Yeacomm P11K User manual

YEACOMM P11K User Manual
Thank you for choosing Yeacomm YF-P11K 4G wireless router Wifi
Kit, please read and keep the user manual carefully.
1. Main Technology Parameters
●Working temps : -30℃-- +60℃
●Relative humidity: 5%--95%
●Working frequency :
LTE: B1/2/3/5/7/8/20/38/40
LTE: B1/2/3/5/7/8/28/38/39/40/41(Optional)
●Power supply : input AC :100V~240V，50Hz~60Hz
Output DC: 15V, 1000mA
●Size: 252mm*112mm*58mm (Outdoor Unit)
105mm* 95mm*20mm (Indoor AP)
●Rate of uplink and downlink: LTE(Cat 4) 150Mbps/DL ；
50Mbps/UL
2. Product Interface and Indicator
2.1 Product interface
2.11 Outdoor router interface introduction
2.12 Indoor AP interface introduction
2.2 Indicator
2.21 Outdoor unit indicator
Type
Status
Description
RF
All off
no signal (the signal status can be
checked in the terminal configuration
page)
One on
Signal is poor
Two on
Signal is moderate
Three on
Signal is good
All on
Signal is very good
SYS
Off
Power abnormal, the router power off
On
Power normal, the router power on
SIM
Off
No SIM or can not detect SIM card
On
Device read the SIM normally
ETH
Off
Device doesn't connect to PC
On
Device connects to PC
RUN
Off
Device is not running
On
Device is running
2.22 Indoor unit indicator
Indicator
type
status
Description (from left to right )
POWER
Off
Power abnormal, the router power off
On
Power normal, the router power on
SIGNAL
Off
no signal
(the signal status can be checked in the
terminal configuration page)
Red
The signal is poor
Yellow
Signal is moderate
Green
Signal is good
WLAN
Off
WiFi off
Flicker
WiFi on and has data transmission
DATA
Off
Outdoor unit do not connect with
indoor unit .
On
Outdoor unit connects with indoor
unit .
WAN
Off
Outdoor unit does not connect with
indoor unit .
Light
Outdoor unit connects with indoor unit
LAN1/
LAN2
Off
Do not connect with PC
Light
Connect with PC correctly
3. Installation
3.1 Insert the sim card as below. When you hear a clicking sound, it
means that the USIM card has been installed successfully.
3.2 Connect the wan port of the indoor AP to the outdoor cpe router’s
POE port by Cate5e cable.
3.3 Place the outdoor unit outside in open space, the front panel face
to the base station. Make sure the unit is fixed well.

3.4 Power on the device, the system will automatically runs in 1~2
minutes.
Attention:
1) Do not insert the SIM card or remove it if power is
connected to the device.
2) Please use the power adapter that came with the device.
4. Quick Config Guide
Connect your PC/Laptop/Mobile to the router via Ethernet port or
WIFI. The router supports Windows XP, Windows 7/8/10, MAC OS,
Linux, Android and so on.
Regarding the router’s SSID and WIFI password information, pls see it
in the indoor AP’s sticker. No matter what way to connect, please make
sure to set the mode: obtain IP address automatically.
First Step：
Input CPE IP address(192.168.0.1) into the browser, press
“enter”
to
access CPE home page.
Second step：
If the router auto recognize the APN and already connect to
internet, then you do not need to add APN info.
If the router does not recognize the APN, then you need to add
APN manually. Pls select Device Settings--WAN Settings--APN,
fill in the APN info. Pls make sure the APN setting is correct.
Incorrect APN will cause internet connection failed.
5. Router Setting
If the device works fine, you’d better not change the parameter or
other function. If you changed it and cannot access Internet or have
poor experience, please press and hold the reset button for more
than 7 seconds to restore the factory settings.
Menu 1
Menu 2
Description
System
status
Home
gateway
information
status
Router running status info, such as
running hours, LTE network, SIM,
WAN, LAN, WLAN info
Online
terminal
status
Current terminal connections, MAC, IP
Traffic
Statistics
Traffic statistics
Version
info
Check the router's software and
hardware version number.
LTE info
Check LTE details info, including
frequency, cell, RSRP, SINR, RSRQ
etc.
Device
Setting
WAN
Setting
Network selection: Auto, 4G Prefer, 4G
Only, 3G Prefer, 3G Only, etc.
APN Setting
IPV4 / IPV6: Set router IP stack
support model.The default setting is
IPV4 / IPV6 dual stack.
PIN, MTU, DNS Settings
WLAN
Setting
Enable and disable wifi.
View and change WiFi SSID,
password, encryption and channels
DHCP
DHCP: Set the router’s DHCP info and
IP info. Once turn off the DHCP, the
user has to set IP manually, and it can
not obtain the IP automatically.
Keep address
IPV6 set
IPV6 address allocation, PNAT
function.
SMS
function
New
message
Creating a new message
Inbox
Inbox
Draft
Draft
Sent
Sent
Firewall
Filtering
Rules
Ports filtering, IP address filtering,
URL Filtering,.
MAC binding,
Speed limit
IP speed limit
System
manage
ment
System
setting
Change password, username, device
reboot settings and runtime.
System log
Check system work log
Reboot
Support reset router
System
update
Update the firmware
Module
update
LTE module software update
Config
update
Update router system setting
Restart
device
User can restart router