF ANY WARRANTY, INCLUDING, BUT NOT LIMITED TO, LIABILITY FOR INCON-
VENIENCE, RENTAL OR PURCHASES OF REPLACEMENT EQUIPMENT, OR FOR
LOSS OF PROFITS OR OTHER COMMERCIAL LOSS. SOME STATES DO NOT AL-
LOW A LIMITATION ON HOW LONGAN IMPLIED WARRANTY LASTS, SO THE
ABOVE STATEMENT MAY NOTAPPLY TO YOU. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIALDAM-
AGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
8. This warranty is not subject to change or modification by anyone, including Yazoo/Kees
dealers or distributors, and noYazoo/Kees dealer or distributor is authorized to make any
representations on behalf of Yazoo/Kees Power Equipment.
Note: This Warranty is for the following machines or products:
•ZTMax Midmount Riding Mowers
•Kutter Midsize Walk-behind Rotary Mowers
•Power Rake Dethatchers
•Power Slicer Aerators
•Core Plugger Aerators
•Classic High-wheel Walk-behind Rotary Mowers